Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1653/35  Seat Position Airbag Sensor Circuit Malfunction  


DESCRIPTION

The seat position airbag sensor circuit consists of the airbag ECU assembly and seat position airbag sensor.

DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1653/35 Seat Position Airbag Sensor Circuit Malfunction
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the seat position airbag sensor circuit.

·

Seat position airbag sensor malfunction

·

Airbag ECU assembly malfunction


for LHD:
·

Floor wire

·

Front No. 2 seat wire LH

·

Seat position airbag sensor

·

Airbag ECU assembly


for RHD:
·

Floor wire

·

Front seat wire RH

·

Seat position airbag sensor

·

Airbag ECU assembly


Does not apply to test/check mode

WIRING DIAGRAM

for LHD:


C348586E01
5.354,2.917 5.802,3.229 0.448,0.313 10 false M1 5.354,3.073 6.875,3.396 1.521,0.323 10 false Airbag ECU Assembly 5.208,0.802 5.656,1.115 0.448,0.313 10 false 9 5.135,1.979 5.583,2.292 0.448,0.313 10 false 17 5.385,0.906 6.042,1.323 0.656,0.417 10 false LSP+ 5.385,2.073 6.042,2.49 0.656,0.417 10 false LSP- 3.427,0.906 4.083,1.323 0.656,0.417 10 false Ma3 0.573,2.917 1.021,3.229 0.448,0.313 10 false a9 0.563,3.073 2.635,3.396 2.073,0.323 10 false Seat Position Airbag Sensor 1.542,0.792 2.198,1.208 0.656,0.417 10 false VS 1.438,1.958 2.094,2.375 0.656,0.417 10 false GND 3.427,2.073 4.083,2.49 0.656,0.417 10 false Ma3 3.5,0.708 3.948,1.021 0.448,0.313 10 false 2 3.5,1.875 3.948,2.188 0.448,0.313 10 false 1 1.854,0.792 2.51,1.208 0.656,0.417 10 false 2 1.854,1.958 2.51,2.375 0.656,0.417 10 false 1


for RHD:


C348586E03
5.354,2.917 5.802,3.229 0.448,0.313 10 false M45 5.354,3.073 6.875,3.396 1.521,0.323 10 false Airbag ECU Assembly 5.135,0.802 5.583,1.115 0.448,0.313 10 false 16 5.135,1.979 5.583,2.292 0.448,0.313 10 false 24 5.385,0.906 6.042,1.323 0.656,0.417 10 false RSP+ 5.385,2.073 6.042,2.49 0.656,0.417 10 false RSP- 3.427,0.906 4.083,1.323 0.656,0.417 10 false Ma3 0.573,2.917 1.021,3.229 0.448,0.313 10 false a9 0.563,3.073 2.635,3.396 2.073,0.323 10 false Seat Position Airbag Sensor 1.542,0.792 2.198,1.208 0.656,0.417 10 false VS 1.448,1.958 2.104,2.375 0.656,0.417 10 false GND 3.427,2.073 4.083,2.49 0.656,0.417 10 false Ma3 3.5,0.708 3.948,1.021 0.448,0.313 10 false 2 3.5,1.875 3.948,2.188 0.448,0.313 10 false 1 1.854,0.792 2.51,1.208 0.656,0.417 10 false 2 1.854,1.958 2.51,2.375 0.656,0.417 10 false 1


CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
LHD A
RHD B



A

2.CHECK CONNECTORS

B

13.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and seat position airbag sensor. Also check that the connectors that link the front No. 2 seat wire LH and floor wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and seat position airbag sensor. Also disconnect the connectors that link the front No. 2 seat wire LH and floor wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)
a.
C265013C09
0.521,0.5 0.885,0.74 0.365,0.24 0.344,3.646 0.646,3.865 0.302,0.219 1.188,0.844 1.521,0.844 false 1.417,0.417 1.833,0.708 false 1.417,1.25 1.823,0.938 false 0.75,4.25 1.115,3.771 false 1.667,4.25 1.271,3.781 false 0.448,2.021 0.76,2.344 0.313,0.323 10 false *1 2.656,2.333 3.135,2.75 0.479,0.417 10 false *2 1.031,0.771 1.427,1.104 0.396,0.333 10 false *3 0.479,0.167 0.896,0.573 0.417,0.406 10 false *a 0.323,3.198 0.656,3.531 0.333,0.333 10 false *b 2.177,2.031 2.656,2.448 0.479,0.417 10 false A 1.927,2.031 2.406,2.448 0.479,0.417 10 false B 1.583,2.031 2.063,2.448 0.479,0.417 10 false C 1.427,2.031 1.906,2.448 0.479,0.417 10 false D 1.083,2.031 1.563,2.448 0.479,0.417 10 false E 0.833,2.031 1.313,2.448 0.479,0.417 10 false F 1.031,0.333 1.521,0.667 0.49,0.333 10 false LSP+ 1.052,1.177 1.51,1.521 0.458,0.344 10 false LSP- 0.625,0.542 1.021,0.875 0.396,0.333 10 false M1 1.594,4.25 1.99,4.583 0.396,0.333 10 false VS 0.583,4.25 0.979,4.583 0.396,0.333 10 false GND 0.427,3.677 0.823,4.01 0.396,0.333 10 false a9
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the connectors that link the front No. 2 seat wire LH and floor wire.


b.

Using a service wire, connect terminals 9 (LSP+) and 17 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a9-2 (VS) - a9-1 (GND) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

NG

12.CHECK FLOOR WIRE (OPEN)
4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)
a.
C283374C06
0.354,2.302 0.688,2.531 0.333,0.229 0.865,2.885 1.26,2.448 false 1.885,2.896 1.406,2.438 false 0.313,0.615 0.677,0.854 0.365,0.24 10 false *1 2.781,0.906 3.167,1.26 0.385,0.354 10 false *2 0.167,1.698 0.542,1.979 0.375,0.281 10 false *a 2.344,0.625 2.729,0.979 0.385,0.354 10 false A 2.031,0.625 2.417,0.979 0.385,0.354 10 false B 1.573,0.625 1.948,0.958 0.375,0.333 10 false C 1.417,0.625 1.792,0.958 0.375,0.333 10 false D 0.969,0.625 1.344,0.958 0.375,0.333 10 false E 0.656,0.625 1.031,0.958 0.375,0.333 10 false F 1.823,2.906 2.25,3.146 0.427,0.24 10 false VS 0.698,2.896 1.125,3.135 0.427,0.24 10 false GND 0.458,2.333 0.885,2.573 0.427,0.24 10 false a9
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a9-2 (VS) - a9-1 (GND) Always 1 MΩ or higher



Result:
Result
OK
NG



OK

5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

NG

11.CHECK FLOOR WIRE (SHORT)
5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)
a.
C283374C06
0.354,2.302 0.688,2.531 0.333,0.229 0.865,2.885 1.26,2.448 false 1.885,2.896 1.406,2.438 false 0.313,0.615 0.677,0.854 0.365,0.24 10 false *1 2.781,0.906 3.167,1.26 0.385,0.354 10 false *2 0.167,1.698 0.542,1.979 0.375,0.281 10 false *a 2.344,0.625 2.729,0.979 0.385,0.354 10 false A 2.031,0.625 2.417,0.979 0.385,0.354 10 false B 1.573,0.625 1.948,0.958 0.375,0.333 10 false C 1.417,0.625 1.792,0.958 0.375,0.333 10 false D 0.969,0.625 1.344,0.958 0.375,0.333 10 false E 0.656,0.625 1.031,0.958 0.375,0.333 10 false F 1.823,2.906 2.25,3.146 0.427,0.24 10 false VS 0.698,2.896 1.125,3.135 0.427,0.24 10 false GND 0.458,2.333 0.885,2.573 0.427,0.24 10 false a9
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a9-2 (VS) - Body ground Power switch on (IG) Below 1 V
a9-1 (GND) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

NG

10.CHECK FLOOR WIRE (SHORT TO B+)
6.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
a.
C283374C06
0.354,2.302 0.688,2.531 0.333,0.229 0.865,2.885 1.26,2.448 false 1.885,2.896 1.406,2.438 false 0.313,0.615 0.677,0.854 0.365,0.24 10 false *1 2.781,0.906 3.167,1.26 0.385,0.354 10 false *2 0.167,1.698 0.542,1.979 0.375,0.281 10 false *a 2.344,0.625 2.729,0.979 0.385,0.354 10 false A 2.031,0.625 2.417,0.979 0.385,0.354 10 false B 1.573,0.625 1.948,0.958 0.375,0.333 10 false C 1.417,0.625 1.792,0.958 0.375,0.333 10 false D 0.969,0.625 1.344,0.958 0.375,0.333 10 false E 0.656,0.625 1.031,0.958 0.375,0.333 10 false F 1.823,2.906 2.25,3.146 0.427,0.24 10 false VS 0.698,2.896 1.125,3.135 0.427,0.24 10 false GND 0.458,2.333 0.885,2.573 0.427,0.24 10 false a9
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a9-2 (VS) - Body ground Always 1 MΩ or higher
a9-1 (GND) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK DTC

NG

9.CHECK FLOOR WIRE (SHORT TO GROUND)
7.CHECK DTC
a.
C238211C05
0.5,0.833 0.719,1.083 0.219,0.25 10 false *1 0.833,0.823 1.031,1.094 0.198,0.271 10 false F 0.99,0.823 1.177,1.115 0.188,0.292 10 false E 1.438,0.823 1.677,1.104 0.24,0.281 10 false D 1.594,0.823 1.802,1.042 0.208,0.219 10 false C 2.042,0.823 2.25,1.063 0.208,0.24 10 false B 2.198,0.823 2.406,1.01 0.208,0.188 10 false A 2.615,1.104 2.896,1.375 0.281,0.271 10 false *2
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly


Connect the connectors to the airbag ECU assembly and seat position airbag sensor.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

8.CHECK SEAT POSITION AIRBAG SENSOR
8.CHECK SEAT POSITION AIRBAG SENSOR
a.
C238211C05
0.5,0.833 0.719,1.083 0.219,0.25 10 false *1 0.833,0.823 1.031,1.094 0.198,0.271 10 false F 0.99,0.823 1.177,1.115 0.188,0.292 10 false E 1.438,0.823 1.677,1.104 0.24,0.281 10 false D 1.594,0.823 1.802,1.042 0.208,0.219 10 false C 2.042,0.823 2.25,1.063 0.208,0.24 10 false B 2.198,0.823 2.406,1.01 0.208,0.188 10 false A 2.615,1.104 2.896,1.375 0.281,0.271 10 false *2
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Replace the seat position airbag sensor with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Restore the seat position airbag sensor that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

NG

9.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C348588C01
0.885,2.146 1.229,2.365 0.344,0.219 1.167,1.094 1.167,0.677 false 1.958,0.583 1.958,0.167 1.958,0.167 2.125,0.167 false 1.406,2.75 1.729,2.344 false 2.448,2.74 2.094,2.344 false 0.292,0.552 0.635,0.729 0.344,0.177 10 false *1 2.833,0.844 3.26,1.219 0.427,0.375 10 false *2 1.094,1.115 1.552,1.563 0.458,0.448 10 false *3 2.156,0.083 2.573,0.448 0.417,0.365 10 false *4 0.74,1.615 1.167,1.938 0.427,0.323 10 false *a 0.938,2.177 1.365,2.5 0.427,0.323 10 false Ma3 2.344,2.75 2.771,3.073 0.427,0.323 10 false LSP+ 1.26,2.75 1.688,3.073 0.427,0.323 10 false LSP- 2.458,0.563 2.885,0.938 0.427,0.375 10 false A 2.146,0.563 2.573,0.938 0.427,0.375 10 false B 1.677,0.563 2.104,0.938 0.427,0.375 10 false C 1.365,0.563 1.792,0.938 0.427,0.375 10 false D 0.896,0.563 1.323,0.938 0.427,0.375 10 false E 0.594,0.563 1.021,0.938 0.427,0.375 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*3 Front No. 2 Seat Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front No. 2 Seat Wire LH)


Disconnect the floor wire connector from the front No. 2 seat wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ma3-2 (LSP+) - Body ground Always 1 MΩ or higher
Ma3-1 (LSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT NO. 2 SEAT WIRE LH

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (SHORT TO B+)
a.
C348588C01
0.885,2.146 1.229,2.365 0.344,0.219 1.167,1.094 1.167,0.677 false 1.958,0.583 1.958,0.167 1.958,0.167 2.125,0.167 false 1.406,2.75 1.729,2.344 false 2.448,2.74 2.094,2.344 false 0.292,0.552 0.635,0.729 0.344,0.177 10 false *1 2.833,0.844 3.26,1.219 0.427,0.375 10 false *2 1.094,1.115 1.552,1.563 0.458,0.448 10 false *3 2.156,0.083 2.573,0.448 0.417,0.365 10 false *4 0.74,1.615 1.167,1.938 0.427,0.323 10 false *a 0.938,2.177 1.365,2.5 0.427,0.323 10 false Ma3 2.344,2.75 2.771,3.073 0.427,0.323 10 false LSP+ 1.26,2.75 1.688,3.073 0.427,0.323 10 false LSP- 2.458,0.563 2.885,0.938 0.427,0.375 10 false A 2.146,0.563 2.573,0.938 0.427,0.375 10 false B 1.677,0.563 2.104,0.938 0.427,0.375 10 false C 1.365,0.563 1.792,0.938 0.427,0.375 10 false D 0.896,0.563 1.323,0.938 0.427,0.375 10 false E 0.594,0.563 1.021,0.938 0.427,0.375 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*3 Front No. 2 Seat Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front No. 2 Seat Wire LH)


Disconnect the floor wire connector from the front No. 2 seat wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Ma3-2 (LSP+) - Body ground Power switch on (IG) Below 1 V
Ma3-1 (LSP-) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT NO. 2 SEAT WIRE LH

NG

REPLACE FLOOR WIRE

11.CHECK FLOOR WIRE (SHORT)
a.
C348588C01
0.885,2.146 1.229,2.365 0.344,0.219 1.167,1.094 1.167,0.677 false 1.958,0.583 1.958,0.167 1.958,0.167 2.125,0.167 false 1.406,2.75 1.729,2.344 false 2.448,2.74 2.094,2.344 false 0.292,0.552 0.635,0.729 0.344,0.177 10 false *1 2.833,0.844 3.26,1.219 0.427,0.375 10 false *2 1.094,1.115 1.552,1.563 0.458,0.448 10 false *3 2.156,0.083 2.573,0.448 0.417,0.365 10 false *4 0.74,1.615 1.167,1.938 0.427,0.323 10 false *a 0.938,2.177 1.365,2.5 0.427,0.323 10 false Ma3 2.344,2.75 2.771,3.073 0.427,0.323 10 false LSP+ 1.26,2.75 1.688,3.073 0.427,0.323 10 false LSP- 2.458,0.563 2.885,0.938 0.427,0.375 10 false A 2.146,0.563 2.573,0.938 0.427,0.375 10 false B 1.677,0.563 2.104,0.938 0.427,0.375 10 false C 1.365,0.563 1.792,0.938 0.427,0.375 10 false D 0.896,0.563 1.323,0.938 0.427,0.375 10 false E 0.594,0.563 1.021,0.938 0.427,0.375 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*3 Front No. 2 Seat Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front No. 2 Seat Wire LH)


Disconnect the floor wire connector from the front No. 2 seat wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ma3-2 (LSP+) - Ma3-1 (LSP-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT NO. 2 SEAT WIRE LH

NG

REPLACE FLOOR WIRE

12.CHECK FLOOR WIRE (OPEN)
a.
C348589C01
0.5,0.427 0.854,0.656 0.354,0.229 0.583,3.521 0.938,3.75 0.354,0.229 1.042,0.969 1.292,0.969 false 1.365,0.583 1.677,0.823 false 1.354,1.333 1.646,1.083 false 1.146,2.5 1.146,2.167 false 1.938,2.073 1.938,1.74 1.938,1.74 1.771,1.74 false 1.156,4.156 1.469,3.698 false 2.156,4.156 1.833,3.698 false 0.271,2.042 0.74,2.469 0.469,0.427 10 false *1 2.823,2.344 3.281,2.781 0.458,0.438 10 false *2 1.073,2.531 1.51,2.958 0.438,0.427 10 false *3 1.615,1.667 1.969,1.938 0.354,0.271 10 false *4 0.875,0.896 1.333,1.313 0.458,0.417 10 false *5 0.469,0.188 0.865,0.552 0.396,0.365 10 false *a 0.354,3.146 0.823,3.552 0.469,0.406 10 false *b 0.635,3.552 1.104,3.958 0.469,0.406 10 false Ma3 2.042,4.167 2.563,4.479 0.521,0.313 10 false LSP+ 1.021,4.167 1.542,4.479 0.521,0.313 10 false LSP- 1,0.5 1.521,0.823 0.521,0.323 10 false LSP+ 1,1.26 1.583,1.594 0.583,0.333 10 false LSP- 0.594,0.458 1.115,0.771 0.521,0.313 10 false M1 2.427,2.042 2.885,2.479 0.458,0.438 10 false A 2.125,2.042 2.583,2.479 0.458,0.438 10 false B 1.656,2.042 2.115,2.479 0.458,0.438 10 false C 1.344,2.042 1.802,2.479 0.458,0.438 10 false D 0.875,2.042 1.333,2.479 0.458,0.438 10 false E 0.563,2.042 1.021,2.479 0.458,0.438 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*3 Front No. 2 Seat Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Front No. 2 Seat Wire LH)


Disconnect the floor wire connector from the front No. 2 seat wire LH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ma3-2 (LSP+) - Ma3-1 (LSP-) Always Below 1 Ω



c.

Disconnect the service wire from the connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT NO. 2 SEAT WIRE LH

NG

REPLACE FLOOR WIRE

13.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and seat position airbag sensor. Also check that the connectors that link the front seat wire RH and floor wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and seat position airbag sensor. Also disconnect the connectors that link the front seat wire RH and floor wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

14.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

14.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)
a.
C284677C08
0.604,0.667 0.958,0.917 0.354,0.25 0.542,3.594 0.896,3.844 0.354,0.25 2.115,0.802 2.5,0.5 false 2.104,1.083 2.5,1.333 false 1.083,4.25 1.5,3.792 false 2.167,4.25 1.698,3.792 false 2.792,0.927 2.458,0.927 false 0.438,2.448 0.833,2.781 0.396,0.333 10 false *1 2.646,2.167 2.958,2.583 0.313,0.417 10 false *2 2.823,0.844 3.125,1.167 0.302,0.323 10 false *3 0.521,0.167 0.833,0.5 0.313,0.333 10 false *a 0.344,3.229 0.656,3.552 0.313,0.323 10 false *b 2.094,4.25 2.51,4.583 0.417,0.333 10 false VS 2.531,1.25 3.115,1.573 0.583,0.323 10 false RSP- 0.656,0.708 1.125,1.031 0.469,0.323 10 false M45 2.177,2.469 2.49,2.885 0.313,0.417 10 false A 1.927,2.458 2.24,2.875 0.313,0.417 10 false B 1.583,2.458 1.896,2.875 0.313,0.417 10 false C 1.427,2.458 1.74,2.875 0.313,0.417 10 false D 1.083,2.458 1.396,2.875 0.313,0.417 10 false E 0.844,2.458 1.156,2.875 0.313,0.417 10 false F 2.531,0.417 3.031,0.75 0.5,0.333 10 false RSP+ 0.938,4.25 1.438,4.656 0.5,0.406 10 false GND 0.656,3.635 1.125,3.958 0.469,0.323 10 false a9
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the connectors that link the front seat wire RH and floor wire.


b.

Using a service wire, connect terminals 16 (RSP+) and 24 (RSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a9-2 (VS) - a9-1 (GND) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

NG

23.CHECK FLOOR WIRE (OPEN)
15.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)
a.
C284678C07
0.531,2.156 0.896,2.406 0.365,0.25 1,2.917 1.438,2.417 false 2.083,2.917 1.667,2.417 false 0.427,0.969 0.76,1.219 0.333,0.25 10 false *1 2.667,0.677 3.063,1.01 0.396,0.333 10 false *2 0.354,1.74 0.75,2.156 0.396,0.417 10 false *a 2.198,0.969 2.594,1.302 0.396,0.333 10 false A 1.927,0.979 2.323,1.313 0.396,0.333 10 false B 1.583,0.979 1.979,1.313 0.396,0.333 10 false C 1.417,0.979 1.813,1.313 0.396,0.333 10 false D 1.073,0.979 1.469,1.313 0.396,0.333 10 false E 0.802,0.969 1.198,1.302 0.396,0.333 10 false F 2.01,2.917 2.49,3.25 0.479,0.333 10 false VS 0.844,2.917 1.51,3.25 0.667,0.333 10 false GND 0.646,2.198 1.313,2.531 0.667,0.333 10 false a9
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a9-2 (VS) - a9-1 (GND) Always 1 MΩ or higher



Result:
Result
OK
NG



OK

16.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

NG

22.CHECK FLOOR WIRE (SHORT)
16.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)
a.
C284678C07
0.531,2.156 0.896,2.406 0.365,0.25 1,2.917 1.438,2.417 false 2.083,2.917 1.667,2.417 false 0.427,0.969 0.76,1.219 0.333,0.25 10 false *1 2.667,0.677 3.063,1.01 0.396,0.333 10 false *2 0.354,1.74 0.75,2.156 0.396,0.417 10 false *a 2.198,0.969 2.594,1.302 0.396,0.333 10 false A 1.927,0.979 2.323,1.313 0.396,0.333 10 false B 1.583,0.979 1.979,1.313 0.396,0.333 10 false C 1.417,0.979 1.813,1.313 0.396,0.333 10 false D 1.073,0.979 1.469,1.313 0.396,0.333 10 false E 0.802,0.969 1.198,1.302 0.396,0.333 10 false F 2.01,2.917 2.49,3.25 0.479,0.333 10 false VS 0.844,2.917 1.51,3.25 0.667,0.333 10 false GND 0.646,2.198 1.313,2.531 0.667,0.333 10 false a9
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a9-2 (VS) - Body ground Power switch on (IG) Below 1 V
a9-1 (GND) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

17.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

NG

21.CHECK FLOOR WIRE (SHORT TO B+)
17.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
a.
C284678C07
0.531,2.156 0.896,2.406 0.365,0.25 1,2.917 1.438,2.417 false 2.083,2.917 1.667,2.417 false 0.427,0.969 0.76,1.219 0.333,0.25 10 false *1 2.667,0.677 3.063,1.01 0.396,0.333 10 false *2 0.354,1.74 0.75,2.156 0.396,0.417 10 false *a 2.198,0.969 2.594,1.302 0.396,0.333 10 false A 1.927,0.979 2.323,1.313 0.396,0.333 10 false B 1.583,0.979 1.979,1.313 0.396,0.333 10 false C 1.417,0.979 1.813,1.313 0.396,0.333 10 false D 1.073,0.979 1.469,1.313 0.396,0.333 10 false E 0.802,0.969 1.198,1.302 0.396,0.333 10 false F 2.01,2.917 2.49,3.25 0.479,0.333 10 false VS 0.844,2.917 1.51,3.25 0.667,0.333 10 false GND 0.646,2.198 1.313,2.531 0.667,0.333 10 false a9
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a9-2 (VS) - Body ground Always 1 MΩ or higher
a9-1 (GND) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK DTC

NG

20.CHECK FLOOR WIRE (SHORT TO GROUND)
18.CHECK DTC
a.
C284676C01
0.531,1.229 0.906,1.531 0.375,0.302 10 false *1 2.635,0.938 2.979,1.26 0.344,0.323 10 false *2 2.198,1.219 2.542,1.542 0.344,0.323 10 false A 2.042,1.229 2.385,1.552 0.344,0.323 10 false B 1.594,1.229 1.938,1.552 0.344,0.323 10 false C 1.438,1.229 1.781,1.552 0.344,0.323 10 false D 0.99,1.229 1.333,1.552 0.344,0.323 10 false E 0.833,1.229 1.177,1.552 0.344,0.323 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly


Connect the connectors to the airbag ECU assembly and seat position airbag sensor.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

19.CHECK SEAT POSITION AIRBAG SENSOR
19.CHECK SEAT POSITION AIRBAG SENSOR
a.
C284676C01
0.531,1.229 0.906,1.531 0.375,0.302 10 false *1 2.635,0.938 2.979,1.26 0.344,0.323 10 false *2 2.198,1.219 2.542,1.542 0.344,0.323 10 false A 2.042,1.229 2.385,1.552 0.344,0.323 10 false B 1.594,1.229 1.938,1.552 0.344,0.323 10 false C 1.438,1.229 1.781,1.552 0.344,0.323 10 false D 0.99,1.229 1.333,1.552 0.344,0.323 10 false E 0.833,1.229 1.177,1.552 0.344,0.323 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Replace the seat position airbag sensor with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Restore the seat position airbag sensor that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

NG

20.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C348591C01
0.927,2.146 1.281,2.396 0.354,0.25 1.958,0.938 1.958,0.521 1.958,0.521 1.792,0.521 false 1.167,0.938 1.167,0.521 1.167,0.521 1,0.521 false 1.406,2.823 1.719,2.344 false 2.375,2.823 2.094,2.344 false 0.271,0.885 0.698,1.156 0.427,0.271 10 false *1 2.854,0.646 3.219,1.073 0.365,0.427 10 false *2 0.844,0.438 1.354,0.865 0.51,0.427 10 false *3 1.635,0.438 2.073,0.802 0.438,0.365 10 false *4 0.74,1.635 1.156,1.927 0.417,0.292 10 false *a 0.99,2.198 1.406,2.49 0.417,0.292 10 false Ma3 2.25,2.833 2.667,3.125 0.417,0.292 10 false RSP+ 1.26,2.833 1.677,3.125 0.417,0.292 10 false RSP- 2.458,0.896 2.823,1.323 0.365,0.427 10 false A 2.146,0.896 2.51,1.323 0.365,0.427 10 false B 1.677,0.896 2.042,1.323 0.365,0.427 10 false C 1.365,0.896 1.729,1.323 0.365,0.427 10 false D 0.896,0.896 1.26,1.323 0.365,0.427 10 false E 0.594,0.896 0.958,1.323 0.365,0.427 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the floor wire connector from the front seat wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ma3-2 (RSP+) - Body ground Always 1 MΩ or higher
Ma3-1 (RSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (SHORT TO B+)
a.
C348591C01
0.927,2.146 1.281,2.396 0.354,0.25 1.958,0.938 1.958,0.521 1.958,0.521 1.792,0.521 false 1.167,0.938 1.167,0.521 1.167,0.521 1,0.521 false 1.406,2.823 1.719,2.344 false 2.375,2.823 2.094,2.344 false 0.271,0.885 0.698,1.156 0.427,0.271 10 false *1 2.854,0.646 3.219,1.073 0.365,0.427 10 false *2 0.844,0.438 1.354,0.865 0.51,0.427 10 false *3 1.635,0.438 2.073,0.802 0.438,0.365 10 false *4 0.74,1.635 1.156,1.927 0.417,0.292 10 false *a 0.99,2.198 1.406,2.49 0.417,0.292 10 false Ma3 2.25,2.833 2.667,3.125 0.417,0.292 10 false RSP+ 1.26,2.833 1.677,3.125 0.417,0.292 10 false RSP- 2.458,0.896 2.823,1.323 0.365,0.427 10 false A 2.146,0.896 2.51,1.323 0.365,0.427 10 false B 1.677,0.896 2.042,1.323 0.365,0.427 10 false C 1.365,0.896 1.729,1.323 0.365,0.427 10 false D 0.896,0.896 1.26,1.323 0.365,0.427 10 false E 0.594,0.896 0.958,1.323 0.365,0.427 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the floor wire connector from the front seat wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Ma3-2 (RSP+) - Body ground Power switch on (IG) Below 1 V
Ma3-1 (RSP-) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE

22.CHECK FLOOR WIRE (SHORT)
a.
C348591C01
0.927,2.146 1.281,2.396 0.354,0.25 1.958,0.938 1.958,0.521 1.958,0.521 1.792,0.521 false 1.167,0.938 1.167,0.521 1.167,0.521 1,0.521 false 1.406,2.823 1.719,2.344 false 2.375,2.823 2.094,2.344 false 0.271,0.885 0.698,1.156 0.427,0.271 10 false *1 2.854,0.646 3.219,1.073 0.365,0.427 10 false *2 0.844,0.438 1.354,0.865 0.51,0.427 10 false *3 1.635,0.438 2.073,0.802 0.438,0.365 10 false *4 0.74,1.635 1.156,1.927 0.417,0.292 10 false *a 0.99,2.198 1.406,2.49 0.417,0.292 10 false Ma3 2.25,2.833 2.667,3.125 0.417,0.292 10 false RSP+ 1.26,2.833 1.677,3.125 0.417,0.292 10 false RSP- 2.458,0.896 2.823,1.323 0.365,0.427 10 false A 2.146,0.896 2.51,1.323 0.365,0.427 10 false B 1.677,0.896 2.042,1.323 0.365,0.427 10 false C 1.365,0.896 1.729,1.323 0.365,0.427 10 false D 0.896,0.896 1.26,1.323 0.365,0.427 10 false E 0.594,0.896 0.958,1.323 0.365,0.427 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the floor wire connector from the front seat wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ma3-2 (RSP+) - Ma3-1 (RSP-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE

23.CHECK FLOOR WIRE (OPEN)
a.
C348590C01
0.604,3.427 0.979,3.646 0.375,0.219 0.563,0.49 0.906,0.708 0.344,0.219 2.75,0.875 2.333,0.875 false 2.385,0.5 2.031,0.75 false 2.375,1.25 2.021,0.99 false 1.458,3.677 1.156,4.146 false 1.833,3.677 2.115,4.156 false 1.917,2.458 1.917,2.042 1.917,2.042 1.75,2.042 false 1.146,2.469 1.146,2.052 1.146,2.052 0.979,2.052 false 0.281,2.448 0.677,2.76 0.396,0.313 10 false *1 2.802,2.135 3.156,2.542 0.354,0.406 10 false *2 0.833,1.979 1.271,2.365 0.438,0.385 10 false *3 1.615,1.969 2.021,2.313 0.406,0.344 10 false *4 2.781,0.792 3.219,1.146 0.438,0.354 10 false *5 0.542,0.146 0.958,0.667 0.417,0.521 10 false *a 0.365,3.115 0.781,3.417 0.417,0.302 10 false *b 0.615,0.521 1.052,0.875 0.438,0.354 10 false M45 2.417,0.417 2.875,0.771 0.458,0.354 10 false RSP+ 2.417,1.188 2.854,1.542 0.438,0.354 10 false RSP- 2,4.167 2.583,4.51 0.583,0.344 10 false RSP+ 1,4.167 1.458,4.531 0.458,0.365 10 false RSP- 0.667,3.458 1.104,3.813 0.438,0.354 10 false Ma3 2.427,2.438 2.781,2.844 0.354,0.406 10 false A 2.125,2.438 2.479,2.844 0.354,0.406 10 false B 1.656,2.438 2.01,2.844 0.354,0.406 10 false C 1.344,2.438 1.698,2.844 0.354,0.406 10 false D 0.875,2.438 1.229,2.844 0.354,0.406 10 false E 0.563,2.438 0.917,2.844 0.354,0.406 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag ECU Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the floor wire connector from the front seat wire RH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ma3-2 (RSP+) - Ma3-1 (RSP-) Always Below 1 Ω



c.

Disconnect the service wire from the connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE