Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225221 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1782  Rear Occupant Classification Sensor LH Circuit Malfunction  


DESCRIPTION

The rear occupant classification sensor LH circuit consists of the occupant detection ECU and rear occupant classification sensor LH.

DTC B1782 is stored when a malfunction is detected in the rear occupant classification sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1782 Rear Occupant Classification Sensor LH Circuit Malfunction
·

The occupant detection ECU detects a line short, short to ground or B+, or an open in the rear occupant classification sensor LH circuit.

·

Rear occupant classification sensor LH malfunction

·

Occupant detection ECU malfunction


·

Front seat wire RH

·

Rear occupant classification sensor LH (Front seat adjuster assembly RH)*

·

Occupant detection ECU



*: The rear occupant classification sensor LH is built into the front seat adjuster assembly RH.


WIRING DIAGRAM

C239232E61
0.552,3.063 3.677,3.573 3.125,0.51 10 false Rear Occupant Classification Sensor LH 5.333,3.063 7,3.406 1.667,0.344 10 false Occupant Detection ECU 5.375,0.625 5.875,0.948 0.5,0.323 10 false SVC3 5.375,1.5 5.833,1.802 0.458,0.302 10 false SIG3 5.375,2.365 5.927,2.74 0.552,0.375 10 false SGD3 1.844,0.521 2.188,1.021 0.344,0.5 10 false 1 1.844,1.396 2.01,1.594 0.167,0.198 10 false 2 1.844,2.271 2.146,2.635 0.302,0.365 10 false 3 5.229,0.531 5.448,0.74 0.219,0.208 10 false 2 5.229,1.406 5.406,1.615 0.177,0.208 10 false 4 5.229,2.26 5.531,2.542 0.302,0.281 10 false 6 5.344,2.906 5.854,3.26 0.51,0.354 10 false a10 0.552,2.906 1.021,3.271 0.469,0.365 10 false a14 1.469,0.615 2.25,1.021 0.781,0.406 10 false SVC 1.531,1.479 2.073,1.823 0.542,0.344 10 false SIG 1.469,2.354 2.094,2.646 0.625,0.292 10 false SGD

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1782 is output, perform troubleshooting for this DTC first.

·

If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.

·

In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.



PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Check that the connectors are properly connected to the occupant detection ECU and rear occupant classification sensor LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the occupant detection ECU and rear occupant classification sensor LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)

NG

REPLACE FRONT SEAT WIRE RH

2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)
a.
C290338C13
0.594,2.177 0.979,2.427 0.385,0.25 1.24,2.823 1.594,2.344 false 1.542,0.531 1.542,0.198 1.542,0.198 1.375,0.198 false 1.885,2.833 1.885,2.354 false 2.49,2.823 2.167,2.354 false 0.604,0.51 1.021,0.833 0.417,0.323 10 false *1 2.406,0.677 2.74,1.083 0.333,0.406 10 false *2 1.229,0.125 1.708,0.531 0.479,0.406 10 false *3 0.406,1.615 0.906,2.021 0.5,0.406 10 false *a 1.021,2.833 1.438,3.167 0.417,0.333 10 false SVC3 1.74,2.833 2.156,3.167 0.417,0.333 10 false SIG3 2.323,2.833 2.74,3.167 0.417,0.333 10 false SGD3 0.688,2.219 1.188,2.625 0.5,0.406 10 false a10 2.104,0.531 2.438,0.938 0.333,0.406 10 false A 1.813,0.531 2.146,0.938 0.333,0.406 10 false B 1.198,0.531 1.531,0.938 0.333,0.406 10 false C 0.917,0.531 1.25,0.938 0.333,0.406 10 false D
*1 Rear Occupant Classification Sensor LH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a10-2 (SVC3) - Body ground Power switch on (IG) Below 1 V
a10-4 (SIG3) - Body ground Power switch on (IG) Below 1 V
a10-6 (SGD3) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

3.CHECK FRONT SEAT WIRE RH (OPEN)

NG

12.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
3.CHECK FRONT SEAT WIRE RH (OPEN)
a.
C295787C05
0.854,0.594 1.208,0.844 0.354,0.25 0.5,3.5 0.854,3.719 0.354,0.219 2.135,1.24 2.135,0.75 false 2.073,3.042 2.385,3.042 false 2.052,4.125 2.385,4.125 false 1.833,3.604 2.385,3.604 false 1.531,2.531 1.531,2.115 false 1.531,1.229 1.844,0.75 false 2.76,1.229 2.427,0.75 false 0.917,3.083 1.615,3.563 false 0.99,4.073 1.458,3.625 false 2.417,2.125 2.813,2.448 0.396,0.323 10 false *2 1.458,2.531 1.771,2.781 0.313,0.25 10 false *3 0.625,0.26 0.958,0.594 0.333,0.333 10 false *a 0.333,2.927 0.75,3.25 0.417,0.323 10 false *b 0.615,1.958 1.01,2.281 0.396,0.323 10 false *1 2.417,2.958 2.75,3.281 0.333,0.323 10 false *4 2.417,4.042 2.75,4.365 0.333,0.323 10 false *4 2.427,3.521 2.854,3.885 0.427,0.365 10 false SGD 0.646,3.01 1.063,3.354 0.417,0.344 10 false SIG 0.667,4 1.115,4.365 0.448,0.365 10 false SVC 1.313,1.24 1.813,1.563 0.5,0.323 10 false SVC3 1.979,1.24 2.479,1.563 0.5,0.323 10 false SIG3 2.594,1.24 3.094,1.563 0.5,0.323 10 false SGD3 0.927,0.635 1.427,0.958 0.5,0.323 10 false a10 2.094,1.979 2.49,2.302 0.396,0.323 10 false A 1.813,1.979 2.208,2.302 0.396,0.323 10 false B 1.188,1.969 1.583,2.292 0.396,0.323 10 false C 0.906,1.969 1.302,2.292 0.396,0.323 10 false D 0.573,3.531 0.906,3.854 0.333,0.323 10 false a14
*1 Rear Occupant Classification Sensor LH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*4 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Rear Occupant Classification Sensor LH)


Using service wires, connect terminals 1 (SVC) and 3 (SGD), and terminals 2 (SIG) and 3 (SGD) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a10-2 (SVC3) - a10-6 (SGD3) Always Below 1 Ω
a10-4 (SIG3) - a10-6 (SGD3) Always Below 1 Ω



c.

Disconnect the service wires from connector C.


Result:
Proceed to
OK
NG



OK

4.CHECK FRONT SEAT WIRE RH (SHORT)

NG

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH (SHORT)
a.
C290338C13
0.594,2.177 0.979,2.427 0.385,0.25 1.24,2.823 1.594,2.344 false 1.542,0.531 1.542,0.198 1.542,0.198 1.375,0.198 false 1.885,2.833 1.885,2.354 false 2.49,2.823 2.167,2.354 false 0.604,0.51 1.021,0.833 0.417,0.323 10 false *1 2.406,0.677 2.74,1.083 0.333,0.406 10 false *2 1.229,0.125 1.708,0.531 0.479,0.406 10 false *3 0.406,1.615 0.906,2.021 0.5,0.406 10 false *a 1.021,2.833 1.438,3.167 0.417,0.333 10 false SVC3 1.74,2.833 2.156,3.167 0.417,0.333 10 false SIG3 2.323,2.833 2.74,3.167 0.417,0.333 10 false SGD3 0.688,2.219 1.188,2.625 0.5,0.406 10 false a10 2.104,0.531 2.438,0.938 0.333,0.406 10 false A 1.813,0.531 2.146,0.938 0.333,0.406 10 false B 1.198,0.531 1.531,0.938 0.333,0.406 10 false C 0.917,0.531 1.25,0.938 0.333,0.406 10 false D
*1 Rear Occupant Classification Sensor LH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a10-2 (SVC3) - a10-6 (SGD3) Always 1 MΩ or higher
a10-4 (SIG3) - a10-6 (SGD3) Always 1 MΩ or higher
a10-2 (SVC3) - a10-4 (SIG3) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)
a.
C290338C13
0.594,2.177 0.979,2.427 0.385,0.25 1.24,2.823 1.594,2.344 false 1.542,0.531 1.542,0.198 1.542,0.198 1.375,0.198 false 1.885,2.833 1.885,2.354 false 2.49,2.823 2.167,2.354 false 0.604,0.51 1.021,0.833 0.417,0.323 10 false *1 2.406,0.677 2.74,1.083 0.333,0.406 10 false *2 1.229,0.125 1.708,0.531 0.479,0.406 10 false *3 0.406,1.615 0.906,2.021 0.5,0.406 10 false *a 1.021,2.833 1.438,3.167 0.417,0.333 10 false SVC3 1.74,2.833 2.156,3.167 0.417,0.333 10 false SIG3 2.323,2.833 2.74,3.167 0.417,0.333 10 false SGD3 0.688,2.219 1.188,2.625 0.5,0.406 10 false a10 2.104,0.531 2.438,0.938 0.333,0.406 10 false A 1.813,0.531 2.146,0.938 0.333,0.406 10 false B 1.198,0.531 1.531,0.938 0.333,0.406 10 false C 0.917,0.531 1.25,0.938 0.333,0.406 10 false D
*1 Rear Occupant Classification Sensor LH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a10-2 (SVC3) - Body ground Always 1 MΩ or higher
a10-4 (SIG3) - Body ground Always 1 MΩ or higher
a10-6 (SGD3) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK DTC

NG

REPLACE FRONT SEAT WIRE RH

6.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and rear occupant classification sensor LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 394

d.

Clear the DTCs stored in the airbag ECU assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 10 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 394
OK:

DTC B1782 is not output.


HINT:

Codes other than DTC B1782 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

7.CHECK OCCUPANT DETECTION ECU
7.CHECK OCCUPANT DETECTION ECU
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Replace the occupant detection ECU with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 394

e.

Clear the DTCs stored in the airbag ECU assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 10 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 394
OK:

DTC B1782 is not output.


HINT:

Codes other than DTC B1782 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Restore the occupant detection ECU that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL


Result:
Proceed to
OK
NG



OK

8.REPLACE OCCUPANT DETECTION ECU

NG

10.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
8.REPLACE OCCUPANT DETECTION ECU
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Replace the occupant detection ECU with a new one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL


d.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

9.PERFORM ZERO POINT CALIBRATION
9.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform Zero Point Calibration.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END

10.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Replace the front seat adjuster assembly RH.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL


d.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ZERO POINT CALIBRATION
11.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform Zero Point Calibration.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END

12.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
a.

Replace the front seat adjuster assembly RH.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL

NOTICE:

Replace the front seat wire RH at the same time.


HINT:

When the front seat wire RH has a short to B+, the rear occupant classification sensor LH will be damaged. Therefore, replace the front seat wire RH and the front seat adjuster assembly RH, which includes the rear occupant classification sensor LH.



b.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

13.PERFORM ZERO POINT CALIBRATION
13.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform Zero Point Calibration.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END