The front occupant classification sensor LH circuit consists of the occupant detection ECU and front occupant classification sensor LH.
DTC B1780 is stored when a malfunction is detected in the front occupant classification sensor LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1780 | Front Occupant Classification Sensor LH Circuit Malfunction | ·
The occupant detection ECU detects a line short, short to ground or B+, or an open in the front occupant classification sensor LH circuit. ·
Front occupant classification sensor LH malfunction ·
Occupant detection ECU malfunction |
·
Front seat wire RH ·
Front occupant classification sensor LH (Front seat adjuster assembly RH)* ·
Occupant detection ECU |
*: The front occupant classification sensor LH is built into the front seat adjuster assembly RH.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When DTC B1650/32 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1780 is output, perform troubleshooting for this DTC first.
If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.
In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check that the connectors are properly connected to the occupant detection ECU and front occupant classification sensor LH.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the occupant detection ECU and front occupant classification sensor LH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Occupant Classification Sensor LH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *a | Front view of wire harness connector
(to Occupant Detection ECU) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a10-1 (SVC1) - Body ground | Power switch on (IG) | Below 1 V |
| a10-3 (SIG1) - Body ground | Power switch on (IG) | Below 1 V |
| a10-5 (SGD1) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Occupant Classification Sensor LH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Occupant Detection ECU) |
| *b | Front view of wire harness connector
(to Front Occupant Classification Sensor LH) |
Using service wires, connect terminals 1 (SVC) and 3 (SGD), and terminals 2 (SIG) and 3 (SGD) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a10-1 (SVC1) - a10-5 (SGD1) | Always | Below 1 Ω |
| a10-3 (SIG1) - a10-5 (SGD1) | Always | Below 1 Ω |
Disconnect the service wires from connector C.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Occupant Classification Sensor LH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *a | Front view of wire harness connector
(to Occupant Detection ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a10-1 (SVC1) - a10-5 (SGD1) | Always | 1 MΩ or higher |
| a10-3 (SIG1) - a10-5 (SGD1) | Always | 1 MΩ or higher |
| a10-1 (SVC1) - a10-3 (SIG1) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Occupant Classification Sensor LH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *a | Front view of wire harness connector
(to Occupant Detection ECU) |
Measure the resistance according to value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a10-1 (SVC1) - Body ground | Always | 1 MΩ or higher |
| a10-3 (SIG1) - Body ground | Always | 1 MΩ or higher |
| a10-5 (SGD1) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connectors to the occupant detection ECU and front occupant classification sensor LH.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in the occupant detection ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
Clear the DTCs stored in the airbag ECU assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 10 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
DTC B1780 is not output.
Codes other than DTC B1780 may be output at this time, but they are not related to this check.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Replace the occupant detection ECU with a known good one.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL
Perform the following inspection using known good parts from another vehicle if possible.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in the occupant detection ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
Clear the DTCs stored in the airbag ECU assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 10 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
DTC B1780 is not output.
Codes other than DTC B1780 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Restore the occupant detection ECU that was installed for testing to its original location.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Replace the occupant detection ECU with a new one.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL
Connect the cable to the negative (-) auxiliary battery terminal.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform Zero Point Calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Tester Display |
|---|
| Zero Point Calibration |
| Proceed to |
|---|
| NEXT |
NEXT
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Replace the front seat adjuster assembly RH.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
Connect the cable to the negative (-) auxiliary battery terminal.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform Zero Point Calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Tester Display |
|---|
| Zero Point Calibration |
| Proceed to |
|---|
| NEXT |
NEXT
Replace the front seat adjuster assembly RH.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
Replace the front seat wire RH at the same time.
When the front seat wire RH has a short to B+, the front occupant classification sensor LH will be damaged. Therefore, replace the front seat wire RH and the front seat adjuster assembly RH, which includes the front occupant classification sensor LH.
Connect the cable to the negative (-) auxiliary battery terminal.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform Zero Point Calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Tester Display |
|---|
| Zero Point Calibration |
| Proceed to |
|---|
| NEXT |
NEXT