Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225222 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the spiral cable sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Removal/installation of the spiral cable with sensor sub-assembly Steering angle neutral point (Initialize intelligent clearance sonar system)
·

Intelligent clearance sonar system

·

Simple intelligent parking assist system

·

Parking assist monitor system


(Click here)
Steering angle setting Parking assist monitor system (Click here)

PROCEDURE

Hide 45100 1.REMOVE STEERING WHEEL ASSEMBLY

Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84307 3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

a.
B432309C01
0.833,0.656 1.417,0.656 1.417,0.656 1.417,0.875 true 0.615,0.573 0.823,0.802 0.208,0.229 10 true *a
*a Flat Cable


Check the flat cable shown in the illustration.

If the flat cable shown in the illustration is not visible, it is possible that the spiral cable with sensor sub-assembly is broken. Replace the spiral cable with sensor sub-assembly with a new one.


Hide 45024 4.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY

Hide 45286B 5.REMOVE UPPER STEERING COLUMN COVER

Hide 84307 6.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the power switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the front wheels are aligned facing straight ahead.


d.
B432312C01
0.917,2.365 1.229,2.365 true 1.26,2.271 1.49,2.49 0.229,0.219 10 true *a
*a Slider


Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



e.

Disconnect the other connectors from the spiral cable with sensor sub-assembly.


f.
B434257

Disengage the 3 claws to remove the spiral cable with sensor sub-assembly.


Hide 84306 7.REMOVE SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly or the steering sensor.

·

Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in the center position of the steering sensor becoming misaligned. Therefore, make sure to use the lock pin provided with a new spiral cable sub-assembly when removing the steering sensor from the spiral cable sub-assembly.

·


a.
C238437

Install the lock pin to the steering sensor.

NOTICE:
·

Use the lock pin provided with a new spiral cable sub-assembly.

·

Do not remove the lock pin before installing the steering sensor to the spiral cable sub-assembly.




b.
B279788C05
0.948,0.74 1.844,0.365 true 0.99,1.271 1.823,1.76 true 1.844,0.25 2.01,0.469 0.167,0.219 10 false *a 1.844,1.688 2.042,1.896 0.198,0.208 10 false *a
*a Guide


Disengage the 6 claws and 2 pins, and remove the spiral cable sub-assembly from the steering sensor.

NOTICE:

Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.