The side collision sensor RH circuit (bus 1) consists of the airbag ECU assembly, door side airbag sensor RH, side airbag sensor assembly RH and rear airbag sensor RH.
The door side airbag sensor RH, side airbag sensor assembly RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1622/81 | Lost communication with Side Airbag Sensor RH | ·
The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1). ·
Side airbag sensor assembly RH malfunction ·
Rear airbag sensor RH malfunction ·
Door side airbag sensor RH malfunction ·
Airbag ECU assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor assembly RH ·
Rear airbag sensor RH ·
Door side airbag sensor RH ·
Airbag ECU assembly |
Does not apply to test/check mode |
| B1623/81 | Side Airbag Sensor Assembly RH Initialization Incomplete | ·
The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1). ·
Side airbag sensor assembly RH malfunction ·
Rear airbag sensor RH malfunction ·
Door side airbag sensor RH malfunction ·
Airbag ECU assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor assembly RH ·
Rear airbag sensor RH ·
Door side airbag sensor RH ·
Airbag ECU assembly |
Does not apply to test/check mode |
| B1632/81 | Lost Communication with Rear Airbag Sensor RH | ·
The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1). ·
Side airbag sensor assembly RH malfunction ·
Rear airbag sensor RH malfunction ·
Door side airbag sensor RH malfunction ·
Airbag ECU assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor assembly RH ·
Rear airbag sensor RH ·
Door side airbag sensor RH ·
Airbag ECU assembly |
Does not apply to test/check mode |
| B1633/81 | Rear Airbag Sensor Assembly RH Initialization Incomplete | ·
The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1). ·
Side airbag sensor assembly RH malfunction ·
Rear airbag sensor RH malfunction ·
Door side airbag sensor RH malfunction ·
Airbag ECU assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor assembly RH ·
Rear airbag sensor RH ·
Door side airbag sensor RH ·
Airbag ECU assembly |
Does not apply to test/check mode |
| B1642/81 | Lost Communication with Side Satellite Sensor Bus RH | ·
The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1). ·
Side airbag sensor assembly RH malfunction ·
Rear airbag sensor RH malfunction ·
Door side airbag sensor RH malfunction ·
Airbag ECU assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor assembly RH ·
Rear airbag sensor RH ·
Door side airbag sensor RH ·
Airbag ECU assembly |
Does not apply to test/check mode |
| B1643/81 | Side Satellite Sensor Bus RH Initialization Incomplete | ·
The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1). ·
Side airbag sensor assembly RH malfunction ·
Rear airbag sensor RH malfunction ·
Door side airbag sensor RH malfunction ·
Airbag ECU assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor assembly RH ·
Rear airbag sensor RH ·
Door side airbag sensor RH ·
Airbag ECU assembly |
Does not apply to test/check mode |
| B166D/81 | Lost Communication with Front Door Pressure Sensor RH | ·
The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1). ·
Side airbag sensor assembly RH malfunction ·
Rear airbag sensor RH malfunction ·
Door side airbag sensor RH malfunction ·
Airbag ECU assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor assembly RH ·
Rear airbag sensor RH ·
Door side airbag sensor RH ·
Airbag ECU assembly |
Does not apply to test/check mode |
| B166E/81 | Front Door Pressure Sensor RH Initialization Incomplete | ·
The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1). ·
Side airbag sensor assembly RH malfunction ·
Rear airbag sensor RH malfunction ·
Door side airbag sensor RH malfunction ·
Airbag ECU assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor assembly RH ·
Rear airbag sensor RH ·
Door side airbag sensor RH ·
Airbag ECU assembly |
Does not apply to test/check mode |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Check for current DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.
Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1643, B166D, B166E and 81 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| Current DTC B1642, B1643 or 81 is output. | A |
| Current DTC B1623 is output. | B |
| Current DTC B1633 is output. | C |
| Current DTC B166D or B166E is output. | D |
| Current DTC B1622 is output. | E |
| Current DTC B1632 is output. | F |
| Current DTCs B1622, B1623, B1632, B1633, B1642, B1643, B166D, B166E and 81 are not output. | G |
A
B
C
D
E
F
G
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly RH, rear airbag sensor RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly RH, rear airbag sensor RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/o Passenger Airbag ON/OFF Indicator:
Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
w/ Passenger Airbag ON/OFF Indicator:
Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Side Airbag Sensor Assembly RH | *2 | Airbag ECU Assembly |
| *3 | Floor Wire | *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
*b | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-4 (BBR+) - M50-3 (BBR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-4 (BBR+) - M50-3 (BBR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-4 (BBR+) - Body ground | Power switch on (IG) | Below 1 V |
| M50-3 (BBR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| M50-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - M50-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - M50-2 (BCR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - Body ground | Power switch on (IG) | Below 1 V |
| M50-2 (BCR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| M50-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Service Wire |
| *a | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Connect the connectors that link the floor wire and front door wire RH.
Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - I6-1 (BDR-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - I6-1 (BDR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - Body ground | Power switch on (IG) | Below 1 V |
| I6-1 (BDR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - Body ground | Always | 1 MΩ or higher |
| I6-1 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag ECU Assembly |
Connect the connectors to the rear airbag sensor RH, door side airbag sensor RH and airbag ECU assembly.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1642, B1643 or 81 is output. | A |
| DTC B1647, B1648 or 82 is output. | B |
| DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR(for Center Pillar)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor Assembly RH |
Interchange the rear airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1642, B1643 or 81 is output. | A |
| DTC B1647, B1648 or 82 is output. | B |
| DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Door Side Airbag Sensor LH |
| *2 | Rear Airbag Sensor RH |
Interchange the door side airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1642, B1643 or 81 is output. | A |
| DTC B1647, B1648 or 82 is output. | B |
| DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR(for Front Door)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - Body ground | Always | 1 MΩ or higher |
| IM1-40 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - Body ground | Power switch on (IG) | Below 1 V |
| IM1-40 (BDR-) - Body ground | Power switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - IM1-40 (BDR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
The service wire has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - IM1-40 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for history DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than history DTC B1622 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| History DTC B1622 is not output. | A |
| History DTC B1622 is output. | B |
A
B
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly RH, rear airbag sensor RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly RH, rear airbag sensor RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/o Passenger Airbag ON/OFF Indicator:
Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
w/ Passenger Airbag ON/OFF Indicator:
Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Side Airbag Sensor Assembly RH | *2 | Airbag ECU Assembly |
| *3 | Floor Wire | *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
*b | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-4 (BBR+) - M50-3 (BBR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-4 (BBR+) - M50-3 (BBR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-4 (BBR+) - Body ground | Power switch on (IG) | Below 1 V |
| M50-3 (BBR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag ECU Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| M50-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - M50-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - M50-2 (BCR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - Body ground | Power switch on (IG) | Below 1 V |
| M50-2 (BCR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| M50-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Service Wire |
| *a | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Connect the connectors that link the floor wire and front door wire RH.
Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - I6-1 (BDR-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - I6-1 (BDR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - Body ground | Power switch on (IG) | Below 1 V |
| I6-1 (BDR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - Body ground | Always | 1 MΩ or higher |
| I6-1 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag ECU Assembly |
Connect the connectors to the rear airbag sensor RH, door side airbag sensor RH and airbag ECU assembly.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1623 is output. | A |
| DTC B1628 is output. | B |
| DTCs B1623 and B1628 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR(for Center Pillar)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - Body ground | Always | 1 MΩ or higher |
| IM1-40 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - Body ground | Power switch on (IG) | Below 1 V |
| IM1-40 (BDR-) - Body ground | Power switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - IM1-40 (BDR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
The service wire has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - IM1-40 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag ECU Assembly |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1622 is output. | A |
| DTC B1627 is output. | B |
| DTCs B1622 and B1627 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR(for Center Pillar)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Check for history DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than history DTC B1632 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| History DTC B1632 is not output. | A |
| History DTC B1632 is output. | B |
A
B
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the side airbag sensor assembly RH and rear airbag sensor RH.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the side airbag sensor assembly RH and rear airbag sensor RH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - M50-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - M50-2 (BCR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - Body ground | Power switch on (IG) | Below 1 V |
| M50-2 (BCR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M50-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| M50-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag ECU Assembly |
Connect the connector to the rear airbag sensor RH.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1633 is output. | A |
| DTC B1638 is output. | B |
| DTCs B1633 and B1638 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR(for Center Pillar)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor Assembly RH |
Interchange the rear airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1633 is output. | A |
| DTC B1638 is output. | B |
| DTCs B1633 and B1638 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor Assembly RH |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Interchange the rear airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1632 is output. | A |
| DTC B1637 is output. | B |
| DTCs B1632 and B1637 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the rear airbag sensor RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the rear airbag sensor RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Service Wire |
| *a | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Connect the connectors that link the floor wire and front door wire RH.
Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - I6-1 (BDR-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - I6-1 (BDR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - Body ground | Power switch on (IG) | Below 1 V |
| I6-1 (BDR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-2 (BDR+) - Body ground | Always | 1 MΩ or higher |
| I6-1 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor Assembly RH |
Connect the connector to the door side airbag sensor RH.
Interchange the rear airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B166D or B166E is output. | A |
| DTC B167B or B167C is output. | B |
| DTCs B166D, B166E, B167B and B167C are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Door Side Airbag Sensor LH |
| *2 | Rear Airbag Sensor RH |
Interchange the door side airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B166D or B166E is output. | A |
| DTC B167B or B167C is output. | B |
| DTCs B166D, B166E, B167B and B167C are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR(for Front Door)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - Body ground | Always | 1 MΩ or higher |
| IM1-40 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - Body ground | Power switch on (IG) | Below 1 V |
| IM1-40 (BDR-) - Body ground | Power switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - IM1-40 (BDR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
The service wire has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - IM1-40 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag ECU Assembly |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1622 is output. | A |
| DTC B1627 is output. | B |
| DTCs B1622 and B1627 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR(for Center Pillar)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor Assembly RH |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Interchange the rear airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1632 is output. | A |
| DTC B1637 is output. | B |
| DTCs B1632 and B1637 are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING