Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1627/82  Lost communication with Side Airbag Sensor LH  B1628/82  Side Airbag Sensor Assembly LH Initialization Incomplete  B1637/82  Lost Communication with Rear Airbag Sensor LH  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  B1648/82  Side Satellite Sensor Bus LH Initialization Incomplete  B167B/82  Lost Communication with Front Door Pressure Sensor LH  B167C/82  Front Door Pressure Sensor LH Initialization Incomplete  


DESCRIPTION

The side collision sensor LH circuit (bus 1) consists of the airbag ECU assembly, door side airbag sensor LH, side airbag sensor assembly LH and rear airbag sensor LH.

The door side airbag sensor LH, side airbag sensor assembly LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 1).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1627/82 Lost communication with Side Airbag Sensor LH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Side airbag sensor assembly LH malfunction

·

Rear airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

Rear airbag sensor LH

·

Door side airbag sensor LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Side airbag sensor assembly LH malfunction

·

Rear airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

Rear airbag sensor LH

·

Door side airbag sensor LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1637/82 Lost Communication with Rear Airbag Sensor LH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Side airbag sensor assembly LH malfunction

·

Rear airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

Rear airbag sensor LH

·

Door side airbag sensor LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Side airbag sensor assembly LH malfunction

·

Rear airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

Rear airbag sensor LH

·

Door side airbag sensor LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1647/82 Lost Communication with Side Satellite Sensor Bus LH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Side airbag sensor assembly LH malfunction

·

Rear airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

Rear airbag sensor LH

·

Door side airbag sensor LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1648/82 Side Satellite Sensor Bus LH Initialization Incomplete
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Side airbag sensor assembly LH malfunction

·

Rear airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

Rear airbag sensor LH

·

Door side airbag sensor LH

·

Airbag ECU assembly


Does not apply to test/check mode
B167B/82 Lost Communication with Front Door Pressure Sensor LH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Side airbag sensor assembly LH malfunction

·

Rear airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

Rear airbag sensor LH

·

Door side airbag sensor LH

·

Airbag ECU assembly


Does not apply to test/check mode
B167C/82 Front Door Pressure Sensor LH Initialization Incomplete
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Side airbag sensor assembly LH malfunction

·

Rear airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

Rear airbag sensor LH

·

Door side airbag sensor LH

·

Airbag ECU assembly


Does not apply to test/check mode

WIRING DIAGRAM

C238366E63
3.427,4.667 3.969,5.083 0.542,0.417 10 false M11 0.542,2.781 1.771,3.438 1.229,0.656 10 false Side Airbag Sensor Assembly LH 0.552,4.823 2.417,5.302 1.865,0.479 10 false Door Side Airbag Sensor LH 5.521,4.854 7.156,5.156 1.635,0.302 10 false Airbag ECU Assembly 5.51,4.688 6.573,4.896 1.063,0.208 10 false M2*1, M1*2 1.156,0.521 1.958,1.083 0.802,0.563 10 false BBL+ 1.594,0.438 2.063,0.938 0.469,0.5 10 false 4 1.177,1.104 1.813,1.604 0.635,0.5 10 false BBL- 4.885,0.438 5.865,0.823 0.979,0.385 10 false 8*1, 24*2 4.823,1 5.688,1.438 0.865,0.438 10 false 15*1, 23*2 1.594,1.01 1.948,1.448 0.354,0.438 10 false 3 1.146,3.792 1.948,4.427 0.802,0.635 10 false BDL+ 2.406,3.594 2.854,4.198 0.448,0.604 10 false 22 1.167,4.354 1.792,4.833 0.625,0.479 10 false BDL- 2.406,4.146 2.76,4.563 0.354,0.417 10 false 40 2.365,3.792 3.021,4.354 0.656,0.563 10 false JM1 2.365,4.333 2.917,4.854 0.552,0.521 10 false JM1 0.552,4.667 1.146,5.073 0.594,0.406 10 false J6 3.427,4.823 5.021,5.313 1.594,0.49 10 false Rear Airbag Sensor LH 0.542,2.625 1.115,3.094 0.573,0.469 10 false M8 3.469,3.802 4.063,4.292 0.594,0.49 10 false BDL+ 3.469,4.333 4.01,4.865 0.542,0.531 10 false BDL- 3.479,1.698 4.063,2.146 0.583,0.448 10 false BCL+ 3.469,2.302 4.031,2.729 0.563,0.427 10 false BCL- 1.146,1.688 1.708,2.083 0.563,0.396 10 false BCL+ 1.177,2.302 1.844,2.792 0.667,0.49 10 false BCL- 5.563,0.542 6.135,1 0.573,0.458 10 false BBL+ 5.563,1.115 6.021,1.656 0.458,0.542 10 false BBL- 1.594,1.604 2.063,2.271 0.469,0.667 10 false 1 1.594,2.208 2.083,2.688 0.49,0.479 10 false 2 3.292,1.604 3.75,2.073 0.458,0.469 10 false 4 3.292,2.177 3.875,2.74 0.583,0.563 10 false 3 3.313,3.698 3.771,4.135 0.458,0.438 10 false 1 3.313,4.24 3.802,4.792 0.49,0.552 10 false 2 1.594,3.698 2.021,4.323 0.427,0.625 10 false 2 1.594,4.24 2.021,4.813 0.427,0.573 10 false 1 0.219,5.198 2.969,5.521 2.75,0.323 10 false *1: w/o Passenger Airbag ON/OFF Indicator 0.219,5.5 2.969,5.823 2.75,0.323 10 false *2: w/ Passenger Airbag ON/OFF Indicator

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.

·

Codes other than current DTCs B1627, B1628, B1637, B1638, B1647, B1648, B167B, B167C and 82 may be output at this time, but they are not related to this check.




Result:
Result Proceed to
Current DTC B1647, B1648 or 82 is output. A
Current DTC B1628 is output. B
Current DTC B1638 is output. C
Current DTC B167B or B167C is output. D
Current DTC B1627 is output. E
Current DTC B1637 is output. F
Current DTCs B1627, B1628, B1637, B1638, B1647, B1648, B167B, B167C and 82 are not output. G



A

2.CHECK CONNECTORS

B

22.CHECK HISTORY DTC

C

42.CHECK HISTORY DTC

D

51.CHECK CONNECTORS

E

62.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

F

63.CHECK REAR AIRBAG SENSOR LH

G

2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly LH, rear airbag sensor LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly LH, rear airbag sensor LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

3.CHECK FLOOR WIRE (OPEN)
a.

w/o Passenger Airbag ON/OFF Indicator:

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

w/ Passenger Airbag ON/OFF Indicator:

Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



C348452C01
0.854,2.865 1.167,3.083 0.313,0.219 4.438,2.854 4.75,3.073 0.313,0.219 1.26,0.385 1.563,0.594 0.302,0.208 4.667,0.406 4.979,0.625 0.313,0.219 1.698,1.896 1.698,1.479 1.698,1.479 1.531,1.479 false 5.448,2.188 5.281,2.188 5.281,2.188 5.281,1.854 false 2.094,1.125 2.094,0.958 false 5.802,1.167 5.802,1.031 false 1.656,0.99 2.021,0.552 false 2.49,0.979 2.208,0.76 false 5.458,0.99 5.75,0.75 false 6.167,0.99 5.854,0.75 false 1.51,3.406 1.75,3.031 false 2.115,3.406 1.854,3.042 false 5.104,3.417 5.344,3.042 false 5.698,3.406 5.438,3.042 false 0.542,0.083 1,0.5 0.458,0.417 10 false *A 4.083,0.083 4.542,0.51 0.458,0.427 10 false *B 4.469,1.688 4.875,2.083 0.406,0.396 10 false *1 2.5,1.885 2.938,2.25 0.438,0.365 10 false *2 1.375,1.406 1.688,1.688 0.313,0.281 10 false *3 5.74,1.188 6.135,1.458 0.396,0.271 10 false *4 1.073,0.177 1.448,0.656 0.375,0.479 10 false *a 0.719,2.625 1.094,2.948 0.375,0.323 10 false *b 0.854,1.865 1.542,2.323 0.688,0.458 10 false *1 6.125,1.979 6.563,2.344 0.438,0.365 10 false *2 5.479,2.104 5.938,2.406 0.458,0.302 10 false *3 2.021,1.135 2.385,1.479 0.365,0.344 10 false *4 4.552,0.167 4.927,0.646 0.375,0.479 10 false *a 4.302,2.615 4.677,2.938 0.375,0.323 10 false *b 0.927,2.896 1.302,3.219 0.375,0.323 10 false M8 4.51,2.885 4.885,3.208 0.375,0.323 10 false M8 1.323,0.417 1.698,0.74 0.375,0.323 10 false M2 4.74,0.438 5.115,0.76 0.375,0.323 10 false M1 1.5,1 1.875,1.323 0.375,0.323 10 false BBL+ 2.375,1 2.75,1.323 0.375,0.323 10 false BBL- 6.042,1 6.417,1.323 0.375,0.323 10 false BBL+ 5.313,1 5.688,1.323 0.375,0.323 10 false BBL- 1.365,3.417 1.74,3.74 0.375,0.323 10 false BBL- 2.01,3.417 2.385,3.74 0.375,0.323 10 false BBL+ 5.594,3.417 5.969,3.74 0.375,0.323 10 false BBL+ 4.979,3.417 5.354,3.74 0.375,0.323 10 false BBL- 2.135,1.885 2.573,2.25 0.438,0.365 10 false A 1.854,1.885 2.292,2.25 0.438,0.365 10 false B 1.458,1.885 1.896,2.25 0.438,0.365 10 false C 1.177,1.885 1.615,2.25 0.438,0.365 10 false D 5.719,1.719 6.156,2.083 0.438,0.365 10 false A 5.438,1.719 5.875,2.083 0.438,0.365 10 false B 5.042,1.719 5.479,2.083 0.438,0.365 10 false C 4.76,1.719 5.198,2.083 0.438,0.365 10 false D
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly LH *2 Airbag ECU Assembly
*3 Floor Wire *4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-4 (BBL+) - M8-3 (BBL-) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT)
a.

Measure the resistance according to the value(s) in the table below.

C348453C01
0.906,1.677 1.229,1.885 0.323,0.208 4.469,1.667 4.802,1.885 0.333,0.219 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 false 2.24,2.25 1.979,1.865 false 1.625,2.26 1.865,1.865 false 5.823,2.25 5.563,1.865 false 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.979,1.698 1.365,2.063 0.385,0.365 10 false M8 4.552,1.698 4.938,2.063 0.385,0.365 10 false M8 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly LH *2 Airbag ECU Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M8-4 (BBL+) - M8-3 (BBL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO B+)
a.

Connect the cable to the negative (-) auxiliary battery terminal.

C348453C01
0.906,1.677 1.229,1.885 0.323,0.208 4.469,1.667 4.802,1.885 0.333,0.219 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 false 2.24,2.25 1.979,1.865 false 1.625,2.26 1.865,1.865 false 5.823,2.25 5.563,1.865 false 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.979,1.698 1.365,2.063 0.385,0.365 10 false M8 4.552,1.698 4.938,2.063 0.385,0.365 10 false M8 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly LH *2 Airbag ECU Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
- -



b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M8-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
M8-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (SHORT TO GROUND)
a.

Measure the resistance according to the value(s) in the table below.

C348453C01
0.906,1.677 1.229,1.885 0.323,0.208 4.469,1.667 4.802,1.885 0.333,0.219 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 false 2.24,2.25 1.979,1.865 false 1.625,2.26 1.865,1.865 false 5.823,2.25 5.563,1.865 false 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.979,1.698 1.365,2.063 0.385,0.365 10 false M8 4.552,1.698 4.938,2.063 0.385,0.365 10 false M8 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly LH *2 Airbag ECU Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M8-4 (BBL+) - Body ground Always 1 MΩ or higher
M8-3 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE (OPEN)
a.
C238392C22
0.469,3.542 0.833,3.792 0.365,0.25 0.917,0.552 1.219,0.781 0.302,0.229 1.823,0.708 1.49,1.031 false 1.948,0.708 2.281,1.031 false 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 false 1.646,3.667 2,4.031 false 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCL- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCL+ 0.542,3.583 0.958,3.906 0.417,0.323 10 false M11 0.99,0.583 1.281,0.906 0.292,0.323 10 false M8 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCL- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCL+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Rear Airbag Sensor LH)


Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - M8-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

8.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (SHORT)
a.
C238222C75
1.156,2.302 1.479,2.531 0.323,0.229 2.094,2.458 1.844,2.833 false 2.219,2.458 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false M8 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCL- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCL+
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - M8-2 (BCL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238222C75
1.156,2.302 1.479,2.531 0.323,0.229 2.094,2.458 1.844,2.833 false 2.219,2.458 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false M8 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCL- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCL+
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M8-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

10.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238222C75
1.156,2.302 1.479,2.531 0.323,0.229 2.094,2.458 1.844,2.833 false 2.219,2.458 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false M8 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCL- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCL+
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - Body ground Always 1 MΩ or higher
M8-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS (OPEN)

NG

REPLACE FLOOR WIRE

11.CHECK WIRE HARNESS (OPEN)
a.
C284683C14
0.792,0.573 1.167,0.813 0.375,0.24 0.521,3.625 0.865,3.865 0.344,0.24 2.333,1.083 1.917,0.667 false 1.01,4.167 1.385,3.75 false 2.042,4.167 1.625,3.75 false 1.354,1.083 1.771,0.667 false 1.844,1.302 1.844,1.094 false 0.552,2.313 0.917,2.625 0.365,0.313 10 false *1 2.74,2.333 3.063,2.75 0.323,0.417 10 false *2 1.781,1.313 2.135,1.615 0.354,0.302 10 false *3 0.635,0.167 0.979,0.583 0.344,0.417 10 false *a 0.344,3.156 0.625,3.583 0.281,0.427 10 false *b 2.396,2.333 2.719,2.75 0.323,0.417 10 false A 2.083,2.333 2.406,2.75 0.323,0.417 10 false B 1.74,2.333 2.063,2.75 0.323,0.417 10 false C 1.583,2.333 1.906,2.75 0.323,0.417 10 false D 1.24,2.323 1.563,2.74 0.323,0.417 10 false E 0.927,2.323 1.25,2.74 0.323,0.417 10 false F 1.188,1.104 1.604,1.521 0.417,0.417 10 false BDL+ 2.229,1.104 2.646,1.521 0.417,0.417 10 false BDL- 1.885,4.167 2.302,4.5 0.417,0.333 10 false BDL+ 0.844,4.167 1.26,4.604 0.417,0.438 10 false BDL- 0.854,0.615 1.271,1.031 0.417,0.417 10 false M11 0.635,3.667 1.052,4.083 0.417,0.417 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the connectors that link the floor wire and front door wire LH.


b.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - J6-1 (BDL-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK WIRE HARNESS (SHORT)

NG

21.CHECK FLOOR WIRE (OPEN)
12.CHECK WIRE HARNESS (SHORT)
a.
C284684C14
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 false 2.25,2.75 1.792,2.313 false 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.802,2.229 1.198,2.583 0.396,0.354 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - J6-1 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK WIRE HARNESS (SHORT TO B+)

NG

20.CHECK FLOOR WIRE (SHORT)
13.CHECK WIRE HARNESS (SHORT TO B+)
a.
C284684C14
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 false 2.25,2.75 1.792,2.313 false 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.802,2.229 1.198,2.583 0.396,0.354 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - Body ground Power switch on (IG) Below 1 V
J6-1 (BDL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

14.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

19.CHECK FLOOR WIRE (SHORT TO B+)
14.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C284684C14
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 false 2.25,2.75 1.792,2.313 false 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.802,2.229 1.198,2.583 0.396,0.354 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - Body ground Always 1 MΩ or higher
J6-1 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

18.CHECK FLOOR WIRE (SHORT TO GROUND)
15.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Passenger Airbag ON/OFF Indicator
*B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Connect the connectors to the rear airbag sensor LH, door side airbag sensor LH and airbag ECU assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

16.CHECK REAR AIRBAG SENSOR LH

B

C

16.CHECK REAR AIRBAG SENSOR LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly LH


Interchange the rear airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors.



A

17.CHECK DOOR SIDE AIRBAG SENSOR LH

B

C

17.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor RH
*2 Rear Airbag Sensor LH


Interchange the door side airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

18.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284682C18
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 false 1.406,2.479 1.667,3 false 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - Body ground Always 1 MΩ or higher
JM1-40 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

19.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284682C18
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 false 1.406,2.479 1.667,3 false 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - Body ground Power switch on (IG) Below 1 V
JM1-40 (BDL-) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

20.CHECK FLOOR WIRE (SHORT)
a.
C284682C18
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 false 1.406,2.479 1.667,3 false 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (OPEN)
a.
C284681C14
0.823,0.552 1.188,0.802 0.365,0.25 0.458,2.823 0.833,3.042 0.375,0.219 1.781,4.302 1.406,3.771 false 1.844,1.344 1.844,1.094 false 1.333,1.167 1.771,0.667 false 2.333,1.167 1.917,0.667 false 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 1,4.302 1.406,3.625 false 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.75,1.698 2.146,2.031 0.396,0.333 10 false *4 1.781,1.354 2.198,1.677 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDL+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDL- 0.844,4.302 1.344,4.635 0.5,0.333 10 false BDL+ 1.667,4.302 2.167,4.635 0.5,0.333 10 false BDL- 0.885,0.594 1.385,0.927 0.5,0.333 10 false M11 0.531,2.854 1.031,3.188 0.5,0.333 10 false JM1
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

22.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1627 is not output. A
History DTC B1627 is output. B



A

23.CHECK CONNECTORS

B

41.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
23.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly LH, rear airbag sensor LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly LH, rear airbag sensor LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

24.CHECK FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

24.CHECK FLOOR WIRE (OPEN)
a.

w/o Passenger Airbag ON/OFF Indicator:

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

w/ Passenger Airbag ON/OFF Indicator:

Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



C348452C01
0.854,2.865 1.167,3.083 0.313,0.219 4.438,2.854 4.75,3.073 0.313,0.219 1.26,0.385 1.563,0.594 0.302,0.208 4.667,0.406 4.979,0.625 0.313,0.219 1.698,1.896 1.698,1.479 1.698,1.479 1.531,1.479 false 5.448,2.188 5.281,2.188 5.281,2.188 5.281,1.854 false 2.094,1.125 2.094,0.958 false 5.802,1.167 5.802,1.031 false 1.656,0.99 2.021,0.552 false 2.49,0.979 2.208,0.76 false 5.458,0.99 5.75,0.75 false 6.167,0.99 5.854,0.75 false 1.51,3.406 1.75,3.031 false 2.115,3.406 1.854,3.042 false 5.104,3.417 5.344,3.042 false 5.698,3.406 5.438,3.042 false 0.542,0.083 1,0.5 0.458,0.417 10 false *A 4.083,0.083 4.542,0.51 0.458,0.427 10 false *B 4.469,1.688 4.875,2.083 0.406,0.396 10 false *1 2.5,1.885 2.938,2.25 0.438,0.365 10 false *2 1.375,1.406 1.688,1.688 0.313,0.281 10 false *3 5.74,1.188 6.135,1.458 0.396,0.271 10 false *4 1.073,0.177 1.448,0.656 0.375,0.479 10 false *a 0.719,2.625 1.094,2.948 0.375,0.323 10 false *b 0.854,1.865 1.542,2.323 0.688,0.458 10 false *1 6.125,1.979 6.563,2.344 0.438,0.365 10 false *2 5.479,2.104 5.938,2.406 0.458,0.302 10 false *3 2.021,1.135 2.385,1.479 0.365,0.344 10 false *4 4.552,0.167 4.927,0.646 0.375,0.479 10 false *a 4.302,2.615 4.677,2.938 0.375,0.323 10 false *b 0.927,2.896 1.302,3.219 0.375,0.323 10 false M8 4.51,2.885 4.885,3.208 0.375,0.323 10 false M8 1.323,0.417 1.698,0.74 0.375,0.323 10 false M2 4.74,0.438 5.115,0.76 0.375,0.323 10 false M1 1.5,1 1.875,1.323 0.375,0.323 10 false BBL+ 2.375,1 2.75,1.323 0.375,0.323 10 false BBL- 6.042,1 6.417,1.323 0.375,0.323 10 false BBL+ 5.313,1 5.688,1.323 0.375,0.323 10 false BBL- 1.365,3.417 1.74,3.74 0.375,0.323 10 false BBL- 2.01,3.417 2.385,3.74 0.375,0.323 10 false BBL+ 5.594,3.417 5.969,3.74 0.375,0.323 10 false BBL+ 4.979,3.417 5.354,3.74 0.375,0.323 10 false BBL- 2.135,1.885 2.573,2.25 0.438,0.365 10 false A 1.854,1.885 2.292,2.25 0.438,0.365 10 false B 1.458,1.885 1.896,2.25 0.438,0.365 10 false C 1.177,1.885 1.615,2.25 0.438,0.365 10 false D 5.719,1.719 6.156,2.083 0.438,0.365 10 false A 5.438,1.719 5.875,2.083 0.438,0.365 10 false B 5.042,1.719 5.479,2.083 0.438,0.365 10 false C 4.76,1.719 5.198,2.083 0.438,0.365 10 false D
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly LH *2 Airbag ECU Assembly
*3 Floor Wire *4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-4 (BBL+) - M8-3 (BBL-) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

25.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

25.CHECK FLOOR WIRE (SHORT)
a.

Measure the resistance according to the value(s) in the table below.

C348453C01
0.906,1.677 1.229,1.885 0.323,0.208 4.469,1.667 4.802,1.885 0.333,0.219 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 false 2.24,2.25 1.979,1.865 false 1.625,2.26 1.865,1.865 false 5.823,2.25 5.563,1.865 false 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.979,1.698 1.365,2.063 0.385,0.365 10 false M8 4.552,1.698 4.938,2.063 0.385,0.365 10 false M8 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly LH *2 Airbag ECU Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M8-4 (BBL+) - M8-3 (BBL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

26.CHECK FLOOR WIRE (SHORT TO B+)
a.

Connect the cable to the negative (-) auxiliary battery terminal.

C348453C01
0.906,1.677 1.229,1.885 0.323,0.208 4.469,1.667 4.802,1.885 0.333,0.219 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 false 2.24,2.25 1.979,1.865 false 1.625,2.26 1.865,1.865 false 5.823,2.25 5.563,1.865 false 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.979,1.698 1.365,2.063 0.385,0.365 10 false M8 4.552,1.698 4.938,2.063 0.385,0.365 10 false M8 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly LH *2 Airbag ECU Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
- -



b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M8-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
M8-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

27.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

27.CHECK FLOOR WIRE (SHORT TO GROUND)
a.

Measure the resistance according to the value(s) in the table below.

C348453C01
0.906,1.677 1.229,1.885 0.323,0.208 4.469,1.667 4.802,1.885 0.333,0.219 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 false 2.24,2.25 1.979,1.865 false 1.625,2.26 1.865,1.865 false 5.823,2.25 5.563,1.865 false 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.979,1.698 1.365,2.063 0.385,0.365 10 false M8 4.552,1.698 4.938,2.063 0.385,0.365 10 false M8 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly LH *2 Airbag ECU Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M8-4 (BBL+) - Body ground Always 1 MΩ or higher
M8-3 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

28.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

28.CHECK FLOOR WIRE (OPEN)
a.
C238392C22
0.469,3.542 0.833,3.792 0.365,0.25 0.917,0.552 1.219,0.781 0.302,0.229 1.823,0.708 1.49,1.031 false 1.948,0.708 2.281,1.031 false 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 false 1.646,3.667 2,4.031 false 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCL- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCL+ 0.542,3.583 0.958,3.906 0.417,0.323 10 false M11 0.99,0.583 1.281,0.906 0.292,0.323 10 false M8 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCL- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCL+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Rear Airbag Sensor LH)


Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - M8-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

29.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

29.CHECK FLOOR WIRE (SHORT)
a.
C238222C75
1.156,2.302 1.479,2.531 0.323,0.229 2.094,2.458 1.844,2.833 false 2.219,2.458 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false M8 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCL- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCL+
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - M8-2 (BCL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

30.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

30.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238222C75
1.156,2.302 1.479,2.531 0.323,0.229 2.094,2.458 1.844,2.833 false 2.219,2.458 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false M8 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCL- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCL+
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M8-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

31.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

31.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238222C75
1.156,2.302 1.479,2.531 0.323,0.229 2.094,2.458 1.844,2.833 false 2.219,2.458 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false M8 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCL- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCL+
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - Body ground Always 1 MΩ or higher
M8-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

32.CHECK WIRE HARNESS (OPEN)

NG

REPLACE FLOOR WIRE

32.CHECK WIRE HARNESS (OPEN)
a.
C284683C14
0.792,0.573 1.167,0.813 0.375,0.24 0.521,3.625 0.865,3.865 0.344,0.24 2.333,1.083 1.917,0.667 false 1.01,4.167 1.385,3.75 false 2.042,4.167 1.625,3.75 false 1.354,1.083 1.771,0.667 false 1.844,1.302 1.844,1.094 false 0.552,2.313 0.917,2.625 0.365,0.313 10 false *1 2.74,2.333 3.063,2.75 0.323,0.417 10 false *2 1.781,1.313 2.135,1.615 0.354,0.302 10 false *3 0.635,0.167 0.979,0.583 0.344,0.417 10 false *a 0.344,3.156 0.625,3.583 0.281,0.427 10 false *b 2.396,2.333 2.719,2.75 0.323,0.417 10 false A 2.083,2.333 2.406,2.75 0.323,0.417 10 false B 1.74,2.333 2.063,2.75 0.323,0.417 10 false C 1.583,2.333 1.906,2.75 0.323,0.417 10 false D 1.24,2.323 1.563,2.74 0.323,0.417 10 false E 0.927,2.323 1.25,2.74 0.323,0.417 10 false F 1.188,1.104 1.604,1.521 0.417,0.417 10 false BDL+ 2.229,1.104 2.646,1.521 0.417,0.417 10 false BDL- 1.885,4.167 2.302,4.5 0.417,0.333 10 false BDL+ 0.844,4.167 1.26,4.604 0.417,0.438 10 false BDL- 0.854,0.615 1.271,1.031 0.417,0.417 10 false M11 0.635,3.667 1.052,4.083 0.417,0.417 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the connectors that link the floor wire and front door wire LH.


b.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - J6-1 (BDL-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

33.CHECK WIRE HARNESS (SHORT)

NG

40.CHECK FLOOR WIRE (OPEN)
33.CHECK WIRE HARNESS (SHORT)
a.
C284684C14
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 false 2.25,2.75 1.792,2.313 false 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.802,2.229 1.198,2.583 0.396,0.354 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - J6-1 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

34.CHECK WIRE HARNESS (SHORT TO B+)

NG

39.CHECK FLOOR WIRE (SHORT)
34.CHECK WIRE HARNESS (SHORT TO B+)
a.
C284684C14
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 false 2.25,2.75 1.792,2.313 false 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.802,2.229 1.198,2.583 0.396,0.354 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - Body ground Power switch on (IG) Below 1 V
J6-1 (BDL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

35.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

38.CHECK FLOOR WIRE (SHORT TO B+)
35.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C284684C14
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 false 2.25,2.75 1.792,2.313 false 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.802,2.229 1.198,2.583 0.396,0.354 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - Body ground Always 1 MΩ or higher
J6-1 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

36.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

37.CHECK FLOOR WIRE (SHORT TO GROUND)
36.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Passenger Airbag ON/OFF Indicator
*B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Connect the connectors to the rear airbag sensor LH, door side airbag sensor LH and airbag ECU assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1628 is output. A
DTC B1623 is output. B
DTCs B1623 and B1628 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

37.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284682C18
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 false 1.406,2.479 1.667,3 false 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - Body ground Always 1 MΩ or higher
JM1-40 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

38.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284682C18
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 false 1.406,2.479 1.667,3 false 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - Body ground Power switch on (IG) Below 1 V
JM1-40 (BDL-) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

39.CHECK FLOOR WIRE (SHORT)
a.
C284682C18
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 false 1.406,2.479 1.667,3 false 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

40.CHECK FLOOR WIRE (OPEN)
a.
C284681C14
0.823,0.552 1.188,0.802 0.365,0.25 0.458,2.823 0.833,3.042 0.375,0.219 1.781,4.302 1.406,3.771 false 1.844,1.344 1.844,1.094 false 1.333,1.167 1.771,0.667 false 2.333,1.167 1.917,0.667 false 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 1,4.302 1.406,3.625 false 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.75,1.698 2.146,2.031 0.396,0.333 10 false *4 1.781,1.354 2.198,1.677 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDL+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDL- 0.844,4.302 1.344,4.635 0.5,0.333 10 false BDL+ 1.667,4.302 2.167,4.635 0.5,0.333 10 false BDL- 0.885,0.594 1.385,0.927 0.5,0.333 10 false M11 0.531,2.854 1.031,3.188 0.5,0.333 10 false JM1
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

41.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Passenger Airbag ON/OFF Indicator
*B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1627 is output. A
DTC B1622 is output. B
DTCs B1622 and B1627 are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

42.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1637 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1637 is not output. A
History DTC B1637 is output. B



A

43.CHECK CONNECTORS

B

50.CHECK REAR AIRBAG SENSOR LH
43.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly LH and rear airbag sensor LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly LH and rear airbag sensor LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

44.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

44.CHECK FLOOR WIRE (OPEN)
a.
C238392C22
0.469,3.542 0.833,3.792 0.365,0.25 0.917,0.552 1.219,0.781 0.302,0.229 1.823,0.708 1.49,1.031 false 1.948,0.708 2.281,1.031 false 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 false 1.646,3.667 2,4.031 false 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCL- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCL+ 0.542,3.583 0.958,3.906 0.417,0.323 10 false M11 0.99,0.583 1.281,0.906 0.292,0.323 10 false M8 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCL- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCL+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Rear Airbag Sensor LH)


Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - M8-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

45.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

45.CHECK FLOOR WIRE (SHORT)
a.
C238222C75
1.156,2.302 1.479,2.531 0.323,0.229 2.094,2.458 1.844,2.833 false 2.219,2.458 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false M8 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCL- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCL+
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - M8-2 (BCL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

46.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

46.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238222C75
1.156,2.302 1.479,2.531 0.323,0.229 2.094,2.458 1.844,2.833 false 2.219,2.458 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false M8 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCL- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCL+
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M8-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

47.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

47.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238222C75
1.156,2.302 1.479,2.531 0.323,0.229 2.094,2.458 1.844,2.833 false 2.219,2.458 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false M8 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCL- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCL+
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-1 (BCL+) - Body ground Always 1 MΩ or higher
M8-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

48.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

48.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Passenger Airbag ON/OFF Indicator
*B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Connect the connector to the rear airbag sensor LH.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1638 is output. A
DTC B1633 is output. B
DTCs B1633 and B1638 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

49.CHECK REAR AIRBAG SENSOR LH

B

C

49.CHECK REAR AIRBAG SENSOR LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly LH


Interchange the rear airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1638 is output. A
DTC B1633 is output. B
DTCs B1633 and B1638 are not output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

50.CHECK REAR AIRBAG SENSOR LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly LH


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the rear airbag sensor LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1637 is output. A
DTC B1632 is output. B
DTCs B1632 and B1637 are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

51.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the rear airbag sensor LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the rear airbag sensor LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

52.CHECK WIRE HARNESS (OPEN)

NG

REPLACE WIRE HARNESS

52.CHECK WIRE HARNESS (OPEN)
a.
C284683C14
0.792,0.573 1.167,0.813 0.375,0.24 0.521,3.625 0.865,3.865 0.344,0.24 2.333,1.083 1.917,0.667 false 1.01,4.167 1.385,3.75 false 2.042,4.167 1.625,3.75 false 1.354,1.083 1.771,0.667 false 1.844,1.302 1.844,1.094 false 0.552,2.313 0.917,2.625 0.365,0.313 10 false *1 2.74,2.333 3.063,2.75 0.323,0.417 10 false *2 1.781,1.313 2.135,1.615 0.354,0.302 10 false *3 0.635,0.167 0.979,0.583 0.344,0.417 10 false *a 0.344,3.156 0.625,3.583 0.281,0.427 10 false *b 2.396,2.333 2.719,2.75 0.323,0.417 10 false A 2.083,2.333 2.406,2.75 0.323,0.417 10 false B 1.74,2.333 2.063,2.75 0.323,0.417 10 false C 1.583,2.333 1.906,2.75 0.323,0.417 10 false D 1.24,2.323 1.563,2.74 0.323,0.417 10 false E 0.927,2.323 1.25,2.74 0.323,0.417 10 false F 1.188,1.104 1.604,1.521 0.417,0.417 10 false BDL+ 2.229,1.104 2.646,1.521 0.417,0.417 10 false BDL- 1.885,4.167 2.302,4.5 0.417,0.333 10 false BDL+ 0.844,4.167 1.26,4.604 0.417,0.438 10 false BDL- 0.854,0.615 1.271,1.031 0.417,0.417 10 false M11 0.635,3.667 1.052,4.083 0.417,0.417 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the connectors that link the floor wire and front door wire LH.


b.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - J6-1 (BDL-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

53.CHECK WIRE HARNESS (SHORT)

NG

61.CHECK FLOOR WIRE (OPEN)
53.CHECK WIRE HARNESS (SHORT)
a.
C284684C14
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 false 2.25,2.75 1.792,2.313 false 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.802,2.229 1.198,2.583 0.396,0.354 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - J6-1 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

54.CHECK WIRE HARNESS (SHORT TO B+)

NG

60.CHECK FLOOR WIRE (SHORT)
54.CHECK WIRE HARNESS (SHORT TO B+)
a.
C284684C14
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 false 2.25,2.75 1.792,2.313 false 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.802,2.229 1.198,2.583 0.396,0.354 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - Body ground Power switch on (IG) Below 1 V
J6-1 (BDL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

55.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

59.CHECK FLOOR WIRE (SHORT TO B+)
55.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C284684C14
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 false 2.25,2.75 1.792,2.313 false 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.802,2.229 1.198,2.583 0.396,0.354 10 false J6
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (BDL+) - Body ground Always 1 MΩ or higher
J6-1 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

56.CHECK REAR AIRBAG SENSOR LH

NG

58.CHECK FLOOR WIRE (SHORT TO GROUND)
56.CHECK REAR AIRBAG SENSOR LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly LH


Connect the connector to the door side airbag sensor LH.


b.

Interchange the rear airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B167B or B167C is output. A
DTC B166D or B166E is output. B
DTCs B166D, B166E, B167B and B167C are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors.



A

57.CHECK DOOR SIDE AIRBAG SENSOR LH

B

C

57.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor RH
*2 Rear Airbag Sensor LH


Interchange the door side airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B167B or B167C is output. A
DTC B166D or B166E is output. B
DTCs B166D, B166E, B167B and B167C are not output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

58.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284682C18
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 false 1.406,2.479 1.667,3 false 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - Body ground Always 1 MΩ or higher
JM1-40 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

59.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284682C18
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 false 1.406,2.479 1.667,3 false 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - Body ground Power switch on (IG) Below 1 V
JM1-40 (BDL-) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

60.CHECK FLOOR WIRE (SHORT)
a.
C284682C18
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 false 1.406,2.479 1.667,3 false 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

61.CHECK FLOOR WIRE (OPEN)
a.
C284681C14
0.823,0.552 1.188,0.802 0.365,0.25 0.458,2.823 0.833,3.042 0.375,0.219 1.781,4.302 1.406,3.771 false 1.844,1.344 1.844,1.094 false 1.333,1.167 1.771,0.667 false 2.333,1.167 1.917,0.667 false 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 1,4.302 1.406,3.625 false 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.75,1.698 2.146,2.031 0.396,0.333 10 false *4 1.781,1.354 2.198,1.677 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDL+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDL- 0.844,4.302 1.344,4.635 0.5,0.333 10 false BDL+ 1.667,4.302 2.167,4.635 0.5,0.333 10 false BDL- 0.885,0.594 1.385,0.927 0.5,0.333 10 false M11 0.531,2.854 1.031,3.188 0.5,0.333 10 false JM1
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

62.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Passenger Airbag ON/OFF Indicator
*B w/ Passenger Airbag ON/OFF Indicator
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1627 is output. A
DTC B1622 is output. B
DTCs B1622 and B1627 are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

63.CHECK REAR AIRBAG SENSOR LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly LH


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the rear airbag sensor LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1637 is output. A
DTC B1632 is output. B
DTCs B1632 and B1637 are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C