Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU
RM3210E _57 Power Source / Network _047508 POWER DISTRIBUTION _0227179 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

After the main body ECU (multiplex network body ECU) has been replaced, the automatic light control system will not operate until the engine is started.



PROCEDURE

Hide 1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NOTICE:
·

Make sure that the connecting surfaces are free of foreign matter.

·

Do not touch the main body ECU (multiplex network body ECU) connector.



a.
E336539C01
0.417,0.948 0.927,1.448 true 0.344,2.292 0.656,2.448 0.313,0.156 10 false *a 0.219,0.844 0.531,1 0.313,0.156 10 false *b
*a 20° or more
*b Housing Sidewall
V113147

Set in this Direction


Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the instrument panel junction block assembly as shown in the illustration.

HINT:

Make sure to keep the angle at 20° or more as shown in the illustration.



b.
E336542C01
0.385,0.854 0.969,1.417 true 0.177,0.729 0.49,0.885 0.313,0.156 10 false *a
*a Housing Sidewall
V113147

Slide in this Direction


Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the 2 guides.


c.
E336544C01
2.219,0.844 2.833,0.448 true 2.896,0.365 3.208,0.521 0.313,0.156 10 false *a
*a Side A
V113147

Install in this Direction


While keeping the main body ECU (multiplex network body ECU) in contact with side A of the instrument panel junction block assembly (axis of rotation), lower it as shown in the illustration.


d.
E336546C01
0.719,2.823 1.208,2.823 true 0.188,2.802 0.51,2.802 true 1.24,2.729 1.552,2.885 0.313,0.156 10 false *1 0.021,2.708 0.333,2.865 0.313,0.156 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 Main Body ECU (Multiplex Network Body ECU)
V100155

Push Area


Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).

NOTICE:
·

Make sure to press only the push area.

·

Confirm the engagement of the main body ECU (multiplex network body ECU) and instrument panel junction block assembly by listening for the click sound of the lock engaging.



HINT:

If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and instrument panel junction block assembly are flush.



Hide 82715 2.TEMPORARILY INSTALL WIRING HARNESS CLAMP BRACKET (for LHD)

a.
E336527C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw and install the wiring harness clamp bracket as shown in the illustration.


b.

Temporarily install the bolt.

HINT:

Do not fully tighten the bolt.



Hide 3.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

a.

for LHD:

i.
E336525C01
0,0 0,0 false
V113147

Install in this Direction


Connect the 2 connectors and raise the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



ii.

Engage the clamp.


iii.

Engage the clamp.


iv.

Install the instrument panel junction block assembly with main body ECU with the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


v.
E336528

Tighten the bolt to install the wiring harness clamp bracket to the instrument panel junction block assembly with main body ECU.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


vi.
E336521C01
0,0 0,0 false
V113147

Install in this Direction


Connect the 2 connectors and raise the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



vii.

Engage the clamp.


viii.

Connect each connector.



b.

for RHD:

i.
E336517C01
0,0 0,0 false
V113147

Install in this Direction


Connect the 2 connectors and pull down the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



ii.

Engage the clamp.


iii.

Engage the clamp.


iv.

Install the instrument panel junction block assembly with main body ECU with the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


v.
E336513C01
0,0 0,0 false
V113147

Install in this Direction


Connect the 2 connectors and raise the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



vi.

Engage the clamp.


vii.

Connect each connector.



Hide 55308B 4.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for LHD)

Hide 73900 5.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

Hide 82878 6.INSTALL ECU INTEGRATION BOX LH (for RHD)

Hide 55550 7.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION


Hide 55607 8.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION


Hide 9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for RHD)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION