Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0230366 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  INSTALLATION  


PROCEDURE

Hide 45130 1.INSTALL HORN BUTTON ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

w/o Passenger Airbag ON/OFF Indicator:

i.
B432390C01
1.583,0.573 1.802,0.313 1.802,0.313 2.26,0.313 true 0.885,0.365 1.313,0.365 1.313,0.365 1.531,0.635 true 0.302,0.948 1.49,0.948 true 2.031,2.938 2.271,2.938 2.271,2.938 2.5,2.573 true 0.135,0.854 0.448,1.01 0.313,0.156 10 false *a 2.281,0.229 2.5,0.448 0.219,0.219 10 true *b 1.875,2.844 2.188,3 0.313,0.156 10 false *c 0.719,0.271 0.927,0.49 0.208,0.219 10 true *d
*a Airbag Connector
*b Horn Connector
*c Airbag Connector Lock
*d Wire Harness Clamp


Engage the wire harness clamp.


ii.

Connect the airbag connector to the horn button assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



iii.

Push in the airbag connector lock to install the airbag connector.


iv.

Connect the horn connector to the horn button assembly.



d.

w/ Passenger Airbag ON/OFF Indicator:

i.
B428461C01
0.625,0.813 1.604,0.813 true 1.198,0.802 1.198,0.677 1.198,0.677 1.604,0.677 true 1.74,0.5 2.083,0.24 2.083,0.24 2.49,0.24 true 2.25,2.75 2.656,2.75 true 0.948,0.323 1.406,0.323 1.406,0.323 1.667,0.573 true 0.458,0.719 0.771,0.875 0.313,0.156 10 false *a 2.51,0.146 2.75,0.354 0.24,0.208 10 true *b 2.104,2.656 2.417,2.813 0.313,0.156 10 false *c 0.771,0.24 1.083,0.396 0.313,0.156 10 false *d
*a Airbag Connector
*b Horn Connector
*c Airbag Connector Lock
*d Wire Harness Clamp


Engage the wire harness clamp.


ii.

Connect the 2 airbag connectors to the horn button assembly.

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.

·

Be sure to connect the connectors to each corresponding color.




iii.

Push in the 2 airbag connector locks to install the 2 airbag connectors.


iv.

Connect the horn connector to the horn button assembly.



e.
B432306

Push the horn button assembly to engage the 3 hooks carefully and install the horn button assembly.

NOTICE:
·

Make sure that the hooks are securely engaged to the omega springs.

·

Make sure to engage the 2 upper hooks first.

·

Make sure that the horn button assembly is securely installed.




Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45130 3.INSPECT HORN BUTTON ASSEMBLY

a.

Make sure that the horn sounds.

If the horn does not sound, inspect the horn system.

Click hereVehicle Exterior>HORN>HORN SYSTEM>PROBLEM SYMPTOMS TABLE