Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0230367 KNEE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the lower No. 1 instrument panel airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for an LHD vehicle.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55436A 3.REMOVE INSTRUMENT PANEL FINISH PANEL END LH

Hide 55470 4.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 67914 5.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 6.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 7.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 53601 8.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55480D 9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 73900 10.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

CAUTION:
B417755C02
0.604,0.521 0.76,0.719 0.156,0.198 10 false .
V100155

Deployment Side


When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B432313

Remove the 2 bolts.


d.
B432314

Disengage the 4 claws and hook to separate the lower No. 1 instrument panel airbag assembly.

NOTICE:

When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.



e.
B432315C01
0.396,2.375 0.573,2.375 0.573,2.375 0.813,2.115 false 0.427,2.802 0.604,2.802 0.604,2.802 1,2.302 true 1.135,0.906 1.281,1.219 1.281,1.219 1.469,1.219 true 0.229,2.281 0.542,2.438 0.313,0.156 10 false *a 0.26,2.719 0.573,2.875 0.313,0.156 10 false *b 1.49,1.125 1.802,1.281 0.313,0.156 10 false *c
*a Protective Tape
*b Airbag Connector
*c Airbag Connector Lock


Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock.


f.

Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.