Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL › 2015.11–2016.08
RM3210E _58 Vehicle Interior _047504 INTERIOR PANELS / TRIM _0242035 LOWER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  LOWER INSTRUMENT PANEL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during lower instrument panel removal/installation are shown below.

Necessary Procedures after parts removed/installed/replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

PROCEDURE

Hide 1. PRECAUTION

Click hereVehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>PRECAUTION

CAUTION:
B394719

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

Hide 58910C 4.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 55436A 5.REMOVE INSTRUMENT PANEL FINISH PANEL END LH

a.
B432293C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover, disengage the 6 clips as shown in the illustration.


b.
B432297C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 3 guides to remove the instrument panel finish panel end LH as shown in the illustration.


Hide 55470 6.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

a.
B432301C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 4 clips and claw as shown in the illustration.


b.

Disconnect each connector to remove the instrument cluster finish panel garnish assembly.


Hide 67914 7.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 8.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B433139

Remove the 2 screws <F>.


b.
B433140C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw as shown in the illustration.


c.
B433142C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guide as shown in the illustration.


d.

for LHD:

i.

Disconnect the connector to remove the No. 1 instrument panel under cover sub-assembly.



e.

for RHD:

i.

Disconnect the connector.


ii.
B433138

Disengage the 2 claws to disconnect the DLC3 connector.


iii.

Disengage the clamp to remove the No. 1 instrument panel under cover sub-assembly.



Hide 53601 10.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B433150

Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.


Hide 55480D 11.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.
B433151

Remove the screw <C>.


b.
B433152C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 6 clips and 2 guides as shown in the illustration.


c.

Disconnect the connector to remove the lower instrument panel finish panel assembly.


Hide 73900 12.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 13.REMOVE COMBINATION METER ASSEMBLY

Hide 55435A 14.REMOVE INSTRUMENT PANEL FINISH PANEL END RH

a.
B442265C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover, disengage the 6 clips as shown in the illustration.


b.
B442266C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 3 guides as shown in the illustration.


c.

w/ Airbag Cut Off Switch:

i.

Disconnect the connector.



d.

Remove the instrument panel finish panel end RH.


Hide 55405B 15.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

for LHD:

i.
B442269

Remove the clip.



b.

Disengage the 6 clips and 4 guides as shown in the illustration.

B433165C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction
V100135

Order of Removal - -



c.

Disengage the 12 clips and guide as shown in the illustration.

B433168C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction



d.

Disconnect each connector.


e.

Disengage the clamp to remove the center instrument cluster finish panel sub-assembly.


Hide 16.REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)

a.
B437327

Remove the 4 bolts <B>.


b.

Disengage the 2 guides.


c.
B437328

Disengage the clamp to remove the radio tuner opening cover with bracket.


Hide 17.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)

Hide 18.REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for Navigation Receiver Type)

Hide 67913 19.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62111C 20.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 55607 21.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B433193C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 3 claws as shown in the illustration.


b.
B433195C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides as shown in the illustration.


c.

Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.


Hide 55550 22.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B433200C01
3.135,3.042 3.052,2.865 true 3.073,3.052 3.344,3.229 0.271,0.177 10 true *1 2.979,1.5 3.135,1.698 0.156,0.198 10 true A 0.479,1.271 0.635,1.469 0.156,0.198 10 true B
*1 Glove Compartment Door Stopper Sub-assembly


Disengage the claw to disconnect the glove compartment door stopper sub-assembly.


b.

Slightly bend stoppers (A) and (B) in the directions indicated by the arrows shown in the illustration and open the glove compartment door assembly until the stoppers are released.


c.

Open the glove compartment door assembly to approximately 64.2° from its closed position. Pull it horizontally in the direction indicated by the arrow shown in the illustration to disengage the 2 hinges and remove the glove compartment door assembly.

B437334C01
4.021,1.24 4.333,1.396 0.313,0.156 10 false *a
*a 64.2° - -
V113147

Remove in this Direction - -


NOTICE:

Pulling the glove compartment door assembly upward when removing it will cause the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.



Hide 55054 23.REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

a.
B433204

Disengage the claw to remove the glove compartment door stopper sub-assembly.


Hide 55406B 24.REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
B433205C01
0,0 0,0 false
V113146

Insert Moulding Remover Here
V113147

Remove in this Direction


Using a moulding remover, disengage the 2 clips as shown in the illustration.


b.
B433207C01
0,0 0,0 false
V113146

Insert Moulding Remover Here
V113147

Remove in this Direction


Using a moulding remover, disengage the 2 clips as shown in the illustration.


c.
B433209C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clip as shown in the illustration.


d.

Disconnect each connector.


e.

Disengage each clamp to remove the lower center instrument cluster finish panel sub-assembly.


Hide 58848B 25.REMOVE SHIFT LEVER HOLE COVER

a.
B433219

Disengage the clamp.


b.
B433221C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover, disengage the 5 clips as shown in the illustration.


c.

Disconnect each connector to remove the shift lever hole cover.


Hide 55433B 26.REMOVE NO. 2 LOWER INSTRUMENT PANEL FINISH PANEL

a.
B433226C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 4 clips as shown in the illustration.


b.
B433228C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 5 clips to remove the No. 2 lower instrument panel finish panel as shown in the illustration.


Hide 55650 27.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B433245C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the areas shown in the illustration.


b.
B433248C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover, disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.


Hide 55660 28.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B433293C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the areas shown in the illustration.


b.
B433296C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover, disengage the 4 clips to remove the No. 2 instrument panel register assembly as shown in the illustration.


Hide 81260 29.REMOVE GLOVE BOX LIGHT ASSEMBLY

Hide 82142A 30.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE

Hide 31.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

a.
B433243

Disengage the 2 claws and 4 clips to disconnect the lower instrument cover sub-assembly from the upper steering column cover.


b.
E337575C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws to disconnect the cooler (room temp. sensor) thermistor as shown in the illustration.


c.

Disconnect each connector.

B433256C01
5.563,0.417 5.885,0.635 0.323,0.219 12 true *A
*A w/ Digital Audio Broadcasting Antenna or Television Antenna - -



d.

Disengage each clamp.


e.

Remove the 2 clips.

B433257C01
5.094,5.031 5.406,5.188 0.313,0.156 10 true *a 2.76,1.219 3.073,1.375 0.313,0.156 10 true *c 3.604,3.969 3.917,4.125 0.313,0.156 10 true *b 5.917,3.406 6.229,3.563 0.313,0.156 10 true *d 0.771,1.271 1.083,1.427 0.313,0.156 10 true *e 5.729,0.625 6.042,0.781 0.313,0.156 10 true *e 4.896,0.938 5.208,1.094 0.313,0.156 10 true *c 3.24,4.417 3.552,4.573 0.313,0.156 10 true *c 2,4.667 2.313,4.823 0.313,0.156 10 true *b 5.281,3.344 5.594,3.5 0.313,0.156 10 true *b 6.531,2.938 6.844,3.094 0.313,0.156 10 true *b 5.729,4.938 6.042,5.094 0.313,0.156 10 true *a
*a Bolt <A> *b Bolt <B>
*c Screw <C> or <G> *d Screw <D>
*e Clip - -



f.

Remove the 2 bolts <A>, 4 bolts <B>, 3 screws <C> or <G> and screw <D> and remove the lower instrument panel sub-assembly.

NOTICE:
·

Do not damage the lower instrument panel sub-assembly.

·

Do not allow the wire harnesses to interfere with the surrounding parts.