Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SEAT POSITION SENSOR
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0230377 SEAT POSITION SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SEAT POSITION SENSOR  INSTALLATION  


PROCEDURE

Hide 89178A 1.INSTALL SEAT POSITION AIRBAG SENSOR

a.
B432361C01
0.615,0.76 0.958,0.385 0.958,0.385 1.302,0.385 true 2.052,0.281 2.281,0.281 2.281,0.281 2.563,0.594 true 1.906,0.188 2.219,0.344 0.313,0.156 10 false *a 1.333,0.313 1.646,0.469 0.313,0.156 10 false *b
*a Pin
*b Installation Hole


Insert the pin into the installation hole and temporarily install the seat position airbag sensor to the seat rail bracket with the "TORX" bolt as shown in the illustration.


b.
B434298C01
1.104,0.781 0.865,0.396 0.865,0.396 0.552,0.396 false 2.396,0.625 2.115,0.625 2.115,0.625 1.844,1.146 true 0.844,1.281 0.844,1.813 true 0.396,0.323 0.708,0.479 0.313,0.156 10 false *1 2.427,0.542 2.698,0.771 0.271,0.229 10 false *a 2.49,1.115 2.76,1.344 0.271,0.229 10 false *b 0.771,1.833 1.083,1.99 0.313,0.156 10 false *c
*1 Seat Position Airbag Sensor
*a Feeler Gauge
*b 1.3 mm (0.0512 in.)
*c Seat Track Bracket


Using a T30 "TORX" socket wrench and a 1.3 mm (0.0512 in.) feeler gauge, install the seat position airbag sensor with the "TORX" bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position airbag sensor with a new one.

·

When installing the seat position airbag sensor, make sure that the SRS wiring does not interfere with or is pinched between other parts.




c.

Make sure that the clearance between the seat position airbag sensor and seat track bracket is 1.3 mm (0.0512 in.).


d.

Check that there is no looseness in the installed parts of the seat position airbag sensor.


Hide 72277A 2.INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR

a.
B432359C01
0.906,0.708 1.406,0.708 true 0.875,1.5 1.219,1.5 1.219,1.5 1.375,1.698 true 1.875,0.323 2.208,0.323 2.208,0.323 2.396,0.531 true 1.448,0.635 1.76,0.792 0.313,0.156 10 false *c 0.698,1.417 0.906,1.615 0.208,0.198 10 true *a 1.719,0.24 2.031,0.396 0.313,0.156 10 false *b
*a Seat Rail Bracket
*b Pin
*c Installation Part
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the seat slide position sensor protector to the seat rail bracket and engage the pin to the installation part of the seat slide position sensor protector.


b.

Connect the connector and engage the clamp.