Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Manual Seat)
RM3210E _58 Vehicle Interior _047549 SEAT _0234654 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT SEAT ASSEMBLY

a.
B439660

Place the front seat assembly in the cabin.

NOTICE:

Be careful not to damage the vehicle body.



b.

Connect the front seat airbag assembly connector under the front seat assembly.

i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B345877C01
3.01,2.594 3.01,2.656 3.01,2.656 3.448,2.656 false 3,1.229 3,1.292 3,1.292 3.438,1.292 false 6.104,0.948 6.104,1.167 6.104,1.167 6.302,1.167 false 6.135,2.375 6.135,2.594 6.135,2.594 6.333,2.594 false 0.969,0.708 1.281,0.906 0.313,0.198 10 false *a 4.448,0.708 4.76,0.906 0.313,0.198 10 false *a 0.969,2.052 1.281,2.25 0.313,0.198 10 false *b 4.458,2.052 4.771,2.25 0.313,0.198 10 false *b 3.521,1.198 3.833,1.396 0.313,0.198 10 false *c 6.375,1.083 6.688,1.281 0.313,0.198 10 false *c 6.396,2.5 6.708,2.698 0.313,0.198 10 false *c 3.51,2.552 3.896,2.698 0.385,0.146 10 false *c
*a Correct *b Incorrect
*c Yellow CPA - -



ii.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.


·

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.





c.

Connect each connector and engage each clamp under the front seat assembly.


d.

Temporarily install the front seat assembly with the 4 bolts.


e.

Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.


f.
B439659N01
0.083,0.792 0.24,0.99 0.156,0.198 10 true 1 1.729,1.865 1.885,2.063 0.156,0.198 10 true 2

Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration.



g.

Operate the seat track adjusting handle and move the front seat assembly to the foremost position.


h.
B439658N01
2.198,1.635 2.354,1.833 0.156,0.198 10 true 1 1.083,1.615 1.24,1.813 0.156,0.198 10 true 2

Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration.



Hide 2.INSPECT SEAT SLIDE ADJUSTER LOCK

a.

While performing a sliding operation of the front seat assembly, check that the left and right adjusters move together smoothly and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the front seat assembly installation bolts and adjust the adjuster position.


Hide 72158 3.INSTALL INNER SEAT TRACK BRACKET COVER

a.

Operate the seat track adjusting handle and move the front seat assembly to the foremost position.


b.
B439781

Engage the 2 claws and guide to install the inner seat track bracket cover.


Hide 72138 4.INSTALL OUTER SEAT TRACK COVER

a.
B439780

Engage the 2 claws and guide to install the outer seat track cover.


Hide 72128A 5.INSTALL FRONT INNER SEAT TRACK BRACKET COVER

a.

Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.


b.
B439779

Engage the 2 claws to install the front inner seat track bracket cover.


Hide 72124 6.INSTALL FRONT OUTER SEAT TRACK BRACKET COVER

a.
B439778

Engage the 2 claws to install the front outer seat track bracket cover.


Hide 71910A 7.INSTALL FRONT SEAT HEADREST ASSEMBLY

a.

Install the front seat headrest assembly to the front seat assembly.


Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 9.CHECK SEAT HEATER (w/ Seat Heater System)

Hide 11. PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK (for Front Passenger Side)