Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY
RM3210E _59 Vehicle Exterior _047533 LIGHTING (EXT) _0231469 HEADLIGHT ASSEMBLY G

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  INSPECTION  


PROCEDURE

Hide 81131A 1.INSPECT HEADLIGHT UNIT RH

a.

Remove the headlight assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Remove the headlight unit RH from the headlight assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.

Inspect the headlight leveling motor circuit.

i.
E335897C23
0.792,0.948 1.094,1.167 0.302,0.219 0.552,2.677 0.844,2.885 0.292,0.208 1.938,2.792 2.281,1.917 true 2.052,2.792 2.583,2.115 true 1.917,2.99 2.208,3.208 true 0.938,1.802 1.25,2 0.313,0.198 10 false *b 1.417,0.333 1.729,0.531 0.313,0.198 10 false *a 0.906,0.979 1.219,1.177 0.313,0.198 10 false E 0.667,2.708 0.979,2.906 0.313,0.198 10 false B 2.115,1.719 2.781,1.938 0.667,0.219 10 false ACTBI 2.615,1.927 3.281,2.146 0.667,0.219 10 false ACTSI 2.24,3.208 2.906,3.427 0.667,0.219 10 false ACTGI
*a Component without harness connected
(to Headlight Leveling Motor RH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 - B-17 (ACTGI) Always Below 1 Ω
E-2 - B-8 (ACTSI) Always Below 1 Ω
E-3 - B-7 (ACTBI) Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH.



d.

Inspect the Lo / Hi beam headlight light source circuit.

i.
E337135C37
0.844,0.802 1.146,1 0.302,0.198 0.531,2.438 0.833,2.635 0.302,0.198 1.531,2.844 1.406,1.74 true 1.667,2.844 2.177,1.844 true 1.156,0.427 1.469,0.583 0.313,0.156 10 false *a 0.917,1.875 1.229,2.031 0.313,0.156 10 false *b 0.635,2.448 0.854,2.646 0.219,0.198 10 false B 0.958,0.823 1.177,1.021 0.219,0.198 10 false C 1.188,1.573 1.771,1.74 0.583,0.167 10 false LOLED2 2.021,1.667 2.604,1.833 0.583,0.167 10 false LOLED1
*a Component without harness connected
(to Headlight Unit RH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-5 - B-4 (LOLED2) Always Below 1 Ω
C-6 - B-5 (LOLED1) Always Below 1 Ω


If the result is not as specified, replace the headlight unit RH.



e.

Inspect the Lo / Hi beam shade circuit.

i.
E337135C38
0.844,0.802 1.146,1 0.302,0.198 0.531,2.438 0.833,2.635 0.302,0.198 1.177,2.844 0.823,2.219 true 2.26,2.844 2.583,2.26 true 1.156,0.427 1.469,0.583 0.313,0.156 10 false *a 0.917,1.875 1.229,2.031 0.313,0.156 10 false *b 0.646,2.469 0.865,2.667 0.219,0.198 10 false B 0.958,0.833 1.177,1.031 0.219,0.198 10 false C 2.531,2.094 2.844,2.26 0.313,0.167 10 false HI+ 0.729,2.052 1.042,2.219 0.313,0.167 10 false HI-
*a Component without harness connected
(to Headlight Unit RH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-10 - B-10 (HI+) Always Below 1 Ω
C-4 - B-1 (HI-) Always Below 1 Ω


If the result is not as specified, replace the headlight unit RH.



f.

Inspect the headlight fan circuit.

i.
E337135C39
0.844,0.802 1.146,1 0.302,0.198 0.531,2.438 0.833,2.635 0.302,0.198 1.802,2.865 2.24,2 true 1.531,3.094 1.396,3.26 true 1.688,3.094 1.854,3.25 true 1.156,0.427 1.469,0.583 0.313,0.156 10 false *a 0.917,1.875 1.229,2.031 0.313,0.156 10 false *b 0.646,2.458 0.865,2.656 0.219,0.198 10 false B 0.958,0.823 1.177,1.021 0.219,0.198 10 false C 2.125,1.854 2.573,2.01 0.448,0.156 10 false FANB 1.781,3.26 2.24,3.406 0.458,0.146 10 false FANP 1.167,3.26 1.615,3.417 0.448,0.156 10 false FANG
*a Component without harness connected
(to Headlight Unit RH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-12 - B-6 (FANB) Always Below 1 Ω
C-11 - B-15 (FANP) Always Below 1 Ω
C-4 - B-14 (FANG) Always Below 1 Ω


If the result is not as specified, replace the headlight unit RH.



g.

Inspect the clearance light circuit.

i.
E335891C23
0.635,1.073 0.958,1.323 0.323,0.25 0.427,2.979 0.771,3.198 0.344,0.219 2.188,3.146 2.542,2.333 true 0.958,2.323 1.354,3.01 true 0.615,0.208 0.927,0.365 0.313,0.156 10 false *a 0.302,2.24 0.615,2.396 0.313,0.156 10 false *b 0.76,1.125 1.073,1.281 0.313,0.156 10 false D 0.563,3.021 0.875,3.177 0.313,0.156 10 false B 2.427,2.146 2.948,2.333 0.521,0.188 10 false CLL+ 0.823,2.146 1.344,2.333 0.521,0.188 10 false CLL-
*a Component without harness connected
(to Headlight Lens RH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-2 - B-19 (CLL+) Always Below 1 Ω
D-1 - B-2 (CLL-) Always Below 1 Ω


If the result is not as specified, replace the headlight unit RH.



Hide 81171A 2.INSPECT HEADLIGHT UNIT LH

a.

Remove the headlight assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Remove the headlight unit LH from the headlight assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.

Inspect the headlight leveling motor circuit.

i.
E335897C23
0.792,0.948 1.094,1.167 0.302,0.219 0.552,2.677 0.844,2.885 0.292,0.208 1.938,2.792 2.281,1.917 true 2.052,2.792 2.583,2.115 true 1.917,2.99 2.208,3.208 true 0.938,1.802 1.25,2 0.313,0.198 10 false *b 1.417,0.333 1.729,0.531 0.313,0.198 10 false *a 0.906,0.979 1.219,1.177 0.313,0.198 10 false E 0.667,2.708 0.979,2.906 0.313,0.198 10 false B 2.115,1.719 2.781,1.938 0.667,0.219 10 false ACTBI 2.615,1.927 3.281,2.146 0.667,0.219 10 false ACTSI 2.24,3.208 2.906,3.427 0.667,0.219 10 false ACTGI
*a Component without harness connected
(to Headlight Leveling Motor LH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 - B-17 (ACTGI) Always Below 1 Ω
E-2 - B-8 (ACTSI) Always Below 1 Ω
E-3 - B-7 (ACTBI) Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH.



d.

Inspect the Lo / Hi beam headlight light source circuit.

i.
E337135C37
0.844,0.802 1.146,1 0.302,0.198 0.531,2.438 0.833,2.635 0.302,0.198 1.531,2.844 1.406,1.74 true 1.667,2.844 2.177,1.844 true 1.156,0.427 1.469,0.583 0.313,0.156 10 false *a 0.917,1.875 1.229,2.031 0.313,0.156 10 false *b 0.635,2.448 0.854,2.646 0.219,0.198 10 false B 0.958,0.823 1.177,1.021 0.219,0.198 10 false C 1.188,1.573 1.771,1.74 0.583,0.167 10 false LOLED2 2.021,1.667 2.604,1.833 0.583,0.167 10 false LOLED1
*a Component without harness connected
(to Headlight Unit LH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-5 - B-4 (LOLED2) Always Below 1 Ω
C-6 - B-5 (LOLED1) Always Below 1 Ω


If the result is not as specified, replace the headlight unit LH.



e.

Inspect the Lo / Hi beam shade circuit.

i.
E337135C38
0.844,0.802 1.146,1 0.302,0.198 0.531,2.438 0.833,2.635 0.302,0.198 1.177,2.844 0.823,2.219 true 2.26,2.844 2.583,2.26 true 1.156,0.427 1.469,0.583 0.313,0.156 10 false *a 0.917,1.875 1.229,2.031 0.313,0.156 10 false *b 0.646,2.469 0.865,2.667 0.219,0.198 10 false B 0.958,0.833 1.177,1.031 0.219,0.198 10 false C 2.531,2.094 2.844,2.26 0.313,0.167 10 false HI+ 0.729,2.052 1.042,2.219 0.313,0.167 10 false HI-
*a Component without harness connected
(to Headlight Unit LH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-10 - B-10 (HI+) Always Below 1 Ω
C-4 - B-1 (HI-) Always Below 1 Ω


If the result is not as specified, replace the headlight unit LH.



f.

Inspect the headlight fan circuit.

i.
E337135C39
0.844,0.802 1.146,1 0.302,0.198 0.531,2.438 0.833,2.635 0.302,0.198 1.802,2.865 2.24,2 true 1.531,3.094 1.396,3.26 true 1.688,3.094 1.854,3.25 true 1.156,0.427 1.469,0.583 0.313,0.156 10 false *a 0.917,1.875 1.229,2.031 0.313,0.156 10 false *b 0.646,2.458 0.865,2.656 0.219,0.198 10 false B 0.958,0.823 1.177,1.021 0.219,0.198 10 false C 2.125,1.854 2.573,2.01 0.448,0.156 10 false FANB 1.781,3.26 2.24,3.406 0.458,0.146 10 false FANP 1.167,3.26 1.615,3.417 0.448,0.156 10 false FANG
*a Component without harness connected
(to Headlight Unit LH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-12 - B-6 (FANB) Always Below 1 Ω
C-11 - B-15 (FANP) Always Below 1 Ω
C-4 - B-14 (FANG) Always Below 1 Ω


If the result is not as specified, replace the headlight unit LH.



g.

Inspect the clearance light circuit.

i.
E335891C23
0.635,1.073 0.958,1.323 0.323,0.25 0.427,2.979 0.771,3.198 0.344,0.219 2.188,3.146 2.542,2.333 true 0.958,2.323 1.354,3.01 true 0.615,0.208 0.927,0.365 0.313,0.156 10 false *a 0.302,2.24 0.615,2.396 0.313,0.156 10 false *b 0.76,1.125 1.073,1.281 0.313,0.156 10 false D 0.563,3.021 0.875,3.177 0.313,0.156 10 false B 2.427,2.146 2.948,2.333 0.521,0.188 10 false CLL+ 0.823,2.146 1.344,2.333 0.521,0.188 10 false CLL-
*a Component without harness connected
(to Headlight Lens LH)
*b Component without harness connected
(to No. 1 Headlight ECU Sub-assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-2 - B-19 (CLL+) Always Below 1 Ω
D-1 - B-2 (CLL-) Always Below 1 Ω


If the result is not as specified, replace the headlight unit LH.