1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT
89510D
2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY
Do not drop the brake pedal stroke sensor assembly.
If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.
When installing a new brake pedal stroke sensor assembly:
Do not break the brake pedal stroke sensor assembly lever set pin before installing the brake pedal stroke sensor assembly with the 2 nuts.
| *a | Brake Pedal Stroke Sensor Assembly Lever |
| *b | Brake Pedal Groove |
| *c | Brake Pedal Stroke Sensor Assembly Lever Set Pin |
Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.
Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.
Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.
Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.
Connect the connector.
Firmly depress the brake pedal to break the brake pedal stroke sensor assembly lever set pin.
Remove the broken lever set pin.
When reusing the brake pedal stroke sensor assembly:
| *a | Brake Pedal Stroke Sensor Assembly Lever |
| *b | Brake Pedal Groove |
Install the brake pedal stroke sensor assembly to the brake pedal support assembly and temporarily tighten the 2 nuts.
Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.
Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.
Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.
Connect the connector.
55480D
3.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Use the same procedure as for the LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION
53601
4.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Use the same procedure as for the LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION
55470
5.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY
Use the same procedure as for the LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION
6.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
89510D
7.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY
When the brake pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.
Connect the GTS to the DLC3 with the power switch off.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor.
| Tester Display |
|---|
| Stroke Sensor |
Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.
0.8 to 1.2 V
Tighten the 2 nuts.
Do not depress the brake pedal after turning the power switch on (IG).
Turn the GTS off and turn the power switch off.
Disconnect the GTS from the DLC3.
55435A
8.INSTALL INSTRUMENT PANEL FINISH PANEL END RH
Use the same procedure as for the LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION
55606
9.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
62111C
10.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
67913
11.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
12. PERFORM INITIALIZATION AND CALIBRATION
Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
13.CHECK AND CLEAR DTC