Wear protective gloves. Sharp areas on the parts may injure your hands.
Power seat is available only on the driver side.
Use the same procedure for RHD and LHD vehicles.
The following procedure is for LHD vehicles.
71874C
1.INSTALL FRONT SEAT LOWER NO. 1 CUSHION SHIELD LH
|
Install in this direction |
Engage the guide as shown in the illustration.
Engage the claw to install the front seat lower No. 1 cushion shield LH.
7181B
2.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER LH
|
Install in this direction |
Engage the guide as shown in the illustration.
Engage the 2 claws to install the front seat cushion wire harness holder LH.
Install the 2 screws.
71052A
3.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH
Engage the 6 hooks to install the front seat cushion spring sub-assembly LH to the front seat adjuster assembly LH.
82192
4.INSTALL FRONT SEAT WIRE LH
Connect each connector and engage each clamp to install the front seat wire LH.
71874A
5.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
| *a | Hook |
| *b | Guide |
Engage the claw and guide.
Engage the hook to install the front seat lower cushion shield LH.
71873A
6.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
| *a | Hook |
| *b | Guide |
Engage the claw and guide.
Engage the hook to install the front seat lower cushion shield RH.
71875G
7.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER LH
Engage the 4 claws to install the LH seat reclining adjuster inside cover LH.
Engage the claw.
71876G
8.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH
Engage the 4 claws to install the LH seat reclining adjuster inside cover RH.
87510L
9.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH
71072S
10.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Engage the 13 claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.
11.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Engage the 10 hooks to install the separate type front seat cushion cover with pad.
Engage the clamp to install the front seat cushion heater assembly LH wire harness.
Connect the connector.
8219B
12.INSTALL FRONT SEAT NO. 2 WIRE LH
Connect each connector and engage each clamp to install the front seat No. 2 wire LH.
71759B
13.INSTALL FRONT SEATBACK HOOK
Install the 2 front seatback hooks to the front seatback frame sub-assembly LH.
71587
14.INSTALL FRONT SEATBACK EDGE PROTECTOR
Install the 2 front seatback edge protectors to the lumbar support adjuster assembly LH.
72760D
15.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH
73920A
16.INSTALL FRONT SEAT AIRBAG ASSEMBLY LH
87510N
17.INSTALL FRONT SEATBACK HEATER ASSEMBLY LH
71074S
18.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Engage the 17 claws to install the separate type front seatback cover to the separate type front seatback pad.
19.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad.
71931
20.INSTALL FRONT SEAT HEADREST SUPPORT
Engage the 4 claws to install the 2 front seat headrest supports.
Close the 2 fasteners.
Engage the clamp.
Engage the 3 hooks.
21.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Engage the 4 guides.
Install the separate type front seatback assembly to the separate type front seat cushion assembly with the 4 bolts.
Engage the claw and 4 clamps to install the front seat airbag assembly LH wire harness.
Engage the claw first.
Engage the clamp.
Connect the front seatback heater assembly LH connector.
Engage the clamp.
Connect the connector.
Engage the 2 hooks.
84922C
22.INSTALL FRONT POWER SEAT SWITCH LH
71825
23.INSTALL FRONT SEAT SIDE NO. 1 BRACKET LH
Install the front seat side No. 1 bracket LH to the front seat cushion shield LH with the 2 screws.
84921K
24.INSTALL RECLINING POWER SEAT SWITCH KNOB
Engage the 4 claws to install the reclining power seat switch knob.
84921D
25.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Engage the 4 claws to install the slide and vertical power seat switch knob.
71862
26.INSTALL FRONT SEAT INNER CUSHION SHIELD LH
|
Install in this direction |
Engage the 2 claws and 2 guides as shown in the illustration.
Engage the 2 claws to install the front seat inner cushion shield LH.
71812D
27.INSTALL FRONT SEAT CUSHION SHIELD LH
Connect the front power seat switch LH connector.
|
Install in this direction (1) |
|
Install in this direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the 2 claws and 2 guides (B) as shown in the illustration.
Engage the 2 claws to install the front seat cushion shield LH.
71868A
28.INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH
Engage the 3 guides.
Engage the 2 claws as shown in the illustration.
Engage the guide as shown in the illustration.
Install the front seat inner No. 1 cushion shield LH with the clip.
71074S
29.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.
73240
30.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH