Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY
RM3210E _58 Vehicle Interior _047538 SEAT BELT _0234841 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat outer belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

CAUTION:
·
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67914 3.REMOVE FRONT DOOR SCUFF PLATE

Hide 62312B 4.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the front door opening trim weatherstrip.


Hide 67918A 5.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 6.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the rear door opening trim weatherstrip.


Hide 73233 7.REMOVE LAP BELT OUTER ANCHOR COVER

a.
B434982

Disengage the 3 claws to remove the lap belt outer anchor cover.


Hide 73220 8.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.
B434983

Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.


Hide 62414A 9.REMOVE LOWER CENTER PILLAR GARNISH

Hide 62420A 10.REMOVE CENTER PILLAR GARNISH ASSEMBLY

Hide 73220 11.REMOVE FRONT SEAT OUTER BELT ASSEMBLY

a.
B434984

Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.


b.
B434985C01
0.656,0.781 0.906,0.635 true 1.135,0.719 1.313,0.688 true 1.365,0.594 1.646,0.865 0.281,0.271 10 false *a 0.5,0.708 0.75,0.979 0.25,0.271 10 false *b 1.052,0.188 1.302,0.427 0.25,0.24 10 false *c
*a Protective Tape
*b Locking Button
*c Release


Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

HINT:

Tape the screwdriver tip before use.



c.
B434986

Remove the 2 bolts.


d.

Disengage the 2 guides to remove the front seat outer belt assembly.


Hide 73200A 12.REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B434987

Remove the 2 bolts.


b.

Disengage the guide to remove the front shoulder belt anchor adjuster assembly.