Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P003612  HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery  P003614  HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open  P014118  O2 Sensor Heater Circuit Bank 1 Sensor 2 Circuit Current Below Threshold  P102A9E  O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On  


DESCRIPTION

Refer to DTC P013611.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P013611

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the power switch is turned off.

·

The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.

A296575E03
0.115,0.115 2.885,0.323 2.771,0.208 10 false Reference (System Diagram of Sensor 2): 0.104,1.083 0.979,1.635 0.875,0.552 10 false from Auxiliary Battery 1.115,1.26 2,1.5 0.885,0.24 10 false EFI-MAIN 2.115,2.375 3,2.615 0.885,0.24 10 false EFI-MAIN 2.927,1.271 3.604,1.49 0.677,0.219 10 false EFI NO. 3 3.479,2.25 4.948,2.479 1.469,0.229 10 false Heated Oxygen Sensor 3.844,1.875 4.396,2.156 0.552,0.281 10 false Sensor 3.875,1.271 4.427,1.552 0.552,0.281 10 false Heater 3.469,1.01 3.792,1.24 0.323,0.229 10 false +B 4.51,1.563 4.948,1.781 0.438,0.219 10 false OX1B 4.521,1 4.958,1.219 0.438,0.219 10 false HT1B 3.458,1.563 3.698,1.813 0.24,0.25 10 false E2 5.104,1.552 5.542,1.771 0.438,0.219 10 false OX1B 5.115,0.99 5.552,1.208 0.438,0.219 10 false HT1B 5.104,2.594 5.542,2.813 0.438,0.219 10 false EX1B 5.833,3.49 6.271,3.708 0.438,0.219 10 false ECM 5.115,2.979 5.552,3.198 0.438,0.219 10 false MREL



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P003612 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery The heated oxygen sensor heater current is the specified value or higher while the heater is operating (1 trip detection logic).
·

Short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

ECM


Comes on DTC stored SAE Code: P0038
P003614 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open The heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open or short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

ECM


Comes on DTC stored SAE Code: P0037
P014118 O2 Sensor Heater Circuit Bank 1 Sensor 2 Circuit Current Below Threshold The heated oxygen sensor impedance value exceeds the threshold (2 trip detection logic).
·

Open or short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

ECM


Comes on DTC stored SAE Code: P0141
P102A9E O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On The heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

ECM


Comes on DTC stored SAE Code: P102D

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check and Heater Performance (Stuck ON) (P003612, P003614 and P102A9E):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction of the sensor heater and stores a DTC.



Heated Oxygen Sensor Heater Performance (Heater Impedance) (P014118):

After the accumulated heater on time exceeds 100 or 250 seconds, the ECM calculates the heater resistance using auxiliary battery voltage and the current applied to the heater. If the resistance is above the threshold value, the ECM determines that there is a malfunction in the heated oxygen sensor heater and stores DTC P014118.



MONITOR STRATEGY

Required Sensors/Components Heated oxygen sensor (sensor 2) heater
Frequency of Operation Continuous: P0037, P0038, P102D
Once per driving cycle: P0141

TYPICAL ENABLING CONDITIONS

P003612
Time after heater on 10 seconds or more

P003614
Time after heater on 10 seconds or more

P014118
Accumulated heater on time 100 seconds or more

P102A9E
Time after heater on 10 seconds or more

CONFIRMATION DRIVING PATTERN

A198819E77
0.75,0.969 1.396,1.167 0.646,0.198 10 2500 rpm 0.948,1.74 1.354,1.896 0.406,0.156 10 Idling 0.427,2.01 1.302,2.333 0.875,0.323 10 Power Switch on (IG) 1.927,2.167 2.417,2.49 0.49,0.323 10 [A] 2.76,1.625 3.635,2 0.875,0.375 10 [B] 4.021,0.865 4.521,1.385 0.5,0.521 10 [C] 5.385,1.604 6.083,2.188 0.698,0.583 10 [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 5 minutes or more 3.854,2.615 4.427,2.781 0.573,0.167 10 1 minute 5.979,3.031 6.406,3.458 0.427,0.427 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and idle it for 5 minutes or more [B].

10.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 2500 rpm for 1 minute [C].

HINT:

During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, perform steps [C] and [D] after charge control has completed.


11.

Idle the engine for 5 minutes or more [D].

12.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P003612, P003614, P014118 or P102A9E.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform steps [B] through [E] again.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

The operation of the heated oxygen sensor heater can be checked by referring to the Data List items "O2 Sensor Heater B1S2" and "O2 Sensor Heater Current Value B1S2".

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DATA LIST / ACTIVE TEST

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

When the value of the Data List item O2 Sensor Heater Current Value B1S2 is not 0 A, the heater is on.

·

Change the fuel injection volume using the Active Test "Control the Injection Volume for A/F Sensor" and monitor the heated oxygen sensor output voltage (Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P013611). If the heated oxygen sensor output voltage does not change (almost no reaction) while performing the Active Test, the heated oxygen sensor may be malfunctioning.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
A376499C01
0.396,0.875 0.802,1.167 0.406,0.292 1.896,0.969 2.302,0.729 true 0.156,0.167 0.469,0.323 0.313,0.156 10 false *a 2.375,0.635 2.688,0.792 0.313,0.156 10 false +B 0.521,0.958 0.833,1.115 0.313,0.156 10 false C9
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


a.

Disconnect the heated oxygen sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C9-2 (+B) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - HEATED OXYGEN SENSOR)

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C9-1 (HT1B) - C31-56 (HT1B) Always Below 1 Ω
C9-1 (HT1B) or C31-56 (HT1B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003612, P003614, P014118 OR P102A9E)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003612, P003614, P014118 OR P102A9E)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P003612, P003614, P014118 or P102A9E is output B




A

B