Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P040314  Exhaust Gas Recirculation "A" Control Circuit 1 Open  P140000  Exhaust Gas Recirculation "A" Control Circuit 2 Open  P140596  Exhaust Gas Recirculation "A" Control Circuit 3 Open  P141004  Exhaust Gas Recirculation "A" Control Circuit 4 Open  


DESCRIPTION

Refer to DTC P04019C.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P04019C

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P040314 Exhaust Gas Recirculation "A" Control Circuit 1 Open Open or short in EGR1 circuit for 1 second or more (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code: P0403
P140000 Exhaust Gas Recirculation "A" Control Circuit 2 Open Open or short in EGR2 circuit for 1 second or more (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code: P0403
P140596 Exhaust Gas Recirculation "A" Control Circuit 3 Open Open or short in EGR3 circuit for 1 second or more (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code: P0403
P141004 Exhaust Gas Recirculation "A" Control Circuit 4 Open Open or short in EGR4 circuit for 1 second or more (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code: P0403

MONITOR DESCRIPTION

These DTCs are stored if an open or short in the EGR valve assembly circuit is detected.

Example:

·

If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, but the step motor is still operating, the ECM determines that there is a short in the EGR valve assembly circuit, illuminate the MIL and stores a DTC.

·

If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, and the step motor is not operating, the ECM determines that there is an open in the EGR valve assembly circuit, illuminate the MIL and stores a DTC.


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A215251E28
2.333,2.896 2.917,3.302 0.583,0.406 10 false Warming up 3.146,2.906 4.479,3.104 1.333,0.198 10 false 10 minutes or more 2.021,2.083 2.344,2.323 0.323,0.24 10 false [A] 2.531,1.781 2.792,2.063 0.26,0.281 10 false [B] 3.781,0.688 4.156,1.115 0.375,0.427 10 false [C] 4.438,3.292 4.75,3.604 0.313,0.313 10 false [D] 0.719,0.823 1.75,1.406 1.031,0.583 10 false 20 km/h or more [Engine running] 1.438,1.906 1.813,2.083 0.375,0.177 10 false Idling 0.49,2.25 1.885,2.51 1.396,0.26 10 false Power Switch on (IG)

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up [B].

10.

With the engine running, drive the vehicle at 20 km/h (12 mph) or more for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P040314, P140000, P140596 or P141004.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A377137E01
0.583,3.979 3.188,4.177 2.604,0.198 10 false Auxiliary Battery 0.406,3.198 3.01,3.396 2.604,0.198 10 false BATT-MAIN 0.406,2.531 3.01,2.729 2.604,0.198 10 false EFI-MAIN 1.781,1.604 4.385,1.802 2.604,0.198 10 false EFI-MAIN 1.208,1.948 3.813,2.146 2.604,0.198 10 false 1B 1.469,1.948 4.073,2.146 2.604,0.198 10 false No. 1 Integration Relay 1.365,1.115 1.604,1.396 0.24,0.281 10 false 5 1.365,0.583 1.604,0.865 0.24,0.281 10 false 3 2.708,0.583 2.948,0.865 0.24,0.281 10 false 4 2.708,1.115 2.948,1.396 0.24,0.281 10 false 6 3.396,0.844 6,1.042 2.604,0.198 10 false EFI NO. 3 1.531,5.208 4.135,5.406 2.604,0.198 10 false C10 1.875,5.208 4.479,5.406 2.604,0.198 10 false EGR Valve Assembly 3.354,2.813 3.594,3.094 0.24,0.281 10 false 4 3.344,3.198 3.583,3.479 0.24,0.281 10 false 3 3.344,3.583 3.583,3.865 0.24,0.281 10 false 6 3.333,3.979 3.573,4.26 0.24,0.281 10 false 1 3.344,4.365 3.583,4.646 0.24,0.281 10 false 2 3.333,4.74 3.573,5.021 0.24,0.281 10 false 5 2.854,3.198 3.542,3.49 0.688,0.292 10 false EGR2 2.854,3.583 3.542,3.875 0.688,0.292 10 false EGR3 2.865,3.99 3.552,4.281 0.688,0.292 10 false EGR4 2.969,4.365 3.656,4.656 0.688,0.292 10 false +B1 2.969,4.74 3.656,5.031 0.688,0.292 10 false +B2 5.271,1.052 5.646,1.333 0.375,0.281 10 false 46 5.229,1.219 5.604,1.5 0.375,0.281 10 false A40 5.573,1.125 6.052,1.438 0.479,0.313 10 false MREL 5.219,2.729 5.594,3.01 0.375,0.281 10 false 140 5.219,3.115 5.594,3.396 0.375,0.281 10 false 106 5.219,3.51 5.594,3.792 0.375,0.281 10 false 107 5.198,3.906 5.573,4.188 0.375,0.281 10 false 105 5.219,2.917 5.594,3.198 0.375,0.281 10 false C31 5.219,3.302 5.594,3.583 0.375,0.281 10 false C31 5.208,3.688 5.583,3.969 0.375,0.281 10 false C31 5.219,4.083 5.594,4.365 0.375,0.281 10 false C31 2.865,2.802 3.552,3.094 0.688,0.292 10 false EGR1 5.594,2.813 6.281,3.104 0.688,0.292 10 false EGR1 5.583,3.188 6.271,3.479 0.688,0.292 10 false EGR2 5.583,3.583 6.271,3.875 0.688,0.292 10 false EGR3 5.594,3.969 6.281,4.26 0.688,0.292 10 false EGR4 6.052,4.885 6.74,5.177 0.688,0.292 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



f.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Intake Manifold Absolute Pressure and Engine Independent.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
Engine Independent
50004 372 25 385,428

g.

Confirm that the value of Data List item Engine Independent is "Operate" then check the value of Intake Manifold Absolute Pressure while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

Intake Manifold Absolute Pressure value change in response to EGR step position when Engine Independent is Operate in Data List.


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Intake Manifold Absolute Pressure
(Data List)
(EGR valve is fully closed) Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:
·

If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).

·

While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.




Result:
Proceed to
OK
NG



OK

NG

2.INSPECT EGR VALVE ASSEMBLY
2.INSPECT EGR VALVE ASSEMBLY
a.

Inspect the EGR valve assembly.

Click hereEngine / Hybrid System>2ZR-FXE EMISSION CONTROL>EGR VALVE>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)
A376490C02
0.354,1.031 0.75,1.271 0.396,0.24 1.76,0.938 2.323,0.594 true 2.469,1.885 1.698,1.396 true 0.208,0.146 0.521,0.344 0.313,0.198 10 false *a 0.438,1.083 0.896,1.281 0.458,0.198 10 false C10 2.396,0.542 2.854,0.74 0.458,0.198 10 false +B1 2.552,1.854 3.01,2.052 0.458,0.198 10 false +B2
*a Front view of wire harness connector
(to EGR Valve Assembly)


a.

Disconnect the EGR valve assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C10-2 (+B1) - Body ground Power switch on (IG) 11 to 14 V
C10-5 (+B2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - EGR VALVE ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)
a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C10-4 (EGR1) - C31-140 (EGR1) Always Below 1 Ω
C10-3 (EGR2) - C31-106 (EGR2) Always Below 1 Ω
C10-6 (EGR3) - C31-107 (EGR3) Always Below 1 Ω
C10-1 (EGR4) - C31-105 (EGR4) Always Below 1 Ω
C10-4 (EGR1) or C31-140 (EGR1) - Body ground and other terminals Always 10 kΩ or higher
C10-3 (EGR2) or C31-106 (EGR2) - Body ground and other terminals Always 10 kΩ or higher
C10-6 (EGR3) or C31-107 (EGR3) - Body ground and other terminals Always 10 kΩ or higher
C10-1 (EGR4) or C31-105 (EGR4) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR