Home › Engine / Hybrid System › 2ZR-FXE EMISSION CONTROL › EGR VALVE
RM3210E _51 Engine / Hybrid System _047497 2ZR-FXE EMISSION CONTROL _0236605 EGR VALVE A

2ZR-FXE EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control System) (Click here)
Intelligent clearance sonar system*1
Simple advanced parking guidance system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Replacement of EGR valve assembly Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 51444C 3.REMOVE REAR MOTOR UNDER COVER LH

Hide 4.DRAIN ENGINE COOLANT (for Engine)

Hide 7.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 8.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

Hide 55738D 9.REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

Hide 55735A 10.REMOVE WATER GUARD PLATE LH

Hide 55736D 11.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55701J 12.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 12601B 13.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 74404A 14.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 82121 15.DISCONNECT ENGINE WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.
A377688C01
1.646,0.875 2.094,0.875 true 1.333,1.115 1.521,1.302 0.188,0.188 10 true *a 2.115,0.781 2.323,0.979 0.208,0.198 10 true *b
*a Push
*b Lock


Raise the lever while pushing the lock on the lever, and disconnect the ECM connector.

NOTICE:

After disconnecting the ECM connector, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connector.



b.
A376302

Remove the No. 1 relay block cover.


c.
A376303

Disconnect the 3 No. 1 engine room relay block and No. 1 junction block assembly connectors.


d.

Disengage the 2 claws.


e.
A376292

Move the 2 lock levers as shown in the illustration and disconnect the 2 inverter with converter assembly connectors.

NOTICE:
·

Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

·

Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

·

Do not allow any foreign matter or water to enter the inverter with converter assembly.

·

Insulate the disconnected terminals with insulating tape.

·

Do not touch the waterproof seal or terminals of the connector.




f.
A377693

Remove the 3 bolts.


g.

Disengage the 4 clamps and disconnect the engine wire.


Hide 18.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

Hide 82311A 20.DISCONNECT AIR CONDITIONING WIRE

Hide G9200 21.SEPARATE INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Wear insulated gloves.


a.

Remove the 5 bolts and 2 nuts and separate the inverter with converter assembly.

A378886C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


NOTICE:
·

To prevent damage due to static electricity, do not touch the terminals of the inverter with converter assembly connector.

·

Make sure to seal the inverter with converter assembly with the connector cover assembly or tape (non-residue type) etc., to prevent entry of foreign matter and water.




b.
A377698C01
2.771,0.698 2.646,0.708 2.646,0.708 2.438,0.365 true 2.781,0.625 3.01,0.802 0.229,0.177 10 true *a
*a Rope


Using a rope or equivalent, secure the inverter with converter assembly with the hood hinge.

NOTICE:
·

Be careful not to damage the surrounding components when securing the inverter with converter assembly.

·

To prevent damage to the inverter with converter assembly, do not hold the coolant pipe, bracket or connector when securing the inverter with converter assembly.

·

To prevent damage due to static electricity, do not touch the terminals of the inverter with converter assembly connector.

·

Make sure to seal the inverter with converter assembly with the connector cover assembly or tape (non-residue type) etc., to prevent entry of foreign matter and water.




Hide 25620 23.REMOVE EGR VALVE ASSEMBLY

a.
A377699

Disconnect the EGR valve assembly connector.


b.
A377700

Slide the clip and disconnect the No. 6 water by-pass hose from the EGR valve assembly.


c.
A377758

Slide the clip and disconnect the water by-pass hose assembly from the EGR valve assembly.


d.
A377702C01
0,0 0,0 false

Remove the 3 nuts.


e.
A377703

Using an E8 "TORX" socket wrench, remove the stud bolt from the camshaft housing sub-assembly.

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.



f.

Remove the EGR valve assembly from the EGR pipe with cooler sub-assembly.


g.
A377704

Remove the EGR valve gasket from the EGR valve assembly.