Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P045011  Evaporative Emission System Pressure Sensor/Switch Circuit Short to Ground  P045015  Evaporative Emission System Pressure Sensor/Switch Circuit Short to Battery or Open  P04502F  Evaporative Emission System Pressure Sensor/Switch Signal Erratic  


DTC SUMMARY

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P045011 Evaporative Emission System Pressure Sensor/Switch Circuit Short to Ground EVAP pressure is less than 42.11009 kPa(abs) [6.10596 psi(abs)] for 0.5 seconds or more.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

ECM


Comes on DTC stored SAE Code: P0452
P045015 Evaporative Emission System Pressure Sensor/Switch Circuit Short to Battery or Open EVAP pressure is higher than 123.76147 kPa(abs) [17.94541 psi(abs)] for 0.5 seconds or more.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

ECM


Comes on DTC stored SAE Code: P0453
P04502F Evaporative Emission System Pressure Sensor/Switch Signal Erratic Canister pressure sensor output voltage fluctuates frequently for a certain amount of time.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


Comes on DTC stored SAE Code: P0451

DTC No. Monitoring Item Detection Timing Detection Logic SAE Code
P045011 Canister pressure sensor low input
·

Power switch on (IG)

·

EVAP monitoring (power switch off)


1 trip P0452
P045015 Canister pressure sensor high input
·

Power switch on (IG)

·

EVAP monitoring (power switch off)


1 trip P0453
P04502F Canister pressure sensor abnormal voltage fluctuation (Noise monitor)
·

EVAP monitoring (power switch off)

·

Engine running


2 trip P0451

HINT:

The canister pressure sensor is built into the canister pump module.


DESCRIPTION

MONITOR DESCRIPTION

A304708E04
4.583,3.302 5.083,3 true 4.583,1.417 5.083,1.115 true 0.167,0.167 2.667,0.333 2.5,0.167 10 false Canister Pressure Sensor Specification: 1.25,1 2.25,1.167 1,0.167 10 false Output Voltage 1.708,1.427 2.292,1.594 0.583,0.167 10 false 4.900 V 1.708,1.917 2.292,2.083 0.583,0.167 10 false 4.423 V 1.708,2.604 2.292,2.771 0.583,0.167 10 false 1.425 V 1.708,3.021 2.292,3.188 0.583,0.167 10 false 0.450 V 2.802,3.469 3.385,3.635 0.583,0.167 10 false 60 [8.7] 3.375,3.469 4.177,3.677 0.802,0.208 10 false 115 [17] 4.208,3.479 5.438,3.865 1.229,0.385 10 false kPa(abs) [psi(abs)] 5.542,3.333 6.208,3.5 0.667,0.167 10 false Pressure 5.115,2.917 6.198,3.083 1.083,0.167 10 false Malfunction Area 5.115,1.031 6.198,1.198 1.083,0.167 10 false Malfunction Area 3.833,2.333 4.75,2.5 0.917,0.167 10 false Usable Range 1,4 1.417,4.167 0.417,0.167 10 false HINT: 1,4.333 5.208,4.594 4.208,0.26 10 false Standard atmospheric pressure is 101.3 kPa(abs) [14.7 psi(abs)]

1.

DTC P045011: Canister pressure sensor voltage low

If the canister pressure sensor output voltage (pressure) is less than 0.45 V: 42.11009 kPa(abs) [6.10596 psi(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. If any deterioration has occurred, the ECM will illuminate the MIL and store this DTC (1 trip detection logic).

2.

DTC P045015: Canister pressure sensor voltage high

If the canister pressure sensor output voltage (pressure) is higher than 4.9 V: 123.76147 kPa(abs) [17.94541 psi(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. If any deterioration has occurred, the ECM will illuminate the MIL and store this DTC (1 trip detection logic).

3.

DTC P04502F: Canister pressure sensor abnormal voltage fluctuation (Noise monitor)

If the canister pressure sensor output voltage fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as the canister pressure sensor voltage fluctuating, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores this DTC (2 trip detection logic).


MONITOR STRATEGY

Required Sensors/Components Canister pump module
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 9 steps performed automatically by the GTS. It takes a maximum of approximately 40 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not start the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor will from and any check result will be inaccurate. When performing the Evaporative System Check, keep the fuel temperature less than 35°C (95°F).



1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature.

5.

Check that the intake air temperature is between 4.4 and 50°C (39.9 and 122°F).

6.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

7.

Turn the power switch off and wait for at least 30 seconds.

8.

Turn the power switch on (IG).

9.

Turn the GTS on.

10.

Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Automatic Mode.

11.

After the Evaporative System Check is completed, check for All Readiness by entering the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P045011, P045015 or P04502F.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

A377770E01
1.115,1.865 4.938,2.063 3.823,0.198 10 false Fuel Tank Pressure Sensor 1.125,1.688 4.948,1.885 3.823,0.198 10 false M62 2.094,0.719 2.583,0.927 0.49,0.208 10 false VC 1.948,1.115 2.438,1.323 0.49,0.208 10 false PTNK 2.125,1.479 2.615,1.688 0.49,0.208 10 false E2 2.417,0.594 2.906,0.802 0.49,0.208 10 false 3 2.427,0.99 2.917,1.198 0.49,0.208 10 false 2 2.427,1.365 2.917,1.573 0.49,0.208 10 false 1 5.177,0.729 5.667,0.938 0.49,0.208 10 false C31 5.177,1.115 5.667,1.323 0.49,0.208 10 false C31 5.177,1.5 5.667,1.708 0.49,0.208 10 false C31 5.208,0.938 5.656,1.115 0.448,0.177 10 false 93 5.208,0.542 5.656,0.719 0.448,0.177 10 false 92 5.219,1.323 5.667,1.5 0.448,0.177 10 false 91 5.531,0.635 6.021,0.844 0.49,0.208 10 false VPTK 5.521,1.125 6.01,1.333 0.49,0.208 10 false PTNK 5.521,1.385 6.01,1.594 0.49,0.208 10 false EPTK 1.479,2.656 5.302,2.854 3.823,0.198 10 false Vent Valve 1.417,3.802 5.24,4 3.823,0.198 10 false Leak Detection Pump 1.49,4.354 2.635,5.188 1.146,0.833 10 false Canister Pressure Sensor 1.823,5.625 3.333,6.042 1.51,0.417 10 false Canister Pump Module 1.344,5.625 2.854,6.042 1.51,0.417 10 false M60 1.146,2.417 1.594,2.594 0.448,0.177 10 false VLVB 3.073,2.417 3.521,2.594 0.448,0.177 10 false VGND 0.927,2.417 1.375,2.594 0.448,0.177 10 false 5 3.583,2.417 4.031,2.594 0.448,0.177 10 false 1 3.073,3.135 3.521,3.313 0.448,0.177 10 false MTRB 3.583,3.135 4.031,3.313 0.448,0.177 10 false 3 0.927,3.135 1.375,3.313 0.448,0.177 10 false 4 1.146,3.135 1.594,3.313 0.448,0.177 10 false MGND 3.167,4.198 3.615,4.375 0.448,0.177 10 false VCC 3.104,4.604 3.552,4.781 0.448,0.177 10 false VOUT 3.073,5.021 3.521,5.198 0.448,0.177 10 false SGND 3.583,4.198 4.031,4.375 0.448,0.177 10 false 6 3.583,4.615 4.031,4.792 0.448,0.177 10 false 7 3.573,5.021 4.021,5.198 0.448,0.177 10 false 8 5.167,2.51 5.656,2.719 0.49,0.208 10 false A40 5.188,3.708 5.677,3.917 0.49,0.208 10 false A40 5.177,4.302 5.667,4.51 0.49,0.208 10 false A40 5.177,4.719 5.667,4.927 0.49,0.208 10 false A40 5.188,5.125 5.677,5.333 0.49,0.208 10 false A40 5.188,6.365 5.688,6.573 0.5,0.208 10 false A40 5.208,2.323 5.656,2.5 0.448,0.177 10 false 39 5.229,3.531 5.677,3.708 0.448,0.177 10 false 38 5.219,4.104 5.667,4.281 0.448,0.177 10 false 55 5.219,4.531 5.667,4.708 0.448,0.177 10 false 40 5.229,4.948 5.677,5.125 0.448,0.177 10 false 54 5.219,6.177 5.667,6.354 0.448,0.177 10 false 53 5.531,2.417 6.021,2.625 0.49,0.208 10 false VPMP 5.521,3.615 6.01,3.823 0.49,0.208 10 false MPMP 5.521,4.198 6.01,4.406 0.49,0.208 10 false VCPP 5.521,4.708 6.01,4.917 0.49,0.208 10 false PPMP 5.51,5.031 6,5.24 0.49,0.208 10 false EPPM 5.531,6.281 6.021,6.49 0.49,0.208 10 false EMPM 5.875,8.281 6.365,8.49 0.49,0.208 10 false ECM 4.708,8.292 5.198,8.5 0.49,0.208 10 false A 6.302,4 6.75,4.177 0.448,0.177 10 false 5 V 6.313,0.385 6.76,0.563 0.448,0.177 10 false 5 V

A377771E01
2.094,1.177 6.375,1.375 4.281,0.198 10 false Fuel Vapor-containment Valve 2.094,1.031 2.875,1.208 0.781,0.177 10 false M61 2.531,0.76 3.313,0.938 0.781,0.177 10 false +B 3.021,0.76 3.802,0.938 0.781,0.177 10 false CCV 2.365,0.76 3.146,0.938 0.781,0.177 10 false 2 3.417,0.76 4.198,0.938 0.781,0.177 10 false 1 5.292,0.865 6.073,1.042 0.781,0.177 10 false A40 5.292,2.188 6.073,2.365 0.781,0.177 10 false C31 5.292,3.771 6.073,3.948 0.781,0.177 10 false A40 5.313,0.677 6.094,0.854 0.781,0.177 10 false 58 5.313,2.01 6.094,2.188 0.781,0.177 10 false 33 5.323,3.594 6.104,3.771 0.781,0.177 10 false 46 5.635,0.76 6.417,0.938 0.781,0.177 10 false CCV2 5.635,2.083 6.417,2.26 0.781,0.177 10 false PRG 5.646,3.677 6.427,3.854 0.781,0.177 10 false MREL 5.948,4.51 6.573,4.698 0.625,0.188 10 false ECM 2.74,2.427 3.51,2.698 0.771,0.271 10 false Purge VSV 2.417,2.427 3.198,2.604 0.781,0.177 10 false C11 2.583,2.094 3.365,2.271 0.781,0.177 10 false 2 3.25,2.083 4.031,2.26 0.781,0.177 10 false 1 3.5,2.865 4.271,3.135 0.771,0.271 10 false EFI NO. 3 4.292,3.49 5.063,3.76 0.771,0.271 10 false EFI NO. 2 2.125,4.427 6.406,4.625 4.281,0.198 10 false No. 1 Integration Relay 2.104,4.26 6.385,4.458 4.281,0.198 10 false 1B 2.052,3.24 2.833,3.417 0.781,0.177 10 false 3 2.052,3.667 2.833,3.844 0.781,0.177 10 false 5 3.521,3.24 4.302,3.417 0.781,0.177 10 false 4 3.521,3.677 4.302,3.854 0.781,0.177 10 false 6 2.531,4 3.302,4.271 0.771,0.271 10 false EFI-MAIN 1.104,3.49 1.875,3.76 0.771,0.271 10 false EFI-MAIN 0.448,3.865 1.219,4.135 0.771,0.271 10 false BATT-MAIN 0.583,4.719 1.625,5.052 1.042,0.333 10 false Auxiliary Battery 4.958,0.115 5.74,0.292 0.781,0.177 10 false A

CAUTION / NOTICE / HINT

NOTICE:
·

When a vehicle which has any of these DTCs stored is brought into the workshop, do not change the condition of the vehicle. For example, do not tighten the fuel tank cap assembly.

·

The GTS is required to conduct the following diagnostic troubleshooting procedure.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CONFIRM DTC AND EVAP PRESSURE
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) (do not start the engine).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

f.

Enter the following menus: Powertrain / Engine / Data List / Vapor Pressure Pump.

Powertrain > Engine > Data List
Tester Display
Vapor Pressure Pump
50003 372 160

g.

Read the EVAP (Evaporative Emission) pressure displayed on the GTS.

Result:
Display (DTC Output) Test Result Suspected Trouble Area Proceed to
P045011 Less than 42.11009 kPa(abs) [6.10596 psi(abs)]
·

Wire harness/connector (canister pressure sensor - ECM)

·

Canister pressure sensor

·

Short in ECM circuit


A
P045015 Higher than 123.76147 kPa(abs) [17.94541 psi(abs)]
·

Wire harness/connector (canister pressure sensor - ECM)

·

Canister pressure sensor

·

Open in ECM circuit


B
P04502F - Canister pressure sensor C




A

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

5.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

C

6.REPLACE CANISTER PUMP MODULE
2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Result:
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A40-40 (PPMP) - Body ground Always Below 10 Ω
·

Wire harness/connector (canister pressure sensor - ECM)

·

Short in canister pressure sensor circuit


A
10 kΩ or higher
·

Wire harness/connector (canister pressure sensor - ECM)

·

Short in ECM circuit


B




A

3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

4.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the canister pump module connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result:
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A40-40 (PPMP) - Body ground Always 10 kΩ or higher Short in canister pressure sensor circuit A
Below 10 Ω Short in wire harness/connector (canister pressure sensor - ECM) B




A

6.REPLACE CANISTER PUMP MODULE

B

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
5.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the canister pump module connector.

A376987C01
4.458,1.469 4.844,1.74 0.385,0.271 6.385,2.323 6.063,1.688 true 5.875,2.302 5.875,1.698 true 5.354,2.292 5.698,1.708 true 4.979,0.375 5.292,0.573 0.313,0.198 10 false *a 4.531,1.521 4.844,1.719 0.313,0.198 10 false M60 6.229,2.344 6.729,2.573 0.5,0.229 10 false SGND 5.219,2.333 5.719,2.563 0.5,0.229 10 false VCC 5.698,2.333 6.198,2.563 0.5,0.229 10 false VOUT
*a Front view of wire harness connector
(to Canister Pump Module)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M60-8 (SGND) - Body ground Always 100 Ω or less



c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M60-6 (VCC) - Body ground Power switch on (IG) 4.5 to 5.5 V
M60-7 (VOUT) - Body ground Power switch on (IG) 4.5 to 5.5 V


Result:
Test Result Suspected Trouble Area Proceed to
Voltage and resistance within standard ranges Open in canister pressure sensor circuit A
Voltage and/or resistance outside standard ranges Open in wire harness/connector (canister pressure sensor - ECM) B




A

6.REPLACE CANISTER PUMP MODULE

B

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
6.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module.

Click hereEngine / Hybrid System>2ZR-FXE EMISSION CONTROL>CANISTER(w/ Canister Pump Module)>REMOVAL

NOTICE:
·

When replacing the canister pump module, check the inside of the canister pump module and canister, and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the inside of the canister, replace the canister and canister pump module.

·

Check for filter blockage in the canister. If the charcoal filter inside the canister is clogged, replace the canister and canister pump module.

·

Check for filter blockage in the canister filter. If there is blockage in the canister filter, replace the canister filter.



A376983C01
4.802,6.354 5.021,6.354 5.021,6.354 5.167,5.823 true 4.552,5.906 4.771,5.906 4.771,5.906 4.948,5.531 true 5.656,5.51 5.448,5.51 5.448,5.51 5.229,5.375 true 1.708,2.094 1.927,2.094 1.927,2.094 2.438,3.063 true 5.406,2.688 5.198,2.688 5.198,2.688 4.74,3.063 true 5.313,3.292 5.104,3.292 5.104,3.292 4.604,3.74 true 5.688,1.479 5.479,1.479 5.479,1.479 5.188,1.833 true 2.896,5.865 3.115,5.865 3.115,5.865 3.844,3.406 true 4.771,4.604 4.948,4.604 4.948,4.604 5.167,4.313 true 2.552,5.458 2.771,5.458 2.771,5.458 3.688,3.26 true 2.74,5.781 3.052,5.938 0.313,0.156 10 false *1 5.708,5.448 6.021,5.604 0.313,0.156 10 false *2 4.615,4.521 4.927,4.677 0.313,0.156 10 false *3 1.552,2.01 1.865,2.167 0.313,0.156 10 false *4 5.354,3.208 5.667,3.365 0.313,0.156 10 false *5 5.448,2.615 5.76,2.771 0.313,0.156 10 false *6 4.396,5.823 4.708,5.979 0.313,0.156 10 false *7 2.385,5.375 2.698,5.531 0.313,0.156 10 false *8 4.646,6.25 4.854,6.458 0.208,0.208 10 false *9 5.75,1.406 6.219,1.563 0.469,0.156 10 false *10 4.26,0.771 4.573,0.927 0.313,0.156 10 false *a 6.135,4.688 6.448,4.844 0.313,0.156 10 false *a
*1 Fuel Tank Vent Hose *2 Air Inlet Port
*3 Vent Hose *4 Fuel Tank
*5 Canister Pump Module
·

Canister Pressure Sensor

·

Leak Detection Pump

·

Vent Valve


*6 Canister
*7 Canister Filter *8 Fuel Tank Pressure Sensor
*9 Fuel Tank Cap Assembly *10 Fuel Vapor-containment Valve
*a Inspection Area
(Check for disconnection and/or cracks)
- -



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
9.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
a.

Perform the Evaporative System Check using the GTS, referring to the Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P045011, P045015 or P04502F.


d.

Check the DTC judgment result.

Result:
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





Result:
Proceed to
NEXT



NEXT

END