Home › Engine / Hybrid System › 2ZR-FXE EMISSION CONTROL › CANISTER(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047497 2ZR-FXE EMISSION CONTROL _0236608 CANISTER(w/ Canister Pump Module) A

2ZR-FXE EMISSION CONTROL  CANISTER(w/ Canister Pump Module)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during canister (charcoal canister assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 17430 1.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Hide 58390 2.REMOVE NO. 1 FLOOR UNDER COVER ASSEMBLY

Hide 57628C 3.REMOVE REAR FLOOR SIDE MEMBER COVER LH

Hide 48832A 4.REMOVE REAR NO. 1 STABILIZER BAR BRACKET

a.
A377729

Remove the 4 bolts and rear No. 1 stabilizer bar bracket from the vehicle body.


Hide 77740 5.REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY)

a.
A377730C01
2.26,2.042 2.427,2.042 2.427,2.042 2.479,2.302 true 2.156,3.125 2.156,2.896 false 1.583,2.219 1.75,2.219 1.75,2.219 1.875,2.344 true 2.021,1.177 2.323,1.708 2.323,1.708 2.552,1.708 true 2.573,1.615 2.792,1.833 0.219,0.219 10 true *1 1.396,2.135 1.615,2.344 0.219,0.208 10 false *2 2.073,3.135 2.323,3.333 0.25,0.198 10 false *a 2.073,1.958 2.375,2.24 0.302,0.281 10 false *b
*1 Fuel Tank Vent Hose Sub-assembly
*2 Pipe (Leak Detection Pump Sub-assembly)
*a Tube Connector
*b O-ring
V100135

Pinch
V100136

Pull off


Disconnect the fuel tank vent hose sub-assembly from the leak detection pump sub-assembly.

NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the air line tube.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the air line tube.

·

If the tube connector and pipe are stuck, push and pull to release them.



i.

Push the fuel tank vent hose sub-assembly firmly toward the leak detection pump sub-assembly.


ii.

Pinch the tube connector as shown in the illustration.


iii.

Pull off the fuel tank vent hose sub-assembly from the pipe (leak detection pump sub-assembly).



b.
A377731

Disconnect the leak detection pump sub-assembly connector.


c.

Disconnect the fuel tank vent hose from the canister (charcoal canister assembly).

A377732C01
2.375,0.667 2.74,1.198 2.74,1.198 2.906,1.198 true 6.156,1.208 6.396,0.531 6.396,0.531 6.563,0.531 false 4.75,0.594 4.969,0.594 4.969,0.594 5.281,1.125 false 4.99,2.438 5.208,2.438 5.208,2.438 5.5,1.75 true 5.938,1.906 6.167,2.427 6.167,2.427 6.333,2.427 false 1.729,2.24 1.885,2.24 1.885,2.24 2.094,1.885 true 2.479,2.219 2.781,2.219 false 2.917,1.115 3.135,1.292 0.219,0.177 10 true *1 6.615,0.448 7.01,0.771 0.396,0.323 10 false *2 6.385,2.354 6.729,2.573 0.344,0.219 10 false *a 1.531,2.156 1.917,2.417 0.385,0.26 10 false *b 4.552,0.5 4.885,0.792 0.333,0.292 10 false *c 4.781,2.354 5.167,2.573 0.385,0.219 10 false *d 2.823,2.135 3.167,2.354 0.344,0.219 10 false *a
*1 Fuel Tank Vent Hose *2 Pipe (Canister (Charcoal Canister Assembly))
*a Retainer *b Tab
*c Tube Connector *d O-ring
V100135

Pinch
V100136

Pull off


NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the fuel tank vent hose.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose.

·

If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.



HINT:

Do not remove the retainer.


i.

Pinch the tabs of the retainer to disengage the lock claws and pull it down.


ii.

Pull off the fuel tank vent hose.



d.
A377734

Slide the clip and disconnect the purge line hose from the canister (charcoal canister assembly).


e.
A377735

Remove the bolt.


f.
A377736

Remove the canister (charcoal canister assembly) from vehicle body as shown in the illustration.


Hide 77740R 6.REMOVE LEAK DETECTION PUMP SUB-ASSEMBLY

HINT:

Only perform this procedure when replacement of the leak detection pump sub-assembly is necessary.


a.

Before removing the leak detection pump sub-assembly, clean the charcoal canister sub-assembly by blowing air into it to ensure that the charcoal canister sub-assembly is free of foreign matter.

NOTICE:
·

Make sure to clean the charcoal canister sub-assembly using air only.

·

Do not use gasoline, thinners or solvents.




b.
A377738C01
1.146,1.781 0.813,1.5 0.813,1.5 0.594,1.5 false 0.396,1.406 0.719,1.667 0.323,0.26 10 false *a
*a Protective Tape


While disengaging the 2 claws as shown in the illustration, push the leak detection pump sub-assembly upwards using a screwdriver with its tip wrapped with protective tape to remove it.


c.

Check if the charcoal canister sub-assembly contains foreign matter such as mud or water.

i.
A377739

Visually check that the inside of the charcoal canister sub-assembly is free of foreign matter.


ii.

Hold the charcoal canister sub-assembly upside down to make sure that it is free of foreign matter.

If the charcoal canister sub-assembly contains foreign matter, replace the canister (charcoal canister assembly).