Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0236137 SFI SYSTEM(w/ Canister Pump Module) J

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the power switch is turned on (IG), the MIL should be illuminated and should then turn off after the power switch is turned on (READY). If the MIL remains illuminated or is does not illuminate, conduct the following troubleshooting procedure.

WIRING DIAGRAM

A380767E02
1.281,0.906 1.896,1.104 0.615,0.198 10 false CANH 2.865,0.906 3.479,1.104 0.615,0.198 10 false CA5H 3.927,0.906 4.542,1.104 0.615,0.198 10 false CA2H 5.521,0.906 6.135,1.104 0.615,0.198 10 false CAN+ 1.292,1.375 1.906,1.573 0.615,0.198 10 false CANL 2.854,1.365 3.469,1.563 0.615,0.198 10 false CA5L 3.927,1.375 4.542,1.573 0.615,0.198 10 false CA2L 5.521,1.365 6.135,1.563 0.615,0.198 10 false CAN- 1.75,0.75 2.292,0.927 0.542,0.177 10 false 26 2.615,0.75 3.156,0.927 0.542,0.177 10 false 15 5.281,0.76 5.823,0.938 0.542,0.177 10 false 31 4.396,0.75 4.938,0.927 0.542,0.177 10 false 22 2.615,1.208 3.156,1.385 0.542,0.177 10 false 16 1.74,1.208 2.281,1.385 0.542,0.177 10 false 27 4.396,1.208 4.938,1.385 0.542,0.177 10 false 7 5.302,1.208 5.844,1.385 0.542,0.177 10 false 32 4.458,1.979 5.396,2.229 0.938,0.25 10 false to Other ECUs 1.802,1.99 2.74,2.24 0.938,0.25 10 false to Other ECUs 0.063,2.479 0.958,2.646 0.896,0.167 10 false F6 0.042,2.646 1.865,3.042 1.823,0.396 10 false Combination Meter Assembly (Meter Circuit Plate) 2.917,2.521 3.813,2.688 0.896,0.167 10 false F59 2.906,2.677 4.729,3.073 1.823,0.396 10 false Network Gateway ECU 5.927,2.542 6.25,2.76 0.323,0.219 10 false C31 6.292,2.531 6.688,2.729 0.396,0.198 10 false ECM 0.927,3.229 2.75,3.625 1.823,0.396 10 false : CAN Communication Line

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
MIL Condition Proceed to
Illuminates → Turns off Power switch on (IG) → Power switch on (READY) A
Other than above - B




A

B

2.CHECK COMMUNICATION BETWEEN GTS AND ECM
2.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

Communication can be checked by using the Data List item Engine.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check if any DTCs have been detected. Note down any DTCs.

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

4.PERFORM ACTIVE TEST USING GTS

B

REPAIR CIRCUIT INDICATED BY OUTPUT

4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Indicator
50004 122 150

e.

According to the display on the GTS, perform the Active Test and check the operation of the MIL.

Result:
Result Proceed to
Changes A
Does not change B




A

B