Home › Engine / Hybrid System › 2ZR-FXE INTAKE / EXHAUST › EXHAUST PIPE
RM3210E _51 Engine / Hybrid System _047498 2ZR-FXE INTAKE / EXHAUST _0236619 EXHAUST PIPE A

2ZR-FXE INTAKE / EXHAUST  EXHAUST PIPE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of heated oxygen sensor (w/ Canister Pump Module)

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 51444C 1.REMOVE REAR MOTOR UNDER COVER LH (w/ Exhaust Heat Recirculation System)

Hide 3.DRAIN ENGINE COOLANT (w/ Exhaust Heat Recirculation System)

Hide 58166 4.REMOVE FRONT FLOOR COVER LH

Hide 58165B 5.REMOVE FRONT FLOOR COVER RH

Hide 57533B 6.REMOVE FRONT CENTER FLOOR BRACE

a.
A376903

Remove the 8 bolts and 2 front center floor braces from the vehicle body.


Hide 17430 7.REMOVE TAIL EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.

Remove the 2 bolts and 2 compression springs and disconnect the tail exhaust pipe assembly from the front exhaust pipe assembly (TWC: Rear Catalyst).

A378797C01
0.552,0.052 0.927,0.396 0.375,0.344 12 false *A 3.896,0.063 4.24,0.396 0.344,0.333 12 false *B
*A w/ Exhaust Heat Recirculation System *B w/o Exhaust Heat Recirculation System



b.

Remove the tail exhaust pipe assembly from the 4 exhaust pipe supports.


c.

Remove the exhaust pipe gasket from the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 17410 8.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.

w/ Exhaust Heat Recirculation System:

i.
A376891C01
2.271,1.01 2.563,1.792 2.563,1.792 2.771,1.792 true 1.938,1.01 2.292,0.458 2.292,0.458 2.5,0.458 true 1.854,1.271 1.729,2.031 1.729,2.031 1.531,2.031 true 1.594,1 1.375,0.417 1.375,0.417 1.177,0.417 true 2.521,0.375 2.729,0.552 0.208,0.177 10 true *a 2.792,1.708 2.99,1.896 0.198,0.188 10 true *b 1.302,1.948 1.521,2.135 0.219,0.188 10 true *1 0.969,0.354 1.188,0.542 0.219,0.188 10 true *2
*1 Outlet Heater Water Hose B
*2 Outlet Heater Water Hose C
*a No. 2 Outlet Water Pipe
*b Inlet Water Pipe


Slide the 2 clips and disconnect the outlet heater water hose B and outlet heater water hose C from the inlet water pipe and No. 2 outlet water pipe.



b.
A378795C01
0.042,0.042 0.313,0.271 0.271,0.229 12 true *A 0.063,2.396 0.323,2.604 0.26,0.208 12 true *B
*A w/ Exhaust Heat Recirculation System
*B w/o Exhaust Heat Recirculation System


Remove the 2 bolts and 2 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold (TWC: Front Catalyst).


c.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.


d.

Remove the exhaust pipe gasket from the exhaust manifold (TWC: Front Catalyst).