Home › Engine / Hybrid System › 2ZR-FXE INTAKE / EXHAUST › INTAKE MANIFOLD
RM3210E _51 Engine / Hybrid System _047498 2ZR-FXE INTAKE / EXHAUST _0236617 INTAKE MANIFOLD A

2ZR-FXE INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT (w/ Stud Bolt)

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A376881

Using an E6 "TORX" socket wrench, install the 2 stud bolts to the intake manifold.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17177 2.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.

Install a new No. 1 intake manifold to head gasket to the intake manifold.


Hide 17111 3.INSTALL INTAKE MANIFOLD

a.

Temporarily install the intake manifold to the cylinder head sub-assembly with the 3 bolts and 2 nuts.


b.
A376879C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Tighten the 3 bolts and 2 nuts in several steps.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 4.CONNECT WATER BY-PASS HOSE

a.
A376878C01
0.427,0.365 0.583,0.365 0.583,0.365 0.688,0.667 true 1.969,0.208 1.833,0.208 1.833,0.208 1.698,0.51 true 1.979,0.115 2.198,0.302 0.219,0.188 10 true *1 0.24,0.281 0.448,0.469 0.208,0.188 10 true *2
*1 Water By-Pass Hose
*2 No. 2 Water By-pass Hose


Engage the 2 hose clamps to connect the No. 2 water by-pass hose to the intake manifold.


b.

Engage the 2 hose clamps to connect the water by-pass hose to the intake manifold.


Hide 23827A 5.CONNECT NO. 2 FUEL VAPOR FEED HOSE

a.

Engage the 2 hose clamps to connect the No. 2 fuel vapor feed hose to the intake manifold.


b.

Connect the No. 2 fuel vapor feed hose to the intake manifold.


Hide 16296 6.CONNECT NO. 8 WATER BY-PASS HOSE

a.

Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.


b.

Engage the 2 hose clamps.


Hide 12631A 7.CONNECT ENGINE COVER BRACKET

a.

Connect the engine cover bracket to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82121 8.CONNECT ENGINE WIRE

a.
A376874

Engage the clamp and connect the engine wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the 4 fuel injector assembly connectors and purge valve (purge VSV) connectors.


c.
A376873

Connect the wire harness bracket with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.
A376872

Connect the engine water pump assembly connector.


e.

Engage the 2 clamps.


Hide 12261 9.CONNECT VENTILATION HOSE

a.

Connect the ventilation hose to the intake manifold and slide the clip to secure it.


Hide 89421 10.INSTALL E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

a.

Install the E.F.I. vacuum sensor assembly (manifold absolute pressure sensor) to the intake manifold with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the vacuum hose to the intake manifold.


c.

Connect the E.F.I. vacuum sensor assembly (manifold absolute pressure sensor) connector.


Hide 25610 11.INSTALL EGR PIPE ASSEMBLY

a.
A378754C01
2.302,0.969 2.719,0.74 2.719,0.74 2.354,1.281 true 0.74,0.5 0.521,0.458 0.521,0.458 0.656,0.938 true 0.344,0.302 0.531,0.5 0.188,0.198 10 true *a 2.729,0.615 2.917,0.813 0.188,0.198 10 true *a
*a Claw


Install a new EGR pipe gasket to the EGR valve assembly.

NOTICE:

Make sure that the claws of the EGR valve gasket are toward the EGR valve assembly side.



b.
A378755C01
1.146,1.094 1.531,1.094 true 1.927,1.813 2.083,1.813 2.083,1.813 2.281,1.25 true 0.948,0.979 1.146,1.198 0.198,0.219 10 true *a 1.719,1.729 1.938,1.938 0.219,0.208 10 true *b
*a Groove
*b Protrusion


Install a new inlet EGR gasket to the intake manifold.

HINT:

Align the protrusion of the inlet EGR gasket with the groove of the intake manifold.



c.

Install the EGR pipe assembly to the intake manifold and EGR valve assembly with the 4 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 17751 12.INSTALL INLET NO. 1 AIR CLEANER

a.

Install the inlet No. 1 air cleaner to the intake manifold with the 2 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 17771A 13.INSTALL AIR CLEANER BRACKET

a.
A376866C02
2.354,0.323 2.573,0.531 0.219,0.208 10 true *a 0.979,1.042 1.188,1.25 0.208,0.208 10 true *b 1.385,0.208 1.583,0.396 0.198,0.188 10 true *b
*a Bolt (A)
*b Bolt (B)


Engage the wire harness clamp and install the air cleaner bracket to the cylinder block sub-assembly and air conditioning wire with the bolt (A) and 2 bolts (B).

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17701 14.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly to the air cleaner bracket with the 2 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 17801 15.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 17752 16.INSTALL INLET NO. 2 AIR CLEANER

a.
A378753C01
3.146,1.135 3.146,0.552 true 2.594,1.135 2.594,0.552 true 2.49,1.135 2.708,1.344 0.219,0.208 10 true *a 3.063,1.146 3.271,1.354 0.208,0.208 10 true *b
*a Groove
*b Protrusion


Temporarily install the inlet No. 2 air cleaner to the inlet No. 1 air cleaner and upper radiator support sub-assembly with the 2 bolts.

HINT:

Align the protrusion of the inlet No. 1 air cleaner with the groove of the inlet No. 2 air cleaner.



b.

Tighten the 2 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Tighten the hose clamp.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 53289A 17.INSTALL RADIATOR SUPPORT OPENING COVER

Hide 22210 18.INSTALL THROTTLE BODY ASSEMBLY