Home › Engine / Hybrid System › 2ZR-FXE INTAKE / EXHAUST › EXHAUST MANIFOLD
RM3210E _51 Engine / Hybrid System _047498 2ZR-FXE INTAKE / EXHAUST _0236618 EXHAUST MANIFOLD A

2ZR-FXE INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold (TWC: Front Catalyst) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 89467B 1.REMOVE AIR FUEL RATIO SENSOR

Hide 51444C 2.REMOVE REAR MOTOR UNDER COVER LH (w/ Exhaust Heat Recirculation System)

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442 4.REMOVE NO. 2 ENGINE UNDER COVER

Hide 5.DRAIN ENGINE COOLANT (w/ Exhaust Heat Recirculation System)

Hide 58166 6.REMOVE FRONT FLOOR COVER LH

a.
A376888C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Remove the 2 bolts and 3 clips and disengage the 5 clamps to remove the front floor cover LH from the vehicle body.


Hide 58165B 7.REMOVE FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.


Hide 57533B 8.REMOVE FRONT CENTER FLOOR BRACE

a.
A376889

Remove the 12 bolts and 3 front center floor braces from the vehicle body.


Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.

w/ Exhaust Heat Recirculation System:

i.
A376891C01
2.271,1.01 2.563,1.792 2.563,1.792 2.771,1.792 true 1.938,1.01 2.292,0.458 2.292,0.458 2.5,0.458 true 1.854,1.271 1.729,2.031 1.729,2.031 1.531,2.031 true 1.594,1 1.375,0.417 1.375,0.417 1.177,0.417 true 2.521,0.375 2.729,0.552 0.208,0.177 10 true *a 2.792,1.708 2.99,1.896 0.198,0.188 10 true *b 1.302,1.948 1.521,2.135 0.219,0.188 10 true *1 0.969,0.354 1.188,0.542 0.219,0.188 10 true *2
*1 Outlet Heater Water Hose B
*2 Outlet Heater Water Hose C
*a No. 2 Outlet Water Pipe
*b Inlet Water Pipe


Slide the 2 clips and disconnect the outlet heater water hose B and outlet heater water hose C from the inlet water pipe and No. 2 outlet water pipe.



b.
A378756

Disconnect the heated oxygen sensor connector.


c.

Disengage the wire harness clamp.


d.
A378758C01
0.063,0.063 0.292,0.281 0.229,0.219 10 true *A 0.052,2.396 0.302,2.615 0.25,0.219 12 true *B
*A w/ Exhaust Heat Recirculation System
*B w/o Exhaust Heat Recirculation System


Remove the 4 bolts and 4 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold (TWC: Front Catalyst) and tail exhaust pipe assembly.


e.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.


f.

Remove the 2 exhaust pipe gaskets from the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 82715 10.REMOVE WIRING HARNESS CLAMP BRACKET

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A376894

Disengage the clamp and remove the bolt and wiring harness clamp bracket from the cylinder head sub-assembly.


Hide 17167 11.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A376897

Remove the 6 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst).


Hide 17118 12.REMOVE MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A376898

Remove the 3 bolts and manifold stay from the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly.


Hide 17141 13.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.

w/ Exhaust Heat Recirculation System:

i.
A376895

Remove the nut and disconnect the water pipe and hose sub-assembly A from the bracket.


ii.

Disconnect the engine coolant temperature sensor connector.



b.

for LHD:

i.
A376896C01
0,0 0,0 false
V113147

Release
V113148

Disconnect


Release the lock lever and disconnect the brake booster pump assembly connector as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



ii.

Disengage the clamp.



c.
A376899

Remove the 7 nuts and exhaust manifold (TWC: Front Catalyst) from the cylinder head sub-assembly.


d.
A376909C01
2.188,1.438 2.063,1.438 2.063,1.438 1.969,1.01 true 0.26,1.344 0.417,1.344 0.417,1.344 0.521,0.906 true 2.208,1.354 2.438,1.573 0.229,0.219 10 true *1 0.083,1.26 0.271,1.458 0.188,0.198 10 true *2
*1 Exhaust Manifold To Head Gasket
*2 EGR Cooler Gasket


Remove the exhaust manifold to head gasket and EGR cooler gasket from the cylinder head sub-assembly.


Hide 17168 14.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A376900

Remove the 4 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst).