Home › Engine / Hybrid System › 2ZR-FXE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM3210E _51 Engine / Hybrid System _047495 2ZR-FXE ENGINE MECHANICAL _0244906 ENGINE ASSEMBLY A

2ZR-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
for SFI system (w/ Canister Pump Module)

Replacement of ECM


Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
for SFI system (w/o Canister Pump Module)

Replacement of ECM


Perform Vehicle Identification Number (VIN) or frame number registration (Click here)
for SFI system (w/ Canister Pump Module)
·

Replacement of throttle body assembly

·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
for SFI system (w/o Canister Pump Module)
·

Replacement of throttle body assembly

·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple advanced parking guidance system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

The vehicle has a hybrid system that operates at voltages up to 650 V. The hybrid system uses an HV battery that contains an electrolyte which is a strong alkali solution that includes potassium hydroxide. Be sure to follow the instructions in this manual to handle the system correctly. Failure to do so may result in serious injury or electrocution.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.SECURE STEERING WHEEL

Hide 5.REMOVE FRONT WHEELS

Hide 51441 6.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the 10 clips, 4 bolts and No. 1 engine under cover.


Hide 51444C 7.REMOVE REAR MOTOR UNDER COVER LH

a.

except Rough Road Area Specification Vehicles:

i.

Remove the 4 clips, screw and rear motor under cover LH.



b.

for Rough Road Area Specification Vehicles:

i.

Remove the 5 clips, screw and rear motor under cover LH.



Hide 51443E 8.REMOVE REAR MOTOR UNDER COVER RH

a.

except Rough Road Area Specification Vehicles:

i.

Remove the 4 clips, screw and rear motor under cover RH.



b.

for Rough Road Area Specification Vehicles:

i.

Remove the 5 clips, screw and rear motor under cover RH.



Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

a.

Remove the 3 bolts and No. 2 engine under cover.


Hide 11.DRAIN ENGINE COOLANT (for Engine)

Hide 12601B 13.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

Disengage the 3 clips in the order shown in the illustration to remove the No. 1 engine cover sub-assembly.

A385900C02
3.469,1.115 3.625,1.313 0.156,0.198 10 true 1 2.698,0.667 2.854,0.865 0.156,0.198 10 true 2 3.927,0.813 4.083,1.01 0.156,0.198 10 true 3
V100155

Areas to be Held when Lifting No. 1 Engine Cover Sub-assembly
V113147

Remove in this Direction


NOTICE:
·

Pull the No. 1 engine cover sub-assembly straight up to remove. Attempting to pull the No. 1 engine cover sub-assembly forward or attempting to pull it up by holding the left and right sides may cause the No. 1 engine cover sub-assembly to break.

·

If the clips are not disengaged in the order shown in the illustration, the No. 1 engine cover sub-assembly may be damaged.




Hide 16296 14.DISCONNECT NO. 8 WATER BY-PASS HOSE

a.
A375788

Slide the clip and disconnect the No. 8 water by-pass hose from the No. 2 water by-pass hose assembly.


Hide 53289A 15.REMOVE RADIATOR SUPPORT OPENING COVER

Hide 17752 16.REMOVE INLET NO. 2 AIR CLEANER

Hide 22210 17.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17801 18.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 19.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 17771A 20.REMOVE AIR CLEANER BRACKET

Hide 17751 21.REMOVE INLET NO. 1 AIR CLEANER

Hide G9200 22.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 16573B 23.DISCONNECT NO. 3 RADIATOR HOSE

a.
A372567

Remove the 2 bolts from the hybrid vehicle transaxle assembly.


b.

Slide the clip and disconnect the No. 3 radiator hose from the water outlet.


Hide 16572D 24.DISCONNECT NO. 2 RADIATOR HOSE

a.
A372568

Slide the clip and disconnect the No. 2 radiator hose from the water inlet sub-assembly.


Hide 87246E 25.DISCONNECT OUTLET HEATER WATER HOSE E

a.
A372572

Slide the clip and disconnect the outlet heater water hose E from the No. 1 water by-pass pipe.


Hide 87245A 26.DISCONNECT INLET HEATER WATER HOSE A

a.
A372573

Slide the clip and disconnect the inlet heater water hose A from the EGR valve assembly.


Hide 23826 27.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A372574

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the fuel vapor feed pipe.


Hide 23901 28.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide G922H 29.DISCONNECT INLET HYBRID RADIATOR HOSE

a.
A372569

Slide the clip and disconnect the inlet hybrid radiator hose from the motor cooling cooler.


Hide G922F 30.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

a.
A372570

Slide the clip and disconnect the outlet No. 1 hybrid water pump hose from the motor cooling cooler.


Hide 88370 31.SEPARATE COMPRESSOR WITH MOTOR ASSEMBLY

a.
E336863C03
1.208,0.76 1.667,1.031 true 1.708,0.948 1.906,1.125 0.198,0.177 10 true *a
*a Bracket


Remove the bolt and disconnect the bracket.


b.
E336866C03
1.281,0.542 1.531,0.271 true 2.469,2.146 2.719,1.875 true 2.5,2.646 2.781,2.979 true 2.781,1.813 3.094,1.969 0.313,0.156 10 false *a 2.833,2.927 3.146,3.083 0.313,0.156 10 false *b 1.583,0.208 1.896,0.365 0.313,0.156 10 false *c
*a Connector (A)
*b Connector (B)
*c Green-colored Lock


Using a screwdriver, slide the green-colored lock of the connector (A) as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Insulate the disconnected terminals and connector with insulating tape.



c.

Disconnect the connector (B).


d.
E336864

Remove the 3 bolts and separate the compressor with motor assembly.


Hide 82123 32.DISCONNECT NO. 3 ENGINE WIRE

a.
A372560

Disengage the clamp.


b.

Remove the bolt and disconnect the No. 3 engine wire from the hybrid vehicle transaxle assembly.


Hide 45259A 33.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 34.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 35.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 58166 36.REMOVE FRONT FLOOR COVER LH

Hide 58165B 37.REMOVE FRONT FLOOR COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 57533B 38.REMOVE FRONT CENTER FLOOR BRACE

Hide 17410 39.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 43502H 40.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 41.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure as for the LH side.


Hide 89543 42.SEPARATE FRONT SPEED SENSOR LH

Hide 89542 43.SEPARATE FRONT SPEED SENSOR RH

HINT:

Use the same procedure as for the LH side.


Hide 45047 44.SEPARATE TIE ROD END SUB-ASSEMBLY LH

Hide 45046 45.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 48810 46.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 47.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 48069 48.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 49.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 43420 50.SEPARATE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 51.SEPARATE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 43420 52.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 53.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 43420G 54.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

Hide 51108A 55.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 56.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 57.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A372561C01
0,0 0,0 false
V100155

Attachment Installation Position


Place height adjustment attachments and plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.
A372577

Remove the nut.


c.

Remove the 2 bolts and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


d.
A372578

Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.


e.
A380140

Remove the bolt and No. 2 engine mounting stay LH.


f.
A375843

Remove the 4 bolts and separate the front suspension crossmember sub-assembly from the vehicle body.


g.

Operate the engine lifter to remove the engine assembly with transaxle from the vehicle body.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle body.




Hide 82715 58.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A379357

Disengage the 3 clamps.


b.

Remove the bolt and wiring harness clamp bracket from the cylinder head sub-assembly.


Hide 59.INSTALL ENGINE HANGERS

a.
A372562C01
1.75,1.083 2.063,1.083 true 1.271,1.896 1.417,1.896 1.417,1.896 1.677,1.563 true 2,3.135 2.313,3.135 true 1.385,4.229 1.531,4.229 1.531,4.229 1.792,3.896 true 2.135,1.01 2.448,1.208 0.313,0.198 10 true *1 2.385,3.042 2.698,3.24 0.313,0.198 10 true *2 1,1.802 1.25,2 0.25,0.198 10 true *3 1.104,4.146 1.354,4.344 0.25,0.198 10 true *3
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
*3 Bolt


Install the No. 1 engine hanger and No. 2 engine hanger with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-37021
No. 2 Engine Hanger 12282-37011
Bolt 91552-81050



b.

Using an engine sling device and engine lifter, secure the engine assembly with transaxle.

NOTICE:
·

Adjust the angle of the sling device carefully to prevent damage or deformation to the engine hangers or engine assembly.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 12372A 60.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A372579

Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle body.


Hide 12305 61.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A379827

Remove the 2 bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH and vehicle body.


b.
A372580

Remove the bolt, nut and disconnect the 2 cooler brackets.


c.

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle body.


Hide 11363A 63.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 82121 64.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly with transaxle.


Hide 31270 66.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 68.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.

NOTICE:
·

Adjust the angle of the sling device carefully to prevent the engine assembly or engine hangers from deforming or becoming damaged.

·

Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.




Hide 69.REMOVE ENGINE HANGERS

a.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.