Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0236932 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly (meter circuit plate) detects a fuel sender gauge assembly malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1500 Fuel Sender Open Detected When IG voltage is 9.5 V or more and the following condition is detected:
·

Voltage signal from fuel sender gauge assembly is 0.2 V or less 3 times consecutively

·

Voltage signal from fuel sender gauge assembly is 4.7 V or more 3 times consecutively


·

Harness or connector

·

Fuel suction tube with pump and gauge assembly

·

Fuel sender gauge assembly

·

Combination meter assembly (Meter circuit plate)


- -

WIRING DIAGRAM

E285369E06
0.115,2.646 0.448,2.813 0.333,0.167 10 false M10 0.115,2.813 3.865,3.219 3.75,0.406 10 false Fuel Suction Tube with Pump and Gauge Assembly 5.208,2.625 5.583,2.833 0.375,0.208 10 false F6 5.208,2.792 7.021,3.344 1.813,0.552 10 false Combination Meter Assembly (Meter Circuit Plate) 0.781,1.479 1.25,1.667 0.469,0.188 10 false Sender 1.688,1.188 1.833,1.354 0.146,0.167 10 false 1 1.688,1.844 1.833,2.01 0.146,0.167 10 false 2 2.333,0.74 2.479,0.906 0.146,0.167 10 false 3 2.333,1.406 2.479,1.573 0.146,0.167 10 false 1 2.323,2.083 2.469,2.25 0.146,0.167 10 false 2 2.021,2.083 2.271,2.25 0.25,0.167 10 false FE 2.042,1.406 2.292,1.573 0.25,0.167 10 false FV 2.031,0.74 2.688,1.021 0.656,0.281 10 false FR 5.458,0.74 5.708,0.906 0.25,0.167 10 false 29 5.469,1.406 5.719,1.573 0.25,0.167 10 false 31 5.469,2.083 5.719,2.25 0.25,0.167 10 false 30 5.74,0.833 6.156,1.135 0.417,0.302 10 false FR 5.74,1.5 5.99,1.667 0.25,0.167 10 false FV 5.75,2.208 6.188,2.448 0.438,0.24 10 false FE&B 0.802,1.313 1.115,1.49 0.313,0.177 10 false Fuel 0.781,1.646 1.229,1.854 0.448,0.208 10 false Gauge 0.781,1.813 1.417,2 0.635,0.188 10 false Assembly 1.813,1.396 1.958,1.563 0.146,0.167 10 false 3

PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0 L, Max.: 127.5 L w/ Canister Pump Module:
Fuel receiver gauge indicates F (1/1): 38.3 L
Fuel receiver gauge indicates 3/4: 29.8 L
Fuel receiver gauge indicates 1/2: 21.3 L
Fuel receiver gauge indicates 1/4: 12.8 L
Fuel receiver gauge indicates E (R): 4.3 L
w/o Canister Pump Module:
Fuel receiver gauge indicates F (1/1): 38.3 L
Fuel receiver gauge indicates 3/4: 29.9 L
Fuel receiver gauge indicates 1/2: 21.4 L
Fuel receiver gauge indicates 1/4: 12.8 L
Fuel receiver gauge indicates E (R): 4.3 L
Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data can be displayed on the GTS and DTC B1500 is output. A
Fuel level data cannot be displayed on the GTS. B



A

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

B

2.INSPECT FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)
2.INSPECT FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)
a.
E284677C14
1.5,0.208 1.906,0.458 0.406,0.25 1.667,1.125 2.115,1.719 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.635,0.25 1.938,0.479 0.302,0.229 10 false F6 2.177,1.74 2.49,1.896 0.313,0.156 10 false FV
*a Component with harness connected
(Combination Meter Assembly (Meter Circuit Plate))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-31 (FV) - Body ground Power switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

3.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
E284677C15
1.5,0.208 1.906,0.458 0.406,0.25 1.875,1.115 2.208,1.698 true 1.76,1.125 1.292,1.708 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.635,0.25 1.979,0.479 0.344,0.229 10 false F6 1.042,1.75 1.552,1.958 0.51,0.208 10 false FE&B 2.146,1.75 2.458,1.906 0.313,0.156 10 false FR
*a Component with harness connected
(Combination Meter Assembly (Meter Circuit Plate))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-29 (FR) - F6-30 (FE&B) Power switch on (IG) 0.3 to 4.6 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
a.

Disconnect the F6 combination meter assembly (meter circuit plate) connector.


b.

Disconnect the M10 fuel suction tube with pump and gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-29 (FR) - M10-3 (FR) Always Below 1 Ω
F6-30 (FE&B) - M10-2 (FE) Always Below 1 Ω
F6-31 (FV) - M10-1 (FV) Always Below 1 Ω
F6-29 (FR) or M10-3 (FR) - Body ground Always 10 kΩ or higher
F6-30 (FE&B) or M10-2 (FE) - Body ground Always 10 kΩ or higher
F6-31 (FV) or M10-1 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL SENDER GAUGE ASSEMBLY

b.

Inspect the fuel sender gauge assembly.

w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE FUEL>FUEL SENDER GAUGE ASSEMBLY(w/ Canister Pump Module)>INSPECTION

w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE FUEL>FUEL SENDER GAUGE ASSEMBLY(w/o Canister Pump Module)>INSPECTION

OK:

Fuel sender gauge assembly is normal.



Result:
Proceed to
OK
NG



OK

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
a.
E158805C05
0.313,1.333 0.74,1.635 0.427,0.302 0.313,3.667 0.729,3.958 0.417,0.292 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.5,1.417 0.833,1.667 0.333,0.25 10 false A 0.5,3.74 0.833,3.99 0.333,0.25 10 false B
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 - B-1 Always Below 1 Ω
A-1 - B-3 Always Below 1 Ω
A-2 - B-2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY