Home › Engine / Hybrid System › 2ZR-FXE FUEL › FUEL PUMP(w/ Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047496 2ZR-FXE FUEL _0241960 FUEL PUMP(w/ Canister Pump Module) A

2ZR-FXE FUEL  FUEL PUMP(w/ Canister Pump Module)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump with filter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of fuel pump with filter assembly Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58415E 4.REMOVE REAR NO. 1 FLOOR BOARD

Hide 58432D 5.REMOVE DECK BOARD RETAINER

Hide 64997 6.REMOVE DECK FLOOR BOX LH (w/o Spare Tire)

Hide 64995 7.REMOVE DECK FLOOR BOX RH (w/o Spare Tire)

Hide 64993 8.REMOVE REAR DECK FLOOR BOX (w/ Compact Spare Tire)

Hide 64997 9.REMOVE DECK FLOOR BOX LH (w/ Compact Spare Tire)

Hide 64995 10.REMOVE DECK FLOOR BOX RH (w/ Compact Spare Tire)

Hide 64995 11.REMOVE DECK FLOOR BOX RH (w/ Full Size Spare Tire)

Hide 64997 12.REMOVE DECK FLOOR BOX LH (w/ Full Size Spare Tire)

Hide 13.REMOVE REAR SEAT ASSEMBLY

Hide 899A0B 14.REMOVE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

Hide 71305A 15.REMOVE CENTER REAR SEATBACK HINGE SUB-ASSEMBLY

a.
A374352

Remove the 2 bolts and center rear seatback hinge sub-assembly from the vehicle body.


Hide 82818B 16.REMOVE NO. 3 WIRING HARNESS PROTECTOR

a.
A374314

Remove the No. 3 wiring harness protector from the rear floor service hole cover.


Hide 58325E 17.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A374588C01
1.333,0.5 1.458,0.198 1.458,0.198 1.583,0.198 true 1.625,0.125 1.833,0.271 0.208,0.146 10 true *a
*a Protective Tape


Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.


b.
A374317

Disconnect the fuel pump connector and fuel tank pressure sensor (vapor pressure sensor) connector.


Hide 89461 18.REMOVE FUEL TANK PRESSURE SENSOR (VAPOR PRESSURE SENSOR)

Hide 77404 19.DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

a.
A374372

Disconnect the fuel tank vent hose sub-assembly from the fuel suction tube with pump and gauge assembly.

Click hereEngine / Hybrid System>2ZR-FXE FUEL>FUEL SYSTEM>PRECAUTION


Hide 77209F 20.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A374373C01
1.125,1.177 1.125,0.729 true 2.229,1.698 2.229,1.323 true 1.26,2.479 1.417,2.479 1.417,2.479 1.542,2.781 false 2.104,2.771 2.24,2.448 2.24,2.448 2.354,2.448 false 0.979,3.771 1.073,3.771 1.073,3.771 1.229,3.427 false 2.479,3.25 2.656,3.25 false 2.198,3.417 2.656,3.417 2.656,3.417 2.656,3.563 false 2.188,3.563 2.74,3.563 false 0.813,3.698 1.125,3.854 0.313,0.156 10 false *1 2.156,1.719 2.333,1.885 0.177,0.167 10 true *2 1.052,1.198 1.219,1.385 0.167,0.188 10 true *3 2.396,2.365 2.708,2.521 0.313,0.156 10 false *a 2.781,3.479 3.094,3.635 0.313,0.156 10 false *b 1.104,2.396 1.417,2.552 0.313,0.156 10 false *c 2.698,3.177 3.01,3.333 0.313,0.156 10 false *2
*1 Fuel Suction Plate Sub-assembly
*2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly
*a Fuel Tube Joint
*b O-ring
*c Nylon Tube
V100135

Pull off
V100136

Pull off


Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.




Hide 77144 21.REMOVE FUEL PUMP GAUGE RETAINER

a.
A374374C01
0,0 0,0 false
V100135

Front Side


Disengage the claw to remove the No. 1 fuel tube clamp.


b.

Remove the fuel pump gauge retainer.

i.
A374375C01
0.99,0.281 1.521,0.281 true 2.604,0.604 2.781,0.604 true 1.958,1.125 2.5,1.125 true 1.958,2.042 1.958,1.604 true 0.854,3.094 1.625,3.094 true 1.667,3.01 1.833,3.188 0.167,0.177 10 true *a 2.823,0.531 3.021,0.688 0.198,0.156 10 true *b 1.885,2.042 2.083,2.208 0.198,0.167 10 true *c 0.833,0.198 1.01,0.354 0.177,0.156 10 true *d 2.542,1.052 2.719,1.208 0.177,0.156 10 true *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-14030  (09808-01030, 09808-01050)
09808-01071  

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.
A374376C01
0.813,0.25 0.969,0.25 0.969,0.25 1.188,0.813 true 1.625,0.385 1.729,0.198 1.729,0.198 1.823,0.198 false 1.635,2.292 2.24,2.292 true 1.208,0.146 1.365,0.146 1.365,0.146 1.563,0.51 true 1.865,1.135 2.375,1.135 true 0.635,0.156 0.948,0.313 0.313,0.156 10 false *a 1.865,0.115 2.177,0.271 0.313,0.156 10 false *b 1.458,2.198 1.771,2.354 0.313,0.156 10 false *c 2.406,1.042 2.625,1.219 0.219,0.177 10 true *d 1.031,0.052 1.25,0.229 0.219,0.177 10 false *d
*a SST (Handle)
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Install SST (handle) to SST (plate).

SST
09808-14030  (09808-01010, 09808-01030, 09808-01050)
09808-01071  


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.



Hide 77020A 22.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A374377

Remove the fuel suction tube set gasket from the fuel tank assembly.