Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0236932 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The combination meter assembly (meter circuit plate) receives vehicle speed signals from the skid control ECU (brake booster with master cylinder assembly) via CAN communication. The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake booster with master cylinder assembly). The skid control ECU (brake booster with master cylinder assembly) supplies power to the vehicle speed sensor. The skid control ECU (brake booster with master cylinder assembly) detects vehicle speed signals based on pulses of the voltage.

HINT:
·

Factors that affect the indicated vehicle speed include the tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using the GTS. For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION

·

If the vehicle speed sensor circuit has a malfunction, the skid control ECU (brake booster with master cylinder assembly) stores DTCs. Troubleshoot the electronically controlled brake system.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR



WIRING DIAGRAM

E277735E16
0.073,3.073 2.135,3.583 2.063,0.51 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.969,3.167 6.333,3.365 3.365,0.198 10 false : CAN Communication Line 5.281,3.115 7.094,3.594 1.813,0.479 10 false Combination Meter Assembly (Meter Circuit Plate)

CAUTION / NOTICE / HINT

NOTICE:

If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


HINT:

Before starting the following inspection, check tire size and tire air pressure.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)

B

2.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speed Meter Operation Speedometer OFF, 0, 40, 80, 120, 160 -
Body Electrical > Combination Meter > Active Test
Tester Display
Speed Meter Operation
50004 122 1
OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

3.CHECK FOR DTC
a.

Check if electronically controlled brake system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output. A
Electronically controlled brake system DTCs are output. B



A

4.READ VALUE USING GTS (VEHICLE SPEED, VEHICLE SPEED METER)

B

4.READ VALUE USING GTS (VEHICLE SPEED, VEHICLE SPEED METER)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus:

i.

for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.


ii.

for Combination Meter: Body Electrical / Combination Meter / Data List.



e.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Maximum wheel speed sensor Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
Vehicle Speed
50003 105 42
Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 122 8

Result:
Result Proceed to
The Data List values of the ECUs match. A
The Data List values of the ECUs do not match. B


HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly (meter circuit plate) is suspected.

·

When the Data List values of the ECUs do not match, a signal output malfunction of the skid control ECU (brake booster with master cylinder assembly) or an internal malfunction of the combination meter assembly (meter circuit plate) is suspected.




A

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

B

5.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)
5.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)
a.

Replace the combination meter assembly (meter circuit plate) with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY

OK:

The operation of the speedometer returns to normal.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)