Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0236932 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Operating Light Control Rheostat does not Change Light Brightness  


DESCRIPTION

The combination meter assembly (meter circuit plate) receives signals from this circuit to adjust the illumination of the combination meter assembly (meter circuit plate). The combination meter assembly (meter circuit plate) sets the illumination level based on the operation of the light control rheostat switch in the combination switch assembly.

WIRING DIAGRAM

E342179E01
1.073,0.833 2.458,1.458 1.385,0.625 10 false Light Control Rheostat Up Switch 1.115,1.74 2.5,2.365 1.385,0.625 10 false Light Control Rheostat Down Switch 0.854,3.063 2.833,3.604 1.979,0.542 10 false Combination Switch Assembly 0.854,2.875 1.156,3.094 0.302,0.219 10 false F12 4.781,2.948 5.083,3.167 0.302,0.219 10 false F6 4.771,3.094 6.583,3.719 1.813,0.625 10 false Combination Meter Assembly (Meter Circuit Plate) 4.969,0.635 5.271,0.854 0.302,0.219 10 false TR 4.656,0.521 4.958,0.74 0.302,0.219 10 false 24 2.844,0.521 3.146,0.74 0.302,0.219 10 false 8 2.833,2.385 3.135,2.604 0.302,0.219 10 false 6 2.646,2.385 2.948,2.604 0.302,0.219 10 false E 2.542,0.521 2.844,0.74 0.302,0.219 10 false RV

CAUTION / NOTICE / HINT

HINT:
·

The meter illumination level can be adjusted by pressing the light control rheostat switch (combination switch assembly).


·

The meter illumination dims when the taillights are turned on.


·

Setting the meter illumination level to maximum brightness cancels the above dimming of the meter illumination.



PROCEDURE

1.READ VALUE USING GTS (LIGHT CONTROL UP SWITCH, LIGHT CONTROL DOWN SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Light Control Up Switch Light control rheostat up switch OFF or ON OFF: Switch released
ON: Switch pressed
-
Light Control Down Switch Light control rheostat down switch OFF or ON OFF: Switch released
ON: Switch pressed
-
Body Electrical > Combination Meter > Data List
Tester Display
Light Control Up Switch
Light Control Down Switch
50003 122 51,50
OK:

Light control rheostat up or down switch condition displayed on the GTS changes with the actual switch operation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

2.INSPECT LIGHT CONTROL RHEOSTAT SWITCH (COMBINATION SWITCH ASSEMBLY)
2.INSPECT LIGHT CONTROL RHEOSTAT SWITCH (COMBINATION SWITCH ASSEMBLY)
a.

Remove the light control rheostat switch (combination switch assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>LIGHT CONTROL RHEOSTAT>REMOVAL


b.

Inspect the light control rheostat switch (combination switch assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>LIGHT CONTROL RHEOSTAT>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - LIGHT CONTROL RHEOSTAT SWITCH (COMBINATION SWITCH ASSEMBLY))

NG

REPLACE LIGHT CONTROL RHEOSTAT SWITCH (COMBINATION SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - LIGHT CONTROL RHEOSTAT SWITCH (COMBINATION SWITCH ASSEMBLY))
a.

Disconnect the F6 combination meter assembly (meter circuit plate) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-24 (TR) - F12-8 (RV) Always Below 1 Ω
F12-6 (E) - Body ground Always Below 1 Ω
F6-24 (TR) or F12-8 (RV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR