Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0236932 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Hybrid System Indicator Malfunction  


DESCRIPTION

A hybrid system indicator has been included on this vehicle. In this circuit, the combination meter assembly (meter circuit plate) receives the eco-zone indicator level signal from the hybrid vehicle control ECU via CAN communication. The combination meter assembly (meter circuit plate) controls the operation of the hybrid system indicator according to the eco-zone indicator level signal received from the hybrid vehicle control ECU via CAN communication.

WIRING DIAGRAM

E277735E17
0.323,3.083 1.313,3.583 0.99,0.5 10 false Hybrid Vehicle Control ECU 2.969,3.167 6.333,3.365 3.365,0.198 10 false : CAN Communication Line 5.271,3.083 7.094,3.573 1.823,0.49 10 false Combination Meter Assembly (Meter Circuit Plate)

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.PERFORM ACTIVE TEST USING GTS (HV SYSTEM INDICATOR)

B

2.PERFORM ACTIVE TEST USING GTS (HV SYSTEM INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
HV System Indicator Hybrid system indicator OFF, MIN, -50, 0, 100, 200, 300, 400, MAX -
Body Electrical > Combination Meter > Active Test
Tester Display
HV System Indicator
50004 122 110
OK:

Hybrid system indicator indication is normal.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (HV SYSTEM INDICATOR)

NG

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

3.READ VALUE USING GTS (HV SYSTEM INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
HV System Indicator Hybrid system indicator value Min.: -512%, Max.: 511% -512 to 511% -
Body Electrical > Combination Meter > Data List
Tester Display
HV System Indicator
50003 122 88
OK:

Hybrid system indicator value displayed on the GTS is almost the same as the hybrid system indicator indication.



Result:
Proceed to
OK
NG



OK

4.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

4.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)
a.

Replace the combination meter assembly (meter circuit plate) with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY

OK:

The operation of the hybrid system indicator returns to normal.



Result:
Proceed to
OK
NG



OK

END

NG