Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER
RM3210E _53 Suspension _047519 FRONT SUSPENSION _0237145 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48158C 1.INSTALL FRONT LOWER COIL SPRING INSULATOR

a.
C344913C01
0,0 0,0 false
V100135

Positioning Pin


Install the front lower coil spring insulator to the front shock absorber assembly.

NOTICE:

When installing the front lower coil spring insulator, insert the positioning pin of the spring seat into the hole of the front lower coil spring insulator.



Hide 48331C 2.INSTALL FRONT SPRING BUMPER

a.
C344914

Install the front spring bumper to the front shock absorber assembly.

NOTICE:
·

Face the smaller diameter end of the front spring bumper downward.

·

Do not apply lubricants to the front spring bumper.

·

Do not apply lubricants to the front shock absorber assembly cap or rod.

·

Do not clean the front spring bumper with water or solvent.




Hide 48132 3.INSTALL FRONT COIL SPRING

a.
C287918N04
2.427,1.281 2.427,0.979 2.427,0.979 2.688,0.979 false 2.729,0.906 3.188,1.104 0.458,0.198 10 false SST

Secure SST in a vise.

SST
09727-00051  
09727-30022  (09727-00010, 09727-00031)


b.

Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·
C322989

Make sure that the hooks are securely attached to the coil spring.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C344903

Make sure that the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C312080

Make sure that the arms of SST are parallel and the number of coils between the arms is the same on each side.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.




c.

Install the stopper pins to the hooks of SST.

CAUTION:
C322990

·

Make sure that the stopper pins are installed securely.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.




d.

Using SST, compress the coil spring.

CAUTION:
·
C344905

If the coil spring starts to bow out while using SST, stop immediately and reattach SST correctly.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C344906

Do not compress the coil spring to the point where the coils touch each other.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C344907

Do not use an impact wrench.

·

If an impact wrench is used, the threads of SST may be damaged, or sudden compression of the coil spring may cause a hook to disengage and the coil spring to fly out, resulting in injury.

·
C344912N01
0.885,3.167 1.708,3.167 true 0.583,3.083 0.896,3.24 0.313,0.156 10 false SST

If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

·

If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.



SST
09727-00110  


e.
C344915C01
0.542,0.417 0.708,0.417 0.708,0.417 0.708,1.354 true 0.375,0.333 0.688,0.49 0.313,0.156 10 false *a
*a Depression


Align the end of the front coil spring with the flange of the front lower coil spring insulator and install the front coil spring.

NOTICE:

Make sure to fit the end of the front coil spring that has the larger diameter into the depression of the front lower coil spring insulator.



Hide 48045A 4.INSTALL FRONT SPRING SEAT SUB-ASSEMBLY WITH INSULATOR

a.
C345391C01
2.885,1.677 2.792,1.677 2.792,1.677 2.427,1.146 true 2.573,1.104 3.031,0.927 3.031,0.927 3.125,0.927 true 3.167,0.844 3.396,1.052 0.229,0.208 10 false *1 2.927,1.583 3.24,1.74 0.313,0.156 10 false *a
*1 Strut Mounting Bearing
*a Top End of the Insulator (Shock Absorber Dust Cover)


Install the front spring seat sub-assembly with insulator to the front shock absorber assembly.

NOTICE:

Make sure that the top end of the insulator (shock absorber dust cover) and the strut mounting bearing are securely attached.



Hide 48609 5.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.
C344916C01
2.146,0.854 2.604,0.25 2.604,0.25 2.729,0.25 true 2.771,0.167 3.083,0.323 0.313,0.156 10 false *a
*a Slot
V100135

Outside of the Vehicle


Install the front suspension support sub-assembly as shown in the illustration.

NOTICE:

Check that the slot on the piston rod and the slot on the front suspension support sub-assembly are aligned.



b.
C344917C01
0.625,0.948 1.5,0.948 true 1.667,0.5 0.917,0.198 0.917,0.198 0.813,0.198 true 1.729,3.26 2.583,3.635 2.583,3.635 2.688,3.635 true 1.729,3.167 2.573,2.906 2.573,2.906 2.677,2.906 true 0.677,1.875 1.552,1.875 true 1.823,1.875 2.698,1.875 true 2.073,0.188 2.385,0.344 0.313,0.156 10 false *a 2.052,2.375 2.365,2.531 0.313,0.156 10 false *c 0.448,0.875 0.76,1.031 0.313,0.156 10 false *e 2.719,2.844 3.031,3 0.313,0.156 10 false *f 2.729,3.573 3.042,3.729 0.313,0.156 10 false *g 2.75,1.813 3.063,1.969 0.313,0.156 10 false *b 0.5,1.813 0.813,1.969 0.313,0.156 10 false *b 0.646,0.135 0.958,0.292 0.313,0.156 10 false *d
*a 0°+/- 5°
*b Guide Line of Front Suspension Support Sub-assembly
*c Area in Which Protrusions Must Be Aligned
*d Protrusion of Front Suspension Support Sub-assembly
*e Front Shock Absorber Lower Bracket
*f Protrusion of Upper Case
*g Protrusion of Lower Case
V100135

Outside of the Vehicle


Align the protrusion of the front suspension support sub-assembly with the front shock absorber lower bracket as shown in the illustration.

NOTICE:

Make sure to install the front suspension support sub-assembly so that the protrusion of the front suspension support sub-assembly is aligned within +/- 5° of the center of the front shock absorber lower bracket.



c.

Align the protrusions of the upper case and lower case of the strut mounting bearing as shown in the illustration.

NOTICE:

Make sure to install the front spring seat sub-assembly with insulator so that the protrusion of the upper case of the strut mounting bearing overlaps with the protrusion of the lower case within the guide lines of the front suspension support sub-assembly.



Hide 6.INSTALL COLLAR

a.

Install the collar to the front shock absorber assembly.


Hide 48609E 7.TEMPORARILY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.

Temporarily tighten a new front support to front shock absorber nut.


b.

Remove SST from the front coil spring.

NOTICE:

Do not use an impact wrench. It will damage SST.



Hide 48045A 8.CONNECT FRONT SPRING SEAT SUB-ASSEMBLY WITH INSULATOR

a.
C345392C01
0.292,1.688 0.385,1.688 0.385,1.688 1,1.49 true 1.146,1.427 1.531,1.958 1.531,1.958 1.927,1.438 true 1.469,1.979 1.781,2.135 0.313,0.156 10 false *a 0.125,1.625 0.438,1.781 0.313,0.156 10 false *1
*1 Front Spring Seat Sub-assembly with Insulator
*a Claw


Connect the end of the insulator of the front spring seat sub-assembly with insulator with the claws of the front shock absorber assembly.

NOTICE:
·

Make sure that the end of the insulator is securely attached to the claws of the front shock absorber assembly.

·

Make sure there is no excessive damage to the bellows of the insulator.

·

Do not allow oil, grease, etc., to contact the insulator.

·

If oil or grease has adhered, wipe clean with a cloth. Do not use an alcohol based cleaner.




Hide 9.INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C337593

Install the front shock absorber with coil spring (upper side) with the nut and 2 spacers.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


b.
C344896

Temporarily install the 2 nuts to the front shock absorber assembly.


c.

Install the front shock absorber with coil spring (lower side) to the steering knuckle with the 2 bolts and 2 nuts.

Torque:
240 N*m (2447 kgf*cm, 177 ft.*lbf)

NOTICE:
·

When installing the nuts, keep the bolts from rotating.

·

Do not apply lubricants to the steering knuckle and shock absorber contact surfaces.



HINT:

The bolts can be installed in either direction, however, make sure that they are both installed in the same direction.



Hide 89543 10.INSTALL FRONT SPEED SENSOR

a.
C344868C01
0,0 0,0 false
V100135

Hook


Set the 2 hooks of front speed sensor to the front shock absorber assembly.

NOTICE:

Do not twist the front speed sensor when installing it.



b.
C344900

Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.

Engage the clamp.


Hide 48810 11.INSTALL FRONT STABILIZER LINK ASSEMBLY

a.

Install the front stabilizer link assembly to the front shock absorber assembly with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48609E 12.FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.

Fully tighten the front support to front shock absorber nut.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)

NOTICE:

Perform this step only when the front shock absorber with coil spring has been disassembled.



b.
C344896

Remove the 2 nuts from the front shock absorber assembly.


Hide 48684B 13.INSTALL FRONT SUSPENSION SUPPORT DUST COVER

a.

Install the front suspension support dust cover.


Hide 55701J 14.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

a.

for LHD:

i.
C344892

Install the outer cowl top panel sub-assembly with the 7 bolts and 4 nuts.

Torque:
Bolt : 12 N*m (122 kgf*cm, 9 ft.*lbf)
Nut : 50 N*m (510 kgf*cm, 37 ft.*lbf)


ii.
C344891

Engage the 2 clamps to install the wire harness to the outer cowl top panel sub-assembly.



b.

for RHD:

i.
C344893

Install the outer cowl top panel sub-assembly with the 7 bolts and 4 nuts.

Torque:
Bolt : 12 N*m (122 kgf*cm, 9 ft.*lbf)
Nut : 50 N*m (510 kgf*cm, 37 ft.*lbf)


ii.
C344890

Engage the 2 clamps to install the wire harness to the outer cowl top panel sub-assembly.



Hide 55736D 15.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

a.

Install the cowl body mounting reinforcement LH to the outer cowl top panel sub-assembly and vehicle body with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 55735A 16.INSTALL WATER GUARD PLATE LH

a.

Engage the claw to install the water guard plate LH to the outer cowl top panel sub-assembly.


Hide 55737B 17.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

a.

Engage the 2 claws to install the No. 1 heater air duct splash shield seal to the outer cowl top panel sub-assembly.


Hide 55738D 18.INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

a.

Engage the 2 claws to install the No. 2 heater air duct splash shield seal to the outer cowl top panel sub-assembly.


Hide 19.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 20.INSTALL FRONT WHEEL

Hide 21.STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Bounce the vehicle up and down several times to stabilize the suspension.


Hide 22.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 23.PERFORM INITIALIZATION

Intelligent clearance sonar system
Simple intelligent parking assist system
(Click here)
Parking assist monitor system (Click here)
Automatic headlight beam level control system (Click here)