Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER
RM3210E _53 Suspension _047519 FRONT SUSPENSION _0237145 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front shock absorber assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple intelligent parking assist system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 3.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

a.
C344888

Disengage the 2 claws and remove the No. 1 heater air duct splash shield seal from the outer cowl top panel sub-assembly.


Hide 55738D 4.REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

a.
C344885

Disengage the 2 claws and remove the No. 2 heater air duct splash shield seal from the outer cowl top panel sub-assembly.


Hide 55735A 5.REMOVE WATER GUARD PLATE LH

a.

for LHD:

i.
C344887

Disengage the claw and remove the water guard plate LH.



b.

for RHD:

i.
C344886

Disengage the claw and remove the water guard plate LH.



Hide 55736D 6.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

a.

for LHD:

i.
C344884

Remove the 4 bolts and cowl body mounting reinforcement LH from the outer cowl top panel sub-assembly and vehicle body.



b.

for RHD:

i.
C344883

Remove the 4 bolts and cowl body mounting reinforcement LH from the outer cowl top panel sub-assembly and vehicle body.



Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

a.

for LHD:

i.
C344891

Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.


ii.
C344892

Remove the 7 bolts, 4 nuts and outer cowl top panel sub-assembly.



b.

for RHD:

i.
C344890

Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.


ii.
C344893

Remove the 7 bolts, 4 nuts and outer cowl top panel sub-assembly.



Hide 48684B 8.REMOVE FRONT SUSPENSION SUPPORT DUST COVER

a.
C344895

Remove the front suspension support dust cover from the front shock absorber assembly.


Hide 48609E 9.LOOSEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C344897

Temporarily install the 2 nuts to the front shock absorber assembly.


b.
C344899

Loosen the front support to front shock absorber nut.

CAUTION:
C320511

·

Only loosen the front support to front shock absorber nut if the front shock absorber with coil spring needs to be disassembled.

·

Only loosen the front support to front shock absorber nut, do not remove it.

·

If the front support to front shock absorber nut is removed with the front coil spring under tension, components of the front shock absorber with coil spring may fly off.




Hide 48810 10.SEPARATE FRONT STABILIZER LINK ASSEMBLY

a.
C348712

Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 89543 11.SEPARATE FRONT SPEED SENSOR

a.
C344900

Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.



Hide 12.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C344901C02
2.188,1.417 2.833,1.417 true 0.813,2.188 1.354,2.188 false 2.875,1.354 3.188,1.51 0.313,0.156 10 false *a 0.646,2.115 0.958,2.271 0.313,0.156 10 false *b
*a Wooden Block
*b Jack
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Support the front lower No. 1 suspension arm sub-assembly using a jack and wooden block.

NOTICE:

Keep the front lower No. 1 suspension arm sub-assembly supported until installation of the front shock absorber with coil spring is complete.



b.
C344902

Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

NOTICE:
·

When removing the nuts, keep the bolts from rotating.

·

Use wire or an equivalent tool to hang the separated steering knuckle.




c.
C351018

Remove the 3 nuts, 2 spacers and front shock absorber with coil spring.


Hide 48609E 13.REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C287918N04
2.427,1.281 2.427,0.979 2.427,0.979 2.688,0.979 false 2.729,0.906 3.188,1.104 0.458,0.198 10 false SST

Secure SST in a vise.

SST
09727-00051  
09727-30022  (09727-00010, 09727-00031)


b.

Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·
C322989

Make sure that the hooks are securely attached to the coil spring.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C344903

Make sure that the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C312080

Make sure that the arms of SST are parallel and the number of coils between the arms is the same on each side.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.




c.

Install the stopper pins to the hooks of SST.

CAUTION:
C322990

·

Make sure that the stopper pins are installed securely.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.




d.
C344904C02
0.448,0.854 0.906,0.854 false 0.646,0.854 0.646,1.031 0.646,1.031 1.188,1.031 true 1.573,1.146 2.948,1.146 true 1.375,1.333 2.208,1.333 2.208,1.333 2.208,1.146 true 2.99,1.083 3.302,1.24 0.313,0.156 10 false SST 0.281,0.781 0.594,0.938 0.313,0.156 10 false *a
*a Vehicle Nut


Install SST and 2 vehicle nuts to the upper support as shown in the illustration.

SST
09727-30022  (09727-00090, 09727-00100)


e.

Using SST, compress the coil spring.

CAUTION:
·
C344905

If the coil spring starts to bow out while using SST, stop immediately and reattach SST correctly.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C344906

Do not compress the coil spring to the point where the coils touch each other.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C344907

Do not use an impact wrench.

·

If an impact wrench is used, the threads of SST may be damaged, or sudden compression of the coil spring may cause a hook to disengage and the coil spring to fly out, resulting in injury.

·
C344908C02
0.792,3.125 1.74,3.125 true 0.49,3.042 0.802,3.198 0.313,0.156 10 false SST

If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

·

If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.



SST
09727-00110  


f.

Check that the coil spring has become detached, and then remove the front support to front shock absorber nut.

CAUTION:
C344909

·

Do not remove the front support to front shock absorber nut while the coil spring is under tension.

·

If the front support to front shock absorber nut is removed with the coil spring under tension, components of the front shock absorber with coil spring may fly off, resulting in injury.




Hide 14.REMOVE COLLAR

a.

Remove the collar from the front shock absorber assembly.


Hide 48609 15.REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.

Remove the front suspension support sub-assembly from the front shock absorber assembly.


Hide 48045A 16.REMOVE FRONT SPRING SEAT SUB-ASSEMBLY WITH INSULATOR

a.
C344875C02
0.75,1.719 0.854,1.719 0.854,1.719 1.469,1.594 true 1.531,1.552 1.792,1.938 1.792,1.938 2.042,1.542 true 0.583,1.646 0.896,1.802 0.313,0.156 10 false *1 1.74,1.969 2.052,2.125 0.313,0.156 10 false *a
*1 Front Spring Seat Sub-assembly with Insulator
*a Claw


Disengage the front spring seat sub-assembly with insulator from the claws of the front shock absorber assembly.


b.

Remove the front spring seat sub-assembly with insulator from the front shock absorber assembly.


Hide 48132 17.REMOVE FRONT COIL SPRING

a.

Remove the front coil spring and SST.

NOTICE:

Do not use an impact wrench. It will damage SST.



Hide 48331C 18.REMOVE FRONT SPRING BUMPER

a.

Remove the front spring bumper from the front shock absorber assembly.


Hide 48158C 19.REMOVE FRONT LOWER COIL SPRING INSULATOR

a.

Remove the front lower coil spring insulator from the front shock absorber assembly.


Hide 48520 20.REMOVE FRONT SHOCK ABSORBER ASSEMBLY