Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM3210E _58 Vehicle Interior _047513 DOOR LOCK _0237309 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
·

Front door glass sub-assembly

·

Front door glass run


Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284F 3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

Hide 74220 4.REMOVE FRONT ARMREST ASSEMBLY

Hide 5.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Hide 81230 7.REMOVE COURTESY LIGHT ASSEMBLY

Hide 67602 8.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 9.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

Hide 67832 10.REMOVE FRONT DOOR SERVICE HOLE COVER

Hide 68102 11.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Hide 68151D 12.REMOVE FRONT DOOR GLASS RUN

Hide 67404F 13.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Hide 69220 14.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

Hide 15.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

Hide 69040A 16.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

a.
B432418C01
3.031,3.167 2.875,2.854 false 2.99,3.177 3.177,3.354 0.188,0.177 10 true *1
*1 Front Door Lock Open Rod
V113147

Remove in this Direction


Disconnect the connector.


b.

Using a T30 "TORX" socket wrench, remove the 3 screws.


c.

Slide the front door lock with motor assembly downward to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.


d.

When reusing the front door lock with motor assembly:

i.
B432420

Remove the door lock wiring harness seal from the front door lock with motor assembly.



Hide 69720B 17.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

a.
B432421

Using a screwdriver, disengage the 5 claws to open the cover as shown in the illustration.


b.
B432423C01
1.635,0.604 1.781,0.635 false
V113147

Remove in this Direction


Remove the front door lock remote control cable assembly as shown in the illustration.


Hide 69760C 18.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

a.
B432425C01
1.531,0.896 1.698,0.938 false
V113147

Remove in this Direction


Remove the front door inside locking cable assembly as shown in the illustration.


Hide 69720B 19.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

a.
B424076

Using a screwdriver, disengage the 7 claws to open the cover as shown in the illustration.


b.
B424080C01
1.635,0.604 1.792,0.646 false
V113147

Remove in this Direction


Remove the front door lock remote control cable assembly as shown in the illustration.


Hide 69760C 20.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

a.
B424084C01
1.448,0.875 1.656,0.896 false
V113147

Remove in this Direction


Remove the front door inside locking cable assembly as shown in the illustration.