Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM3210E _59 Vehicle Exterior _047505 DOOR / HATCH _0244373 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front door removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
·

Door window regulator assembly

·

Door glass

·

Door glass run


Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

*1: When performing learning using the GTS. Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284F 3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B435679

Using a moulding remover, disengage the 3 claws to remove the front door inside handle bezel plug.


Hide 74220 4.REMOVE FRONT ARMREST ASSEMBLY

a.
B435681C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 3 clips and 7 claws as shown in the illustration.


b.
B439203C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guide to remove the front armrest assembly as shown in the illustration.


Hide 5.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

a.
B436579C02
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 clips and 4 claws as shown in the illustration.


b.

Disconnect the connector to remove the multiplex network master switch assembly with front door upper armrest base panel.


Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

a.
B436577C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 clips and 4 claws as shown in the illustration.


b.

Disconnect the connector to remove the power window regulator switch assembly with front door upper armrest base panel.


Hide 81230 7.REMOVE COURTESY LIGHT ASSEMBLY

Hide 67602 8.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B439179C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the front door panel as shown in the illustration.


b.
B436581

Remove the 3 screws.


c.
B439215

Disengage the 2 clips.


d.
B436582

Using a clip remover, disengage the 10 clips.


e.

Disengage the 6 claws and guide and separate the front door trim board sub-assembly.


f.
B436583C01
2.406,1.271 2.729,0.948 false 2.323,1.615 2.573,1.885 false 2.74,0.844 2.958,1.031 0.219,0.188 10 true *1 2.583,1.833 2.896,2.031 0.313,0.198 10 false *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly
V113147

Remove in this Direction


Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly to remove the front door trim board sub-assembly as shown in the illustration.


Hide 69206B 9.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

B436588

a.

Disengage the 2 claws to remove the front door inside handle sub-assembly.


Hide 10.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

a.
B436585

Disengage the clip.


b.
B436586C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door inner glass weatherstrip with front door vent seal as shown in the illustration.


Hide 67838D 11.REMOVE FRONT DOOR VENT SEAL

a.
B442177C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door vent seal from the front door inner glass weatherstrip as shown in the illustration.


Hide 67856B 12.REMOVE FRONT DOOR PANEL PROTECTOR

Hide 87940 13.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

Hide 67836C 14.REMOVE FRONT DOOR NO. 3 SERVICE HOLE COVER

a.
B436623

Remove the front door No. 3 service hole cover.


Hide 86160 15.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 67832 16.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B436590

Turn each front door weatherstrip clip 45 degrees and remove the 3 front door weatherstrip clips as shown in the illustration.


b.
B436592

Disengage the 4 clips to remove the front door service hole cover.


Hide 68102 18.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.
B436593

Remove the hole plug.


b.

for Driver Side:

i.

Connect the multiplex network master switch assembly.



c.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.

Move the front door glass sub-assembly so that the door glass bolts can be seen.


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

for Driver Side:

i.

Disconnect the multiplex network master switch assembly.



j.

for Front Passenger Side:

i.

Disconnect the power window regulator switch assembly.



k.
B436594

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass sub-assembly to fall.



l.
B436595C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly.



Hide 19.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B436596

Disengage the 2 claws to remove the front door No. 2 service hole cover.


b.
B436597C01
1.563,0.479 2.24,0.885 true 1.344,0.385 1.573,0.573 0.229,0.188 10 true *a
*a Temporary Bolt


Disconnect the connector.


c.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.



d.

Remove the 5 bolts.


e.

Remove the front door window regulator assembly.


f.

Remove the temporary bolt from the front door window regulator assembly.


Hide 68151D 20.REMOVE FRONT DOOR GLASS RUN

a.
B436599

Remove the front door glass run.


Hide 67404F 21.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B436600C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt.


b.

Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.


Hide 69220 22.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B436602

Disengage the 2 claws.


b.

Using a screwdriver, disconnect the connector.


c.
B436612

Disengage the 3 clamps.


d.
B436604C01
0,0 0,0 false
V113147

Disengage in this Direction


Disengage the 2 claws and move the lever as shown in the illustration.


e.
B436606C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door outside handle assembly as shown in the illustration.


Hide 23.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B433544

Remove the hole plug.


b.
B436608

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door lock cylinder assembly.


Hide 69217E 24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B433543

Remove the hole plug.


b.
B436609

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Disengage the 2 guides and claw and remove the front door outside handle cover.


Hide 69241H 25.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B436610

Disengage the 3 claws to remove the front door front outside handle pad.


Hide 69242E 26.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B436611

Disengage the 3 guides and claw to remove the front door rear outside handle pad.


Hide 69040A 27.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69202A 28.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B436613C01
0.073,0.073 0.458,0.406 0.385,0.333 12 false *A 0.073,2.271 0.385,2.521 0.313,0.25 12 false *B
*A Inside
*B Outside


Using a T30 "TORX" socket wrench, remove the screw.


b.

Slide the front door outside handle frame sub-assembly to disengage the claw and remove the front door outside handle frame sub-assembly.


Hide 69312 29.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B436615C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 68610 30.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B436616

Remove the 3 bolts and front door check assembly.


Hide 67862 31.REMOVE FRONT DOOR WEATHERSTRIP

a.
B436617

Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.


Hide 67664C 32.REMOVE DOOR FRAME GARNISH

a.
B436589

Disengage the 3 claws to remove the door frame garnish.


Hide 67402F 33.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B436618C01
0,0 0,0 false
V100135

Bolt
V100136

Screw


Remove the 3 bolts, screw and front door front lower frame sub-assembly.


Hide 68126 34.REMOVE FRONT DOOR FIX WINDOW GLASS

a.
B436619C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door fix window glass with front door fix window weatherstrip as shown in the illustration.


b.

Remove the front door fix window glass from the front door fix window weatherstrip.


Hide 67001A 35.REMOVE FRONT DOOR PANEL CUSHION

a.
B436621

Disengage the 4 claws to remove the 2 front door panel cushions.


Hide 67837B 36.REMOVE FRONT DOOR DUST PROOF SEAL

a.
B436622

Disengage the 3 claws to remove the 3 front door dust proof seals.


Hide 75720 37.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Hide 75756C 38.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

Hide 75754A 39.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75966B 40.REMOVE FRONT DOOR REAR OUTSIDE STRIPE (w/ Black Out Tape)

Hide 75986B 41.REMOVE FRONT DOOR STRIPE (w/ Black Out Tape)

Hide 75976G 42.REMOVE FRONT DOOR LOWER OUTSIDE STRIPE (w/ Black Out Tape)

Hide 67914 43.REMOVE FRONT DOOR SCUFF PLATE

Hide 62112 44.REMOVE COWL SIDE TRIM BOARD

Hide 75752C 45.REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING