The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.
*1: When performing learning using the GTS.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
69284G
3.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
74260
4.REMOVE REAR ARMREST ASSEMBLY
5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
67604
6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
7.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP WITH REAR DOOR NO. 2 VENT SEAL
67842E
8.REMOVE REAR DOOR SERVICE HOLE COVER
67858B
9.REMOVE REAR DOOR PANEL PROTECTOR
67844A
10.REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER
68152C
11.REMOVE REAR DOOR GLASS RUN
67872
12.DISCONNECT REAR DOOR WEATHERSTRIP
Disconnect the rear door weatherstrip until the screw of the rear door window division bar sub-assembly is visible.
67408E
13.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
68124B
14.REMOVE REAR DOOR QUARTER WINDOW GLASS
68104
15.REMOVE REAR DOOR GLASS SUB-ASSEMBLY
69060A
16.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY
| *a | Release Plate |
|
Remove in this Direction |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the 3 screws.
Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.
When reusing the rear door lock with motor assembly:
Remove the door lock wiring harness seal from the rear door lock with motor assembly.
69740D
17.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)
Using a screwdriver, disengage the 2 claws to open the cover as shown in the illustration.
|
Remove in this Direction |
Remove the rear door lock remote control cable assembly as shown in the illustration.
69780B
18.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)
Using a screwdriver, disengage the 4 claws to open the cover as shown in the illustration.
|
Remove in this Direction |
Remove the rear door inside locking cable assembly as shown in the illustration.
69740D
19.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)
Using a screwdriver, disengage the 2 claws to open the cover as shown in the illustration.
|
Remove in this Direction |
Remove the rear door lock remote control cable assembly as shown in the illustration.
69780B
20.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)
Using a screwdriver, disengage the 5 claws to open the cover as shown in the illustration.
|
Remove in this Direction |
Remove the rear door inside locking cable assembly as shown in the illustration.