Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM3210E _59 Vehicle Exterior _047505 DOOR / HATCH _0244374 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear door removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
·

Door window regulator assembly

·

Door glass

·

Door glass run


Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

*1: When performing learning using the GTS. Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 69284G 3.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B436624

Using a moulding remover, disengage the 3 claws to remove the rear door inside handle bezel plug.


Hide 74260 4.REMOVE REAR ARMREST ASSEMBLY

a.
B436626C01
1.677,0.719 1.688,0.552 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 3 clips and 7 claws to remove the rear armrest assembly as shown in the illustration.


Hide 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

a.
B436628C01
1.698,0.49 1.688,0.365 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 clips and 2 claws as shown in the illustration.


b.

Disconnect the connector to remove the rear power window regulator switch assembly with rear door upper armrest base panel.


Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B439181C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the rear door panel as shown in the illustration.


b.
B436630

Remove the 3 screws.


c.
B439193

Using a clip remover, disengage the 8 clips.


d.
B439194C01
0,0 0,0 false
V113147

Remove in this Direction


Pull out the rear door trim board sub-assembly as shown in the illustration to disengage the guide.


e.

Raise the rear door trim board sub-assembly to separate the rear door trim board sub-assembly with the rear door inner glass weatherstrip and No. 1 door scuff plate clamp.


f.
B436633C01
1.844,1.552 1.958,1.594 false 2.75,1.219 3.01,1.063 false 2.667,1.552 2.875,1.802 false 3.021,0.969 3.281,1.177 0.26,0.208 10 true *1 2.885,1.75 3.146,1.958 0.26,0.208 10 true *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly
V113147

Remove in this Direction


Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly to remove the rear door trim board sub-assembly as shown in the illustration.


g.
B436637

Using a screwdriver, disengage the claw to remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly.


Hide 7.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP WITH REAR DOOR NO. 2 VENT SEAL

a.
B439177

Disengage the 5 claws to remove the rear door inner glass weatherstrip with rear door No. 2 vent seal.


Hide 67848B 8.REMOVE REAR DOOR NO. 2 VENT SEAL

a.
B442194C02
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door No. 2 vent seal from the rear door inner glass weatherstrip.


Hide 69206C 9.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B436639

Disengage the 2 claws to remove the rear door inside handle sub-assembly.


Hide 86160B 10.REMOVE REAR SPEAKER ASSEMBLY

Hide 67674A 11.REMOVE REAR DOOR FRAME GARNISH

a.
B436640

Disengage the 2 claws to remove the rear door frame garnish.


Hide 67842E 12.REMOVE REAR DOOR SERVICE HOLE COVER

a.
B436641

Remove the rear door service hole cover.

HINT:

Remove any remaining butyl tape from the rear door panel.



Hide 67858B 13.REMOVE REAR DOOR PANEL PROTECTOR

a.
B436646

Remove the rear door panel protector.


Hide 67844A 14.REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

a.
B436647

Remove the rear door No. 2 service hole cover.


Hide 68152C 15.REMOVE REAR DOOR GLASS RUN

a.
B436648

Remove the rear door glass run.


Hide 68640A 16.REMOVE REAR DOOR CHECK ASSEMBLY

a.
B436643

Remove the 3 bolts and rear door check assembly.


Hide 67872 17.REMOVE REAR DOOR WEATHERSTRIP

a.
B436644C01
0.354,1.271 0.76,1.104 true 0.385,1.552 0.708,1.74 true 0.781,0.979 0.969,1.146 0.188,0.167 10 true *a 0.729,1.677 0.917,1.844 0.188,0.167 10 true *a
*a Double-sided Tape


Using a clip remover, disengage the 25 clips and remove the rear door weatherstrip.


Hide 67408E 18.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B436649C01
1.688,0.313 1.688,0.26 false
V100135

Screw
V100136

Bolt


Remove the screw, 2 bolts and rear door window division bar sub-assembly.


Hide 68124B 19.REMOVE REAR DOOR QUARTER WINDOW GLASS

a.
B436650C01
2.396,1.021 2.479,1.021 false
V113147

Remove in this Direction


Remove the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.


b.

Remove the rear door quarter window glass from the rear door quarter window weatherstrip.


Hide 68104 20.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

a.
B436651

Separate the rear door glass sub-assembly from the rear door window regulator assembly as shown in the illustration.

NOTICE:

After separating the rear door glass sub-assembly, do not allow it to fall.



b.
B442175C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the rear door glass sub-assembly.

NOTICE:

Do not damage the rear door glass sub-assembly.



Hide 69906B 21.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY

a.
B436653C01
0.885,1.208 1.24,1.344 true 0.698,1.073 1.01,1.271 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the rear door glass channel sub-assembly.

HINT:

Tape the screwdriver tip before use.



Hide 69975A 22.REMOVE REAR DOOR GLASS CHANNEL FILLER

a.

Remove the rear door glass channel filler from the rear door glass sub-assembly.


Hide 23.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY

a.

Disconnect the connector.


b.
B436656C01
1.208,0.271 1.698,0.625 true 1,0.146 1.188,0.313 0.188,0.167 10 true *a
*a Temporary Bolt


Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.



c.

Remove the 3 bolts and rear door window regulator assembly.


d.

Remove the temporary bolt from the rear door window regulator assembly.


Hide 69060A 24.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69240 25.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B436658

Disengage the 2 claws and move the lever as shown in the illustration.


b.
B436660C01
1.042,0.646 0.927,0.74 false
V113147

Remove in this Direction


Remove the rear door outside handle assembly as shown in the illustration.


Hide 69227L 26.REMOVE REAR DOOR OUTSIDE HANDLE COVER

a.
B436662

Using a T30 "TORX" socket wrench, loosen the screw.

HINT:

The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.



b.

Disengage the claw to remove the rear door outside handle cover.


Hide 69241G 27.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B436663

Disengage the 3 claws to remove the rear door front outside handle pad.


Hide 69242G 28.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B436664

Disengage the claw and 3 guides to remove the rear door rear outside handle pad.


Hide 69204A 29.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B436665C01
0.083,0.083 0.344,0.281 0.26,0.198 12 true *A 0.083,2.333 0.344,2.531 0.26,0.198 12 true *B
*A Inside
*B Outside


Using a T30 "TORX" socket wrench, remove the screw.


b.

Slide the rear door outside handle frame sub-assembly to disengage the claw, and then remove it.


Hide 67003C 30.REMOVE REAR DOOR PANEL CUSHION

a.
B436667

Disengage the 2 claws to remove the rear door panel cushion.


Hide 67837C 31.REMOVE REAR DOOR DUST PROOF SEAL

a.
B436668

Disengage the 3 claws to remove the 3 rear door dust proof seals.


Hide 67896 32.REMOVE REAR DOOR NO. 3 WEATHERSTRIP

a.
B436669C01
0.979,2.979 0.948,2.979 false
V100155

Double-sided Tape


Disengage the claw and remove the rear door No. 3 weatherstrip.


Hide 75740 33.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

Hide 75762A 34.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

Hide 75764A 35.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

Hide 75766A 36.REMOVE REAR DOOR REAR WINDOW FRAME MOULDING

Hide 75978H 37.REMOVE REAR DOOR LOWER OUTSIDE STRIPE (w/ Black Out Tape)

Hide 75988C 38.REMOVE REAR DOOR OUTSIDE STRIPE (w/ Black Out Tape)

Hide 75989C 39.REMOVE REAR DOOR UPPER OUTSIDE STRIPE (w/ Black Out Tape)