Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM
RM3210E _59 Vehicle Exterior _047541 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0237698 VEHICLE PROXIMITY NOTIFICATION SYSTEM C

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  B1350  Speaker Circuit  


DESCRIPTION

The vehicle approaching speaker assembly circuit consists of the hybrid vehicle control ECU and vehicle approaching speaker assembly.

This DTC is stored when a malfunction is detected in the vehicle approaching speaker assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B1350 Speaker Circuit Either of the following conditions is met:
·

When sound output voltage is being monitored by the ECU, with the power switch on (IG), battery voltage 10 V or more, and warning sound being produced, a speaker circuit short condition continues for 1 second or more.

·

When sound output voltage is being monitored by the ECU, with the power switch on (IG) and warning sound not being produced, a speaker circuit open condition continues for 5 seconds or more.


·

Hybrid vehicle control ECU

·

Vehicle approaching speaker assembly

·

Harness or connector between hybrid vehicle control ECU and vehicle approaching speaker assembly


If the hybrid vehicle control ECU stores a DTC, the pattern select switch assembly (vehicle approaching speaker switch) indicator light will blink for 16 seconds and then illuminate.

WIRING DIAGRAM

E301969E08
1.927,0.719 2.385,0.917 0.458,0.198 10 false SPK+ 1.958,1.135 2.417,1.333 0.458,0.198 10 false SPK- 2.406,0.573 2.667,0.771 0.26,0.198 10 false 19 2.417,1 2.677,1.198 0.26,0.198 10 false 9 4.813,0.625 5.073,0.823 0.26,0.198 10 false 1 4.823,1.021 5.083,1.219 0.26,0.198 10 false 2 5.021,0.719 5.281,0.917 0.26,0.198 10 false + 5.031,1.125 5.292,1.323 0.26,0.198 10 false - 1.073,1.604 1.531,1.802 0.458,0.198 10 false A50 1.073,1.76 2.885,2.354 1.813,0.594 10 false Hybrid Vehicle Control ECU 4.896,1.552 5.354,1.75 0.458,0.198 10 false A16 4.896,1.708 6.24,2.156 1.344,0.448 10 false Vehicle Approaching Speaker Assembly

PROCEDURE

1.INSPECT VEHICLE APPROACHING SPEAKER ASSEMBLY
a.

Remove the vehicle approaching speaker assembly.

Click hereVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER>REMOVAL


b.

Inspect the vehicle approaching speaker assembly.

Click hereVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - VEHICLE APPROACHING SPEAKER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - VEHICLE APPROACHING SPEAKER ASSEMBLY)
a.

Disconnect the A50 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-19 (SPK+) - A16-1 (+) Always Below 1 Ω
A50-9 (SPK-) - A16-2 (-) Always Below 1 Ω
A50-19 (SPK+) or A16-1 (+) - Body ground Always 10 kΩ or higher
A50-9 (SPK-) or A16-2 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR