Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0238440 THEFT DETERRENT SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B434105N07
2.146,3.104 2.542,3.344 0.396,0.24 4.604,3.083 5,3.323 0.396,0.24 1.396,4.573 1.792,4.813 0.396,0.24 3.729,4.583 4.125,4.823 0.396,0.24 5.292,4.615 5.688,4.854 0.396,0.24 6.292,4.625 6.688,4.865 0.396,0.24 4.646,6.229 5.042,6.469 0.396,0.24 1.51,6.208 1.906,6.448 0.396,0.24 3.417,7.844 3.813,8.083 0.396,0.24 1.667,1.479 1.906,1.479 false 4.031,0.813 4.031,0.24 4.031,0.24 4.146,0.24 false 1.667,1.833 1.906,1.833 false 1.969,1.427 2.281,1.625 0.313,0.198 10 false F17 4.198,0.177 4.51,0.375 0.313,0.198 10 false MB 1.969,1.781 2.281,1.979 0.313,0.198 10 false F18 4.708,3.135 5.021,3.333 0.313,0.198 10 false F17 2.24,3.156 2.552,3.354 0.313,0.198 10 false F18 0.885,1.115 1.198,1.313 0.313,0.198 10 false 3H 0.885,1.677 1.198,1.875 0.313,0.198 10 false 3F 0.896,2.031 1.208,2.229 0.313,0.198 10 false 3L 0.906,2.25 1.219,2.448 0.313,0.198 10 false 3K 5.865,1.146 6.177,1.344 0.313,0.198 10 false 3D 5.854,1.792 6.167,1.99 0.313,0.198 10 false 3A 1.521,4.625 1.833,4.823 0.313,0.198 10 false 3H 3.865,4.635 4.177,4.833 0.313,0.198 10 false 3F 5.427,4.667 5.74,4.865 0.313,0.198 10 false 3L 6.417,4.677 6.729,4.875 0.313,0.198 10 false 3K 1.635,6.271 1.948,6.469 0.313,0.198 10 false 3D 4.76,6.281 5.073,6.479 0.313,0.198 10 false 3A 3.531,7.906 3.844,8.104 0.313,0.198 10 false MB

a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-31 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
MB-30 (ACC) - Body ground - Ignition power supply (ACC signal) Power switch off Below 1 V
Power switch on (ACC) 11 to 14 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
F17-6 (FLCY) - Body ground BR - Body ground Front door courtesy light switch assembly (for LH) input Front door LH closed 10 kΩ or higher
Front door LH open Below 1 Ω
F17-27 (FRCY) - Body ground L - Body ground Front door courtesy light switch assembly (for RH) input Front door RH closed 10 kΩ or higher
Front door RH open Below 1 Ω
MB-13 (LCTY) - Body ground - Rear door courtesy light switch assembly (for LH) input Rear door LH closed 10 kΩ or higher
Rear door LH open Below 1 Ω
MB-2 (RCTY) - Body ground - Rear door courtesy light switch assembly (for RH) input Rear door RH closed 10 kΩ or higher
Rear door RH open Below 1 Ω
MB-4 (BCTY) - Body ground - Back door courtesy light switch input Back door closed 10 kΩ or higher
Back door open Below 1 Ω
F17-11 (HCTY) - Body ground B - Body ground Engine hood courtesy switch input Engine hood open 10 kΩ or higher
Engine hood closed Below 1 Ω


d.

Install the main body ECU (multiplex network body ECU) to instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3D-13 (LSFL) - Body ground GR - Body ground Front door LH unlock detection switch input Front door LH unlocked Below 1 V
Front door LH locked Pulse generation
3D-12 (LSFR) - Body ground V - Body ground Front door RH unlock detection switch input Front door RH unlocked Below 1 V
Front door RH locked Pulse generation
F17-29 (L2) - Body ground V - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock position Below 1 V
Driver door key cylinder off Pulse generation
F17-2 (UL3) - Body ground G - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock position Below 1 V
Driver door key cylinder off Pulse generation
3D-14 (LSR) - Body ground LG - Body ground Rear door LH unlock detection switch input Rear door LH or RH unlocked Below 1 V
Rear door LH and RH locked Pulse generation
3D-14 (LSR) - Body ground LG - Body ground Rear door RH unlock detection switch input Rear door RH or LH unlocked Below 1 V
Rear door RH and LH locked Pulse generation
F18-12 (ISIF) - Body ground*1 P - Body ground Intrusion sensor (theft warning ultrasonic sensor) signal input No moving object detected by sensor 11 to 14 V
Theft deterrent system changed from disarmed state to arming preparation state Pulse generation
(See waveform)
F17-7 (GPBS) - Body ground*1 GR - Body ground Glass breakage sensor signal input Glass breakage sensor circuit not open Below 1 V
3F-26 (SH) - Body ground*2 LG - Body ground Security horn assembly drive Security horn assembly sounding
(Theft deterrent system in alarm sounding state)
Pulse generation
(Below 1 V ← → 11 to 14 V)
F18-18 (SSCL) - Body ground*3 W - Body ground Theft warning siren assembly drive Theft warning siren assembly sounding
(Theft deterrent system in alarm sounding state)
Pulse generation
(Below 1 V ← → 11 to 14 V)
3F-27 (HORN) - Body ground SB - Body ground Vehicle horns drive Vehicle horns sounding
(Theft deterrent system in alarm sounding state)
Pulse generation
(Below 1 V ← → 11 to 14 V)

*1: w/ Intrusion Sensor

*2: w/ Security Horn Assembly

*3: w/o Security Horn Assembly



f.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform (Reference)

C256467C03
1.781,0.302 1.917,0.375 false 2.333,0.302 2.448,0.375 false 1.406,0.063 1.656,0.281 0.25,0.219 10 HI 1.385,0.521 1.688,0.781 0.302,0.26 10 LO 1.625,0.229 1.885,0.458 0.26,0.229 10 *a 2.167,0.219 2.427,0.438 0.26,0.219 10 *b 3.979,0.198 4.271,0.448 0.292,0.25 10 *c 3.979,0.719 4.26,0.958 0.281,0.24 10 *d 2.104,0.75 2.354,0.979 0.25,0.229 10 *e 2.51,0.771 2.76,1 0.25,0.229 10 *f 2.656,1.115 2.938,1.333 0.281,0.219 10 *g 1.51,1.51 1.771,1.708 0.26,0.198 10 *h 3.948,1.51 4.24,1.74 0.292,0.229 10 *i
*a IOUT Initial Signal *b IOUT Initial Response
*c Approximately 1.0 Second *d Initial Diagnosis
*e Approximately 1.0 to 1.6 Seconds *f Approximately 0.05 Seconds
*g Approximately 5.5 Seconds *h Disarmed State
*i Arming Preparation State - -


Measurement Condition:
Item Content
Tester Connection F18-12 (ISIF) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system changed from disarmed state to arming preparation state