Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0238440 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B2764  Short to GND in Intrusion Sensor Signal Circuit  


DESCRIPTION

The intrusion sensor (theft warning ultrasonic sensor) conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the ISIF terminal circuit, the main body ECU (multiplex network body ECU) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2764 Short to GND in Intrusion Sensor Signal Circuit After a normal/malfunction signal is output from the intrusion sensor (theft warning ultrasonic sensor) as a result of self-diagnosis, the following malfunctions are detected:
1.

Short to ground in ISIF terminal circuit

2.

Reception of signals other than normal/malfunction signal


·

Intrusion sensor (Theft warning ultrasonic sensor)

·

Main body ECU (Multiplex network body ECU)

·

Wire harness or connector



WIRING DIAGRAM

B438360E01
3.448,1.531 4.063,1.729 0.615,0.198 10 false IOUT 3.563,0.969 4.177,1.167 0.615,0.198 10 false +B 1.156,1.521 1.771,1.719 0.615,0.198 10 false GND 3.854,0.958 4.469,1.156 0.615,0.198 10 false 1 3.865,1.521 4.479,1.719 0.615,0.198 10 false 2 0.958,1.396 1.573,1.594 0.615,0.198 10 false 3 2.813,0.302 4.323,0.531 1.51,0.229 10 false ECU-DCC NO. 2 0.552,0.135 2.063,0.365 1.51,0.229 10 false from Auxiliary Battery 5.354,1.521 5.969,1.719 0.615,0.198 10 false 12 5.625,1.5 6.24,1.698 0.615,0.198 10 false ISIF 5.417,2.479 6.031,2.677 0.615,0.198 10 false F18 5.417,2.646 7.063,3.052 1.646,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 1.396,2.271 2.01,2.469 0.615,0.198 10 false O15 1.385,2.458 3.344,2.917 1.958,0.458 10 false Intrusion Sensor (Theft Warning Ultrasonic Sensor)

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)
a.

Using an oscilloscope, check the waveform.

B438362C01
3.927,0.146 4.344,0.396 0.417,0.25 4.198,1.969 3.99,1.969 3.99,1.969 3.99,1.156 true 1.01,2.708 1.125,2.708 1.125,2.708 1.271,2.969 false 1.656,2.708 1.771,2.708 1.771,2.708 1.917,2.969 false 2.333,0.208 2.646,0.365 0.313,0.156 10 false *a 0.823,2.635 1.135,2.792 0.313,0.156 10 false *b 1.49,2.635 1.802,2.792 0.313,0.156 10 false *c 3.781,2.656 4.094,2.813 0.313,0.156 10 false *d 3.823,3.167 4.135,3.323 0.313,0.156 10 false *e 1.531,3.25 1.844,3.406 0.313,0.156 10 false *f 2.021,3.229 2.354,3.542 0.333,0.313 10 false *g 2.156,3.583 2.469,3.74 0.313,0.156 10 false *h 0.823,4.146 1.125,4.458 0.302,0.313 10 false *i 3.573,4.104 3.917,4.385 0.344,0.281 10 false *j 4.021,0.198 4.479,0.396 0.458,0.198 10 false O15 4.271,1.896 4.729,2.094 0.458,0.198 10 false IOUT 0.479,2.51 0.792,2.667 0.313,0.156 10 false HI 0.458,2.969 0.771,3.125 0.313,0.156 10 false LO
*a Component with harness connected
(Intrusion Sensor (Theft Warning Ultrasonic Sensor))
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 Second
*e Initial Diagnosis *f Approximately 1.0 to 1.6 Seconds
*g Approximately 0.05 Seconds *h Approximately 5.5 Seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition:
Item Content
Tester Connection O15-2 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)


HINT:
·

If the intrusion sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform is output properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG



OK

NG

2.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)
2.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)
a.

Disconnect the O15 intrusion sensor (theft warning ultrasonic sensor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Measurement Condition:
Item Content
Tester Connection O15-2 (IOUT) - O15-3 (GND)
Condition Immediately after theft deterrent system is set



Result:
Result Proceed to
IOUT voltage is below 1 V when theft deterrent system is set A
IOUT voltage is 6.5 V or higher when theft deterrent system is set B



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))

B

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))
a.

Disconnect the F18 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F18-12 (ISIF) - O15-2 (IOUT) Always Below 1 Ω
F18-12 (ISIF) or O15-2 (IOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR