Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0239265 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  Steering Pad Switch Circuit  


DESCRIPTION

The driving support ECU assembly receives a lane departure alert switch signal from the steering pad switch assembly and sends the signal to the forward recognition camera via CAN communication.

WIRING DIAGRAM

A360759E17
0.177,2.385 2.25,2.635 2.073,0.25 10 false Steering Pad Switch Assembly 2.26,1.729 3.167,2.104 0.906,0.375 10 false Spiral Cable Sub-assembly 4.031,2.177 5.323,2.563 1.292,0.385 10 false Driving Support ECU Assembly 5.792,2.177 7.063,2.552 1.271,0.375 10 false Forward Recognition Camera 0.615,1.365 1.708,1.75 1.094,0.385 10 false Lane Departure Alert Main Switch 2.563,1.094 2.948,1.26 0.385,0.167 10 false ECC 2.552,0.49 2.938,0.656 0.385,0.167 10 false DIST 4.49,0.604 5.031,0.792 0.542,0.188 10 false SPSW 4.844,0.844 5.229,1.01 0.385,0.167 10 false CA1N 4.865,1.521 5.25,1.688 0.385,0.167 10 false CA1P 6.208,0.844 6.594,1.01 0.385,0.167 10 false CANL 6.219,1.5 6.677,1.688 0.458,0.188 10 false CANH 0.917,0.75 1.323,0.917 0.406,0.167 10 false 240Ω 2.073,0.406 2.26,0.573 0.188,0.167 10 false 4 2.073,1 2.26,1.167 0.188,0.167 10 false 7 3.198,0.406 3.438,0.573 0.24,0.167 10 false 12 3.24,1.01 3.427,1.177 0.188,0.167 10 false 2 4.25,0.5 4.49,0.667 0.24,0.167 10 false 23 5.292,0.698 5.479,0.865 0.188,0.167 10 false 9 5.292,1.344 5.479,1.51 0.188,0.167 10 false 8 5.99,0.698 6.177,0.865 0.188,0.167 10 false 12 6.063,1.354 6.25,1.521 0.188,0.167 10 false 6 5.792,2 6.177,2.167 0.385,0.167 10 false O7 2.031,0.594 2.302,0.76 0.271,0.167 10 false z3 2.031,1.198 2.302,1.365 0.271,0.167 10 false z3 3.167,1.208 3.448,1.385 0.281,0.177 10 false F21 4.042,1.99 4.458,2.167 0.417,0.177 10 false F40 0.615,3.333 2.521,3.552 1.906,0.219 10 false : CAN Communication Line 3.167,0.594 3.448,0.771 0.281,0.177 10 false F21

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Can Bus Check.

CAN Bus Check
50007

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (HEALTH CHECK)

B

2.CHECK FOR DTCs (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check DTCs.


f.

Turn the power switch off.


Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



A

3.INSPECT STEERING PAD SWITCH ASSEMBLY

B

GO TO DTC CHART

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

b.

Disconnect the z3 steering pad switch assembly connector.

A375988C03
3.406,0.063 3.698,0.26 0.292,0.198 2.5,0.865 3.198,0.865 true 3.656,0.667 4.25,0.375 true 5.333,2.604 5.667,3.104 true 2.844,0.115 3.156,0.271 0.313,0.156 10 false *a 5.688,3.125 6,3.281 0.313,0.156 10 false *b 3.479,0.083 3.792,0.281 0.313,0.198 10 false z3 4.302,0.281 4.917,0.479 0.615,0.198 10 false DIST 2.188,0.792 2.802,0.99 0.615,0.198 10 false ECC
*a Front view of wire harness connector
(Steering Pad Switch Assembly)
*b Lane Departure Alert Main Switch



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-4 (DIST) - z3-7 (ECC) Lane departure alert main switch pushed and held 228 to 252 Ω
Lane departure alert main switch not pushed 10 kΩ or higher



d.

Reconnect the z3 steering pad switch assembly connector.


e.

Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the F21 spiral cable sub-assembly connector.


b.

Disconnect the F40 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F21-12 (DIST) - F40-23 (SPSW) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F21-12 (DIST) or F40-23 (SPSW) - Body ground Always 10 kΩ or higher



d.

Connect the F40 driving support ECU assembly connector.


e.

Connect the F21 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the F21 spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F21-2 (ECC) - Body ground Always Below 1 Ω



c.

Reconnect the F21 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR