Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM
RM3210E _58 Vehicle Interior _047529 PRE-CRASH SAFETY _0239266 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U023A  Lost Communication with Front Camera Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
U023A Lost Communication with Front Camera Module When the power switch is on (IG), a communication error between the forward recognition camera and driving support ECU is detected for approximately 2 seconds.
·

Forward recognition camera branch line or connector

·

Forward recognition camera power source circuit

·

Forward recognition camera



WIRING DIAGRAM

B429438E25
0.188,1.833 2.177,2.042 1.99,0.208 10 false No. 4 CAN Junction Connector 0.198,1.667 0.656,1.865 0.458,0.198 10 false F72 1.635,0.771 1.906,0.969 0.271,0.198 10 false 11 1.635,1.354 1.948,1.552 0.313,0.198 10 false 22 5.406,0.76 5.563,0.958 0.156,0.198 10 false 6 5.344,1.365 5.594,1.563 0.25,0.198 10 false 12 5.406,2.615 5.563,2.813 0.156,0.198 10 false 7 5.333,3.385 5.635,3.594 0.302,0.208 10 false 10 5.573,0.875 6.188,1.073 0.615,0.198 10 false CANH 5.573,1.469 6.188,1.667 0.615,0.198 10 false CANL 5.573,2.708 6.031,2.906 0.458,0.198 10 false IGB 5.563,3.49 6.177,3.688 0.615,0.198 10 false GND 1.177,2.708 2.833,2.917 1.656,0.208 10 false from IG1-NO. 1 Relay 5.167,4.042 7.021,4.26 1.854,0.219 10 false Forward Recognition Camera 5.167,3.875 5.625,4.073 0.458,0.198 10 false O7 3.688,2.854 5.677,3.052 1.99,0.198 10 false ECU-IG1 NO. 4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the connectors of ECUs or wire harnesses while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 2 second or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

2.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)

B

2.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A380142C04
1.531,0.177 1.896,0.448 0.365,0.271 2.146,1.115 2.458,0.979 true 2.146,1.438 2.448,1.521 true 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 1.625,0.24 1.938,0.438 0.313,0.198 10 false O7 2.49,0.896 3.104,1.094 0.615,0.198 10 false CANH 2.5,1.448 3.115,1.646 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the O7 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-6 (CANH) - O7-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



d.

Connect the O7 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A380142C05
1.521,0.167 1.875,0.417 0.354,0.25 0.917,1.542 1.26,1.385 true 1.802,1.427 1.854,1.771 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.604,0.208 1.917,0.406 0.313,0.198 10 false O7 0.646,1.469 1.104,1.667 0.458,0.198 10 false IGB 1.74,1.781 2.198,1.979 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the O7 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O7-7 (IGB) - Body ground Power switch on (IG) 11 to 14 V



e.

Connect the O7 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)