Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0231250 SFI SYSTEM(w/o Canister Pump Module) C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P03402A  Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range  P034031  Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal  


DESCRIPTION

Refer to DTC P034011.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>P034011

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P03402A Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range No camshaft position sensor signal is received by the ECM while the engine is cranking (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Intake camshaft

·

ECM


Comes on DTC stored SAE Code: P0340
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal The camshaft position sensor signal is not received but a normal crankshaft position sensor signal received with the engine running at 600 rpm or higher (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Intake camshaft

·

ECM


Comes on DTC stored SAE Code: P0340

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>P034011

MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine.

10.

Idle the engine for 10 seconds or more.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes.

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P03402A or P034031.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A376492C06
0.281,0.958 0.615,1.167 0.333,0.208 0.865,1.781 1.385,1.188 true 2.677,1.802 1.958,1.188 true 1.656,1.854 1.656,1.219 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 0.333,0.99 0.708,1.188 0.375,0.198 10 false C18 0.708,1.813 1.323,2.01 0.615,0.198 10 false VVI+ 2.635,1.854 2.948,2.052 0.313,0.198 10 false VC 1.552,1.875 2.167,2.073 0.615,0.198 10 false VVI-
*a Front view of wire harness connector
(to Camshaft Position Sensor)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the camshaft position sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C18-3 (VC) - Body ground Power switch on (IG) 4.5 to 5.5 V
C18-1 (VVI+) - Body ground Power switch on (IG) 3.0 to 5.0 V



d.

Turn the power switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C18-3 (VC) - C18-1 (VVI+) Power switch off 1.425 to 1.575 kΩ
C18-2 (VVI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
2.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
A316078C01
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


a.

Check the camshaft position sensor installation condition.

OK:

Camshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

3.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR

3.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the intake camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the intake camshaft.

Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C18-1 (VVI+) - C31-82 (VV1+) Always Below 1 Ω
C18-2 (VVI-) - C31-115 (VV1-) Always Below 1 Ω
C18-3 (VC) - C31-116 (VCV1) Always Below 1 Ω
C18-1 (VVI+) or C31-82 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
C18-2 (VVI-) or C31-115 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
C18-3 (VC) or C31-116 (VCV1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR