Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0239522 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and stereo component amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected When either condition below is met:
·

Stereo component amplifier assembly is/was not connected while the power switch is/was on (ACC or IG).

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the hybrid control system is started.


·

Stereo component amplifier assembly power source circuit

·

AVC-LAN circuit between radio and display receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E334505E03
1.115,4.177 3.26,4.417 2.146,0.24 10 false : AVC-LAN Communication Line 1.292,0.5 3.438,0.74 2.146,0.24 10 false from Auxiliary Battery 1.625,1.073 2.802,1.313 1.177,0.24 10 false from ACC Relay 3.938,0.677 4.354,0.917 0.417,0.24 10 false AMP 3.792,1.25 4.615,1.552 0.823,0.302 10 false ECU-ACC 5.417,3.25 6.625,3.854 1.208,0.604 10 false Stereo Component Amplifier Assembly 2.531,2.906 3.729,3.448 1.198,0.542 10 false Radio and Display Receiver Assembly 2.542,2.74 2.958,2.969 0.417,0.229 10 false F31 5.229,2.885 5.646,3.115 0.417,0.229 10 false F60 5.313,2.677 5.729,2.906 0.417,0.229 10 false 3 5.24,2.354 5.656,2.583 0.417,0.229 10 false F61 5.313,2.156 5.729,2.385 0.417,0.229 10 false 7 5.302,1.656 5.719,1.885 0.417,0.229 10 false 8 5.24,1.083 5.656,1.313 0.417,0.229 10 false F61 5.26,0.896 5.677,1.125 0.417,0.229 10 false 12 5.24,0.521 5.656,0.75 0.417,0.229 10 false F60 5.302,0.344 5.719,0.573 0.417,0.229 10 false 1 5.604,0.521 6.021,0.75 0.417,0.229 10 false +B 5.615,1.073 6.031,1.302 0.417,0.229 10 false ACC 5.604,1.854 6.021,2.083 0.417,0.229 10 false TX+ 5.604,2.333 6.021,2.563 0.417,0.229 10 false TX- 5.594,2.885 6.01,3.115 0.417,0.229 10 false GND 5.24,1.854 5.656,2.083 0.417,0.229 10 false F61 3.219,1.844 3.635,2.083 0.417,0.24 10 false TX1+ 3.25,2.323 3.667,2.563 0.417,0.24 10 false TX1- 3.635,1.729 4.063,1.958 0.427,0.229 10 false 7 3.646,2.208 4.063,2.438 0.417,0.229 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK DTC
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.

Result:
Result Proceed to
DTC B15C3 is not output A
DTC B15C3 is output B




A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.

Disconnect the F60 and F61 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F60-1 (+B) - F60-3 (GND) Power switch off 11 to 14 V
F61-12 (ACC) - F60-3 (GND) Power switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Disconnect the F61 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-7 (TX1+) - F61-8 (TX+) Always Below 1 Ω
F31-8 (TX1-) - F61-7 (TX-) Always Below 1 Ω
F31-7 (TX1+) or F61-8 (TX+) - Body ground Always 10 kΩ or higher
F31-8 (TX1-) or F61-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY