Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0236932 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Malfunction in Water Temperature Warning Light  


DESCRIPTION

In this circuit, the combination meter assembly (meter circuit plate) receives engine coolant temperature signals from the ECM via CAN communication. The combination meter assembly (meter circuit plate) displays an engine coolant temperature warning based on the data received from the ECM.

WIRING DIAGRAM

E143765E85
0.625,3.083 2.021,3.417 1.396,0.333 10 false ECM 2.927,3.156 3.021,3.344 0.094,0.188 10 false : 3.01,3.177 4.656,3.531 1.646,0.354 10 false CAN Communication Line 5.302,3.073 7.115,3.677 1.813,0.604 10 false Combination Meter Assembly (Meter Circuit Plate)

CAUTION / NOTICE / HINT

HINT:

If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores DTCs. Troubleshoot the SFI system.

w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

2.SYSTEM CHECK

B

2.SYSTEM CHECK
a.

Check the engine coolant temperature hot warning light.


Result:
Result Proceed to
Engine coolant temperature hot warning light does not come on. A
Engine coolant temperature hot warning light blinks or remains on. B



A

3.PERFORM ACTIVE TEST USING GTS (INDICAT. LAMP COOLANT HOT)

B

4.CHECK FOR DTC
3.PERFORM ACTIVE TEST USING GTS (INDICAT. LAMP COOLANT HOT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Lamp Coolant Hot Engine coolant temperature hot warning light OFF or ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Lamp Coolant Hot
50004 122 18
OK:

Engine coolant temperature hot warning light operation is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

4.CHECK FOR DTC
a.

Check if SFI system DTCs are output.

w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. B



A

5.READ VALUE USING GTS (COOLANT TEMP, COOLANT TEMPERATURE)

B

5.READ VALUE USING GTS (COOLANT TEMP, COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus:

i.

for Engine: Powertrain / Engine / Data List.


ii.

for Combination Meter: Body Electrical / Combination Meter / Data List.



e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) 75 to 100°C (167 to 212°F): After warming up This is the engine coolant temperature.
HINT:
·

After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.

·

If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.

·

Check if the engine overheats if the value indicated is higher than 135°C (275°F).



Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) 75 to 100°C (167 to 212°F) (After warming up engine) -
Body Electrical > Combination Meter > Data List
Tester Display
Coolant Temperature
50003 122 10

Result:
Result Proceed to
The Data List values of the ECUs do not match. A
The Data List values of the ECUs match. B


HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.

·

When the Data List values of the ECUs do not match, a signal output malfunction of the ECM or an internal malfunction of the combination meter assembly (meter circuit plate) is suspected.




A

6.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

B

6.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)
a.

Replace the combination meter assembly (meter circuit plate) with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY

OK:

The operation of the engine coolant temperature hot warning light returns to normal.



Result:
Proceed to
OK
NG



OK

END

NG