The combination meter mirror ECU receives signals from the radio and display receiver assembly*1 or navigation receiver assembly*2 via local bus communication and displays audio system and navigation system information on the headup display.
This DTC is stored when the combination meter mirror ECU cannot receive the signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B150A | Lost Communication with HMI-LAN | After the combination meter mirror ECU receives a registration information signal, which is sent by the radio and display receiver assembly*1 or navigation receiver assembly*2 when the power switch is on (ACC), 1 or more times, the combination meter mirror ECU cannot receive the signal for 30 seconds or more. | ·
Harness or connector ·
Radio and display receiver assembly*1 ·
Navigation receiver assembly*2 ·
Combination meter mirror ECU |
DTC stored | for Radio and Display Type or Navigation Receiver Type |
*1: for Radio and Display Type
*2: for Navigation Receiver Type
w/ Navigation System
w/o Navigation System
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Navigation System | A |
| w/o Navigation System | B |
A
B
Check if navigation system DTCs are output.
for Radio and Display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR
for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Navigation system DTCs are not output. | A |
| Navigation system DTCs are output. | B |
A
B
for Radio and Display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DIAGNOSTIC TROUBLE CODE CHART
for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DIAGNOSTIC TROUBLE CODE CHART
Disconnect the G7 combination meter mirror ECU connector.
Disconnect the F34 radio and display receiver assembly*1 or F95 navigation receiver assembly*2 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G7-7 (LCL+) - F34-3 (CNH1)*1 | Always | Below 1 Ω |
| G7-8 (LCL-) - F34-4 (CNL1)*1 | Always | Below 1 Ω |
| G7-7 (LCL+) or F34-3 (CNH1) - Body ground*1 | Always | 10 kΩ or higher |
| G7-8 (LCL-) or F34-4 (CNL1) - Body ground*1 | Always | 10 kΩ or higher |
| G7-7 (LCL+) - F95-3 (CNH1)*2 | Always | Below 1 Ω |
| G7-8 (LCL-) - F95-4 (CNL1)*2 | Always | Below 1 Ω |
| G7-7 (LCL+) or F95-3 (CNH1) - Body ground*2 | Always | 10 kΩ or higher |
| G7-8 (LCL-) or F95-4 (CNL1) - Body ground*2 | Always | 10 kΩ or higher |
*1: for Radio and Display Type
*2: for Navigation Receiver Type
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if meter / gauge system DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150A is not output. | A |
| DTC B150A is output (for Radio and Display Type). | B |
| DTC B150A is output (for Navigation Receiver Type). | C |
A
B
C
Check if audio and visual system DTCs are output.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Audio and visual system DTCs are not output. | A |
| Audio and visual system DTCs are output. | B |
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Disconnect the G7 combination meter mirror ECU connector.
Disconnect the F34 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G7-7 (LCL+) - F34-3 (CNH1) | Always | Below 1 Ω |
| G7-8 (LCL-) - F34-4 (CNL1) | Always | Below 1 Ω |
| G7-7 (LCL+) or F34-3 (CNH1) - Body ground | Always | 10 kΩ or higher |
| G7-8 (LCL-) or F34-4 (CNL1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if meter / gauge system DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150A is not output. | A |
| DTC B150A is output. | B |
A
B