If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.
With the electrical key transmitter sub-assembly in the cabin, the power switch is pressed.
When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed with the electrical key transmitter sub-assembly held near the power switch.
When the entry and start system has been canceled, the brake pedal is depressed with the electrical key transmitter sub-assembly held near the power switch.
| Problem Symptom | Data List and Active Test |
|---|---|
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
·
Start Switch1 ·
Start Switch2 ·
Latch Circuit ·
ACC Relay Monitor ·
Power Supply Condition ·
IG Relay Monitor (Outside) ·
IG Relay Monitor (Inside) |
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to entry and start system (for Start Function) Precaution.
After completing repairs, confirm that the problem does not recur.
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
Press a switch of the electrical key transmitter sub-assembly.
The electrical key transmitter sub-assembly LED illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Key Low Battery | Transmitter battery depleted | No or Yes | No: Transmitter battery not depleted
Yes: Transmitter battery depleted |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new). |
| Tester Display |
|---|
| Key Low Battery |
"No" is displayed on the GTS screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the entry lock and unlock functions operate on each door.
If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.
| Result | Proceed to |
|---|---|
| Entry functions operate normally for all doors (w/ Wireless Charging System) | A |
| Entry functions operate normally for all doors (w/o Wireless Charging System) | B |
| An entry function does not operate normally for a door | C |
A
B
C
Wireless charging system off.
Click hereVehicle Interior>POWER OUTLETS (INT)>WIRELESS CHARGING SYSTEM>OPERATION CHECK
Check that interior certification is performed.
| Result | Proceed to |
|---|---|
| Interior certification is not performed normally | A |
| Interior certification is performed normally | B |
A
B
Click hereVehicle Interior>POWER OUTLETS (INT)>WIRELESS CHARGING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Remove the transmitter battery from the electrical key transmitter sub-assembly.
| *1 | Power Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.
The power source mode changes.
If the power source mode changes, the cabin verification is malfunctioning.
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Install the transmitter battery to the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSTALLATION
Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform an entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).
Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform an entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).
Check that the customize setting "Ignition Available Area" is set to "All".
Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (inside luggage compartment) and perform an entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 3 indoor electrical key antenna assembly (inside luggage compartment).
Check that the customize setting "Ignition Available Area" is set to "All".
As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTCs.
DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTCs.
DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antennas in key diagnostic mode.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
It is possible to check which indoor electrical key antenna assembly (front floor, rear floor or inside luggage compartment) is operating by the sounding of the buzzer.
When the wireless buzzer sounds for all indoor electrical key antenna assemblies, they can be judged as operating properly and a malfunction in the certification ECU (smart key ECU assembly), which performs verification, is suspected.
When the wireless buzzer does not sound for all indoor electrical key antenna assemblies, it can be judged that the certification ECU (smart key ECU assembly), which controls the indoor electrical key antenna assemblies, is malfunctioning.
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (front floor).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.
| *a | Inspection Point |
Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.
| Result | Proceed to |
|---|---|
| The wireless buzzer does not sound for all indoor electrical key antenna assemblies | A |
| The wireless buzzer does not sound for only the No. 1 indoor electrical key antenna assembly (front floor) | B |
| The wireless buzzer does not sound for only the No. 2 indoor electrical key antenna assembly (rear floor) | C |
| The wireless buzzer does not sound for only the No. 3 indoor electrical key antenna assembly (inside luggage compartment) | D |
| The wireless buzzer sounds for all indoor electrical key antenna assemblies | E |
A
B
C
D
E
Using an oscilloscope, check the waveform.
| *a | Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Front Floor)) |
*b | Waveform 1 |
| *c | For 30 seconds after closing any door | *d | After 30 seconds or more have elapsed since any door closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F46-1 (ANTE5) - F46-3 (CLGB) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new one.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Console Box)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Check that park (P) is selected.
Press the power switch with the brake pedal released and check that the power source mode changes.
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Using an oscilloscope, check the waveform.
| *a | Front view of wire harness connector
(to No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor)) |
*b | Waveform 1 |
| *c | For 30 seconds after closing any door | *d | After 30 seconds or more have elapsed since any door closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M9-1 (ANTE6) - M9-3 (CLGB) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the No. 2 indoor electrical key antenna assembly (rear floor) with a new one.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Console Box)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Check that park (P) is selected.
Press the power switch with the brake pedal released and check that the power source mode changes.
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Using an oscilloscope, check the waveform.
| *a | Front view of wire harness connector
(to No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment)) |
*b | Waveform 1 |
| *c | For 30 seconds after closing any door | *d | After 30 seconds or more have elapsed since any door closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M31-1 (ANTE7) - M31-3 (CLGB) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the No. 3 indoor electrical key antenna assembly (inside luggage compartment) with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Check that park (P) is selected.
Press the power switch with the brake pedal released and check that the power source mode changes.
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Power switch 1 status | OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
If the power switch is pressed for a short time, the display may not change. ·
Use this item to determine if the power switch input signal is malfunctioning. |
| Start Switch2 | Power switch 2 status | OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal. ·
Behaves the same way as power switch 1. |
| Tester Display |
|---|
| Start Switch1 |
| Start Switch2 |
The GTS display changes correctly in response to the power switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the power switch.
Click hereEngine / Hybrid System>2ZR-FXE STARTING>POWER SWITCH>REMOVAL
Inspect the power switch.
Click hereEngine / Hybrid System>2ZR-FXE STARTING>POWER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-23 (SSW1) - F50-5 (SS1) | Always | Below 1 Ω |
| F1-21 (SSW2) - F50-1 (SS2) | Always | Below 1 Ω |
| F1-11 (AGND) - F50-6 (AGND) | Always | Below 1 Ω |
| F1-23 (SSW1) or F50-5 (SS1) - Body ground | Always | 10 kΩ or higher |
| F1-21 (SSW2) or F50-1 (SS2) - Body ground | Always | 10 kΩ or higher |
| F1-11 (AGND) or F50-6 (AGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antennas in key diagnostic mode.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
It is possible to check if the transponder key amplifier built into the power switch is operating by the sounding of the buzzer.
| *1 | Power Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
Check the power switch.
Face the logo side of the electrical key transmitter sub-assembly toward the power switch, hold the electrical key transmitter sub-assembly near the power switch and check that the wireless buzzer sounds.
| Result | Proceed to |
|---|---|
| The wireless buzzer does not sound | A |
| The wireless buzzer sounds | B |
A
B
Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Entry and start system (for Start Function) DTCs are output | B |
A
B
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3A and 3D instrument panel junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-16 (ACCD) - 3A-30 | Always | Below 1 Ω |
| F1-17 (IG1D) - 3A-17 | Always | Below 1 Ω |
| 3D-3 - Body ground | Always | Below 1 Ω |
| F1-16 (ACCD) or 3A-30 - Body ground | Always | 10 kΩ or higher |
| F1-17 (IG1D) or 3A-17 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-30 - 3D-3 | 20°C (68°F) | 285.71 to 428.57 Ω |
| 3A-17 - 3D-3 | 20°C (68°F) | 142.86 to 214.29 Ω |
| 3K-1 - 3A-40 | Auxiliary battery voltage applied between terminals 3A-30 and 3D-3 | Below 1 Ω |
| Auxiliary battery voltage not applied between terminals 3A-30 and 3D-3 | 10 kΩ or higher | |
| 3K-1 - 3A-35 | Auxiliary battery voltage applied between terminals 3A-17 and 3D-3 | Below 1 Ω |
| Auxiliary battery voltage not applied between terminals 3A-17 and 3D-3 | 10 kΩ or higher | |
| 3K-1 - 3H-12 | Auxiliary battery voltage applied between terminals 3A-17 and 3D-3 | Below 1 Ω |
| Auxiliary battery voltage not applied between terminals 3A-17 and 3D-3 | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Reconnect the F1 certification ECU (smart key ECU assembly) connector.
Measure the voltage while confirming the power source mode on the Data List.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | All OFF, ACC ON, IG ON or ST ON | All OFF: Power switch off
ACC ON: Power switch on (ACC) IG ON: Power switch on (IG) ST ON: Sending hybrid control system start request signal |
- |
| Tester Display |
|---|
| Power Supply Condition |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-17 (IG1D) - Body ground | Power switch off | 1 V or less |
| Power switch on (ACC) | 1 V or less | |
| Power switch on (IG) | 9 V or higher | |
| F1-16 (ACCD) - Body ground | Power switch off | 1 V or less |
| Power switch on (ACC) | 8.5 V or higher | |
| Power switch on (IG) | 8.5 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Inspect the transmitter battery.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSPECTION
Do not wrap the lead wire ground a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG