When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.
When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2341 | Sensor (Motor) Failure | Sensor (motor) failure (The sliding roof ECU (sliding roof drive gear sub-assembly) enters fail-safe mode due to a problem with the motor) | ·
Sliding roof ECU (Sliding roof drive gear sub-assembly) ·
Sliding roof switch (Map light assembly) ·
Wire harness or connector |
| B2344 | Position Failure | Position failure (The sliding roof ECU (sliding roof drive gear sub-assembly) enters fail-safe mode due to a problem with the gear position) | ·
Sliding roof ECU (Sliding roof drive gear sub-assembly) ·
Sliding roof switch (Map light assembly) ·
Wire harness or connector |
If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to How to Proceed with Troubleshooting.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the sliding roof auto operation.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>OPERATION CHECK
Auto operation operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
DTCs B2341 and B2344 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check that the sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
Sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
DTCs B2341 and B2344 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O4 sliding roof switch (map light assembly) connector.
Disconnect the O10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O10-8 (CLS) - O4-5 (CLS) | Always | Below 1 Ω |
| O10-8 (CLS) or O4-5 (CLS) - Body ground | Always | 10 kΩ or higher |
| O10-10 (OPN) - O4-6 (OPN) | Always | Below 1 Ω |
| O10-10 (OPN) or O4-6 (OPN) - Body ground | Always | 10 kΩ or higher |
| O10-9 (DWN) - O4-3 (DOWN) | Always | Below 1 Ω |
| O10-9 (DWN) or O4-3 (DOWN) - Body ground | Always | 10 kΩ or higher |
| O10-5 (UP) - O4-4 (UP) | Always | Below 1 Ω |
| O10-5 (UP) or O4-4 (UP) - Body ground | Always | 10 kΩ or higher |
| O4-11 (GND) - Body ground | Always | Below 1 Ω |
| O10-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the sliding roof switch (map light assembly).
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL
Inspect the sliding roof switch (map light assembly).
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG