Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2015.11–2016.08
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0239522 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B1324  Lost Communication with Meter  B1325  Lost Communication with HUD  


DESCRIPTION

These DTCs are stored when communication between the radio and display receiver assembly and combination meter assembly or headup display (meter mirror sub-assembly) is not possible.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter After the radio and display receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the power switch is on (ACC), 1 or more times, the radio and display receiver assembly does not receive the signal for 30 seconds or more.
·

Local bus communication line

·

Combination meter assembly power source circuit

·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector


B1325 Lost Communication with HUD After the radio and display receiver assembly receives a registration information signal, which is sent by the headup display (meter mirror sub-assembly) when the power switch is on (ACC), 1 or more times, the radio and display receiver assembly does not receive the signal for 30 seconds or more*
·

Local bus communication line

·

Headup display (meter mirror sub-assembly) power source circuit

·

Headup display (meter mirror sub-assembly)*

·

Radio and display receiver assembly

·

Harness or connector



*: w/ Headup Display System


HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

for LHD
E334502E07
5.969,0.552 6.583,0.75 0.615,0.198 10 false CNH1 5.969,0.844 6.583,1.042 0.615,0.198 10 false CNL1 5.802,1.167 6.417,1.365 0.615,0.198 10 false F34 5.802,1.323 7,1.719 1.198,0.396 10 false Radio and Display Receiver Assembly 5.792,0.417 6.063,0.604 0.271,0.188 10 false 3 5.792,0.708 6.063,0.896 0.271,0.188 10 false 4 5.417,0.417 5.688,0.604 0.271,0.188 10 false 2 5.396,0.708 5.667,0.896 0.271,0.188 10 false 13 4.25,0.417 4.521,0.604 0.271,0.188 10 false 1 4.188,0.708 4.458,0.896 0.271,0.188 10 false 12 4.25,2.438 4.521,2.625 0.271,0.188 10 false 3 4.188,2.729 4.458,2.917 0.271,0.188 10 false 14 3.865,0.417 4.135,0.604 0.271,0.188 10 false 33 3.865,0.708 4.135,0.896 0.271,0.188 10 false 34 3.865,1.01 4.135,1.198 0.271,0.188 10 false 28 2.688,0.448 2.958,0.635 0.271,0.188 10 false 22 2.688,0.865 2.958,1.052 0.271,0.188 10 false 21 3.865,2.438 4.135,2.625 0.271,0.188 10 false 7 3.865,2.729 4.135,2.917 0.271,0.188 10 false 8 3.865,3.042 4.135,3.229 0.271,0.188 10 false 6 2.75,2.469 3.021,2.656 0.271,0.188 10 false 1 2.75,2.896 3.021,3.083 0.271,0.188 10 false 2 2.646,3.458 3.26,3.656 0.615,0.198 10 false G7 2.646,3.625 3.948,4.021 1.302,0.396 10 false Combination Meter Mirror ECU* 4.365,3.469 4.979,3.667 0.615,0.198 10 false F79 4.365,3.635 5.979,3.833 1.615,0.198 10 false No. 11 Junction Connector 2.729,1.448 3.344,1.646 0.615,0.198 10 false F6 2.719,1.604 3.99,1.99 1.271,0.385 10 false Meter Circuit Plate 3.375,0.563 3.99,0.76 0.615,0.198 10 false MSCH 3.375,0.844 3.99,1.042 0.615,0.198 10 false MSCL 2.927,0.563 3.188,0.76 0.26,0.198 10 false B 2.927,0.99 3.229,1.188 0.302,0.198 10 false IG+ 3.563,1.115 3.865,1.313 0.302,0.198 10 false ES 3.438,2.583 4.052,2.781 0.615,0.198 10 false LCL+ 3.458,2.875 4.073,3.073 0.615,0.198 10 false LCL- 3.573,3.146 3.875,3.344 0.302,0.198 10 false ES 2.917,2.594 3.177,2.792 0.26,0.198 10 false B 2.927,3.01 3.229,3.208 0.302,0.198 10 false IG 1.708,0.698 2.781,0.906 1.073,0.208 10 false ECU-DCC NO. 2 1.708,2.719 2.781,2.927 1.073,0.208 10 false ECU-DCC NO. 2 1.833,1.115 2.594,1.313 0.76,0.198 10 false METER-IG2 1.729,3.146 2.698,3.333 0.969,0.188 10 false ECU-IG1 NO. 4 0.167,0.531 1.542,0.75 1.375,0.219 10 false from Auxiliary Battery 0.563,0.958 1.719,1.208 1.156,0.25 10 false from IG2 Relay 0.167,2.552 1.542,2.771 1.375,0.219 10 false from Auxiliary Battery 0.177,2.979 1.552,3.198 1.375,0.219 10 false from IG1 NO. 1 Relay 1,5.208 3.646,5.438 2.646,0.229 10 false : Local Bus Communication Line 0.948,4.833 2.802,5.052 1.854,0.219 10 false *: w/ Headup Display System

for RHD
E334502E08
5.969,0.552 6.583,0.75 0.615,0.198 10 false CNH1 5.969,0.844 6.583,1.042 0.615,0.198 10 false CNL1 5.802,1.167 6.417,1.365 0.615,0.198 10 false F34 5.802,1.323 7,1.688 1.198,0.365 10 false Radio and Display Receiver Assembly 5.792,0.417 6.063,0.604 0.271,0.188 10 false 3 5.792,0.708 6.063,0.896 0.271,0.188 10 false 4 5.417,0.417 5.688,0.604 0.271,0.188 10 false 5 5.396,0.708 5.667,0.896 0.271,0.188 10 false 16 4.25,0.417 4.521,0.604 0.271,0.188 10 false 7 4.188,0.708 4.458,0.896 0.271,0.188 10 false 18 4.25,2.438 4.521,2.625 0.271,0.188 10 false 6 4.188,2.729 4.458,2.917 0.271,0.188 10 false 17 3.865,0.417 4.135,0.604 0.271,0.188 10 false 33 3.865,0.708 4.135,0.896 0.271,0.188 10 false 34 3.865,1.01 4.135,1.198 0.271,0.188 10 false 28 2.688,0.448 2.958,0.635 0.271,0.188 10 false 22 2.688,0.865 2.958,1.052 0.271,0.188 10 false 21 3.865,2.438 4.135,2.625 0.271,0.188 10 false 7 3.865,2.729 4.135,2.917 0.271,0.188 10 false 8 3.865,3.042 4.135,3.229 0.271,0.188 10 false 6 2.75,2.469 3.021,2.656 0.271,0.188 10 false 1 2.75,2.896 3.021,3.083 0.271,0.188 10 false 2 2.76,3.458 3.375,3.656 0.615,0.198 10 false G7 2.76,3.615 3.938,4 1.177,0.385 10 false Combination Meter Mirror ECU* 4.365,3.469 4.979,3.667 0.615,0.198 10 false F77 4.365,3.635 6.083,3.865 1.719,0.229 10 false No. 9 Junction Connector 2.729,1.448 3.344,1.646 0.615,0.198 10 false F6 2.719,1.604 3.99,1.99 1.271,0.385 10 false Meter Circuit Plate 3.375,0.563 3.99,0.76 0.615,0.198 10 false MSCH 3.375,0.844 3.99,1.042 0.615,0.198 10 false MSCL 2.927,0.563 3.188,0.76 0.26,0.198 10 false B 2.927,0.99 3.229,1.188 0.302,0.198 10 false IG+ 3.563,1.115 3.865,1.313 0.302,0.198 10 false ES 3.438,2.583 4.052,2.781 0.615,0.198 10 false LCL+ 3.458,2.875 4.073,3.073 0.615,0.198 10 false LCL- 3.573,3.146 3.875,3.344 0.302,0.198 10 false ES 2.917,2.594 3.177,2.792 0.26,0.198 10 false B 2.927,3.01 3.229,3.208 0.302,0.198 10 false IG 1.708,0.698 2.781,0.906 1.073,0.208 10 false ECU-DCC NO. 2 1.708,2.719 2.781,2.927 1.073,0.208 10 false ECU-DCC NO. 2 1.833,1.115 2.594,1.313 0.76,0.198 10 false METER-IG2 1.729,3.146 2.698,3.333 0.969,0.188 10 false ECU-IG1 NO. 4 0.167,0.531 1.542,0.75 1.375,0.219 10 false from Auxiliary Battery 0.167,0.948 1.542,1.167 1.375,0.219 10 false from IG2-NO. 2 Relay 0.167,2.552 1.542,2.771 1.375,0.219 10 false from Auxiliary Battery 0.177,2.979 1.552,3.198 1.375,0.219 10 false from IG1-NO. 1 Relay 1,5.208 3.646,5.438 2.646,0.229 10 false : Local Bus Communication Line 0.948,4.833 2.802,5.052 1.854,0.219 10 false *: w/ Headup Display System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for LHD A
for RHD B




A

2.CHECK DTC

B

22.CHECK DTC
2.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTC B1324 and B1325 are not output A
DTC B1324 and B1325 are output
(w/ Headup Display System)
B
DTC B1324 is output C
DTC B1325 is output
(w/ Headup Display System)
D



A

B

3.CHECK LOCAL BUS

C

12.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE POWER SOURCE)

D

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU POWER SOURCE)
3.CHECK LOCAL BUS
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 - F79-13 Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (Below 54 Ω) B
NG (70 Ω or higher) C



A

B

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)

C

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 - F79-13 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)

NG

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-1 - F79-12 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)

NG

8.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Disconnect the G7 combination meter mirror ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-3 - F79-14 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-3 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-14 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-3 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F79-14 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G7 combination meter mirror ECU connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (LCL+) - G7-8 (LCL-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F6 meter circuit plate connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-33 (MSCH) - F6-34 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F34 radio and display receiver assembly connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-3 (CNH1) - F34-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F34 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-3 (CNH1) - F34-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the F34 radio and display receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 - F79-13 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE POWER SOURCE)
a.

Disconnect the F6 meter circuit plate connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-28 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-22 (B) - Body ground Power switch off 11 to 14 V
F6-21 (IG+) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the F6 meter circuit plate connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-1 - F79-12 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)

NG

16.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
14.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 - F79-13 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

15.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
15.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F34 radio and display receiver assembly connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-3 (CNH1) - F34-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F6 meter circuit plate connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-33 (MSCH) - F6-34 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU POWER SOURCE)
a.

Disconnect the G7 combination meter mirror ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-6 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-1 (B) - Body ground Power switch off 11 to 14 V
G7-2 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Connect the G7 combination meter mirror ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-3 - F79-14 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-3 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-14 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F79-3 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F79-14 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)

NG

21.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
19.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F79 No. 11 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 - F79-13 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

20.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
20.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F34 radio and display receiver assembly connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-3 (CNH1) - F34-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 11 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G7 combination meter mirror ECU connector.


c.

Connect the F79 No. 11 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (LCL+) - G7-8 (LCL-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTC B1324 and B1325 are not output A
DTC B1324 and B1325 are output
(w/ Headup Display System)
B
DTC B1324 is output C
DTC B1325 is output
(w/ Headup Display System)
D



A

B

23.CHECK LOCAL BUS

C

32.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE POWER SOURCE)

D

37.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU POWER SOURCE)
23.CHECK LOCAL BUS
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 - F77-16 Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (Below 54 Ω) B
NG (70 Ω or higher) C



A

B

24.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)

C

30.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
24.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 - F77-16 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)

NG

29.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
25.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-7 - F77-18 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)

NG

28.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
26.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Disconnect the G7 combination meter mirror ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-6 - F77-17 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-6 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-17 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-6 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F77-17 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

27.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
27.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G7 combination meter mirror ECU connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (LCL+) - G7-8 (LCL-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F6 meter circuit plate connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-33 (MSCH) - F6-34 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F34 radio and display receiver assembly connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-3 (CNH1) - F34-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F34 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-3 (CNH1) - F34-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

31.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
31.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the F34 radio and display receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 - F77-16 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE POWER SOURCE)
a.

Disconnect the F6 meter circuit plate connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-28 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-22 (B) - Body ground Power switch off 11 to 14 V
F6-21 (IG+) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

33.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the F6 meter circuit plate connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-7 - F77-18 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

34.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)

NG

36.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
34.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 - F77-16 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

35.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
35.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F34 radio and display receiver assembly connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-3 (CNH1) - F34-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CHECK HARNESS AND CONNECTOR (METER CIRCUIT PLATE - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F6 meter circuit plate connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-33 (MSCH) - F6-34 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU POWER SOURCE)
a.

Disconnect the G7 combination meter mirror ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-6 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G7-1 (B) - Body ground Power switch off 11 to 14 V
G7-2 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

38.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Connect the G7 combination meter mirror ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-6 - F77-17 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-6 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-17 - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F77-6 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F77-17 - G7-1 (B) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

39.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)

NG

41.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
39.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F77 No. 9 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-5 - F77-16 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

40.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
40.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F34 radio and display receiver assembly connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-3 (CNH1) - F34-4 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G7 combination meter mirror ECU connector.


c.

Connect the F77 No. 9 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (LCL+) - G7-8 (LCL-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR