The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines (w/ Sliding Roof).
The radio and display receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines (w/o Sliding Roof).
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Microphone signal is lost | ·
Telephone microphone assembly ·
Radio and display receiver assembly ·
Harness or connector ·
Map light assembly* |
*: w/ Sliding Roof
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/o Sliding Roof) | A |
| OK (w/ Sliding Roof) | B |
| NG | C |
A
B
C
Disconnect the F31 radio and display receiver assembly connector.
Disconnect the O2 telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-6 (SNS2) - O2-3 (SNS2) | Always | Below 1 Ω |
| F31-19 (MIN-) - O2-4 (MCO-) | Always | Below 1 Ω |
| F31-6 (SNS2) or O2-3 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F31-19 (MIN-) or O2-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
| *a | Component without harness connected
(Telephone Microphone Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SNS2) - 4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F31 radio and display receiver assembly connector.
Disconnect the O4 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-6 (SNS2) - O4-14 (SNS2) | Always | Below 1 Ω |
| F31-19 (MIN-) - O4-15 (MCO-) | Always | Below 1 Ω |
| F31-6 (SNS2) or O4-14 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F31-19 (MIN-) or O4-15 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly (telephone microphone assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 14 (SNS2) - 15 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG